An efficient extraction and clean‐up procedure for pesticide determination in olive oil

This work reports a simple, rapid, and effective extraction method based on liquid–liquid extraction (LLE) followed by matrix solid‐phase dispersion‐sonication for detection, identification and quantification of multiclass pesticides in virgin olive oil using liquid chromatography mass spectrometry (LC‐QTOF‐MS). LLE to extract pesticide residues in virgin olive oil was performed in order to study the centrifugation efficiency to obtain high recovery yield and low co‐extract fat residue in the final extract. Different suitable parameters of MSPD procedure were evaluated, such as nature of dispersing phase, clean‐up adsorbent, and volume of eluting solvent (acetonitrile) in different extraction conditions, with or without sonication. The best results were obtained using 5 g of virgin olive oil, 2 g of PSA as dispersant sorbent, 2 g of Florisil/GCB (70:30 w/w) as clean‐up sorbent, and 15 mL of acetonitrile as eluting solvent under conditions of 15 min ultrasonic bath at RT. Method validation was performed in order to study sensitivity, linearity, precision, and accuracy. Average recoveries ranged between 73.7 and 104.2% with relative SDs 5.3–13.4% at three concentration levels (25, 50, and 100 µg/kg). Detection and quantification limits ranged from 1.5 to 5 µg/kg and 3 to 9 µg/kg, respectively.     

Contemporary challenges of soot build-up in IC engine and their tribological implications

Confronted with the contemporary challenges of maximising energy efficiency with minimal impact on the environment, the automotive industry has developed various technologies to tackle them. Most of these technologies, however, have wider implications on the tribological performance of the automotive engines due to resultant soot build-up. This paper reviews the effects that attempts by stakeholders to satisfy requirements for reduced fuel consumption, reduced emissions and extended service intervals have had on increasing soot levels to an extent that can lead to engine component failure. Three areas have been identified that have either not been explored or not widely explored in the study of automotive soot namely: numerical simulation and modelling of soot wear, soot effects on wear of actual engine components and the wear and friction performance of non-metallic materials used in internal combustion engines. A paper-grading system is also utilised to present an overview of how sooty oil-related research covers various areas.     

Synthesis of Chemically Cross-Linked Hydroxypropyl Methyl Cellulose Hydrogels and their Application in Controlled Release of 5-Amino Salicylic Acid

The objective of this study was to achieve the colon-specific delivery of an anti-ulcerative colitis drug using hydroxypropyl methyl cellulose (HPMC) hydrogels. HPMC hydrogels containing poly ethylene glycol (PEG) as cross-links have been prepared by reacting HPMC sodium salt with polyethylene glycol dichloride.

The effect of cross-linking agent on swelling behavior of HPMC-PEG hydrogels, were investigated. Swelling parameters such as equilibrium degree of swelling, swelling ratio and network parameter such as molecular mass between cross-links (M_c) were determined. The cross-linking concentrations were 0.5%, 1%, 1.5%, and 2% (based on weight of HPMC). The equilibrium swelling ratio (Q) of cross-linked HPMC hydrogels increases from 13.2 to 27.1 as the cross-linker percentage increases from 0.5% to 2%. 5-Aminosalicylic acid (5-ASA) was used as a model of an anti-inflammatory drug. Cross-linked HPMC hydrogels were found to be a promising drug delivery system for the drugs to be delivered to the colon.     

Synthesis and Characterization of Molecularly Imprinted Polymer Membrane for the Removal of 2,4-Dinitrophenol

Molecularly imprinted polymers (MIPs) were prepared by bulk polymerization in acetonitrile using 2,4-dinitrophenol, acrylamide, ethylene glycol dimethacrylate, and benzoyl peroxide, as the template, functional monomer, cross-linker, and initiator, respectively. The MIP membrane was prepared by hybridization of MIP particles with cellulose acetate (CA) and polystyrene (PS) after being ground and sieved. The prepared MIP membrane was characterized using Fourier transform infrared spectroscopy and scanning electron microscopy. The parameters studied for the removal of 2,4-dinitrophenol included the effect of pH, sorption kinetics, and the selectivity of the MIP membrane. Maximum sorption of 2,4-nitrophenol by the fabricated CA membrane with MIP (CA-MIP) and the PS membrane with MIP (PS-MIP) was observed at pH 7.0 and pH 5.0, respectively. The sorption of 2,4-dinitrophenol by CA-MIP and PS-MIP followed a pseudo–second-order kinetic model. For a selectivity study, 2,4-dichlorophenol, 3-chlorophenol, and phenol were selected as potential interferences. The sorption capability of CA-MIP and PS-MIP towards 2,4-dinitrophenol was observed to be higher than that of 2,4-dichlorophenol, 3-chlorophenol, or phenol.     

Increasing Resistant Starch Content in Fish Crackers Through Repetitive Cooking-Chilling Cycles

This work describes the effect of a repetitive cooking-chilling process on resistant starch content in crackers prepared from a mixture of fish and starch, which are popularly known in Malaysia as “keropok.” Three fish cracker formulations were prepared using tapioca, wheat, and sago starch. Up to four cycles of repetitive cooking-chilling increased the resistant starch content in all products; however, the hardness of chilled samples decreased, and their moisture content increased. For the fried samples, the texture became harder, the color turned darker, and linear expansion was reduced. The dried fish cracker samples prepared with sago starch yielded the highest resistant starch content. The results demonstrated that four cycles of repetitive cooking-chilling were able to enhance resistant starch in fish crackers.     

Microfluorometric assessment of sperm maturation in testicular biopsies from men with histologically normal or reduced spermatogenesis

Spermatogenesis has been studied in testicular biopsies by means of microfluorometric assessment of the DNA-DNP complex using ethidium bromide in 10 men with histologically normal spermatogenesis and in 10 men with histologically reduced spermatogenesis. The expected haploid DNA value was found in the round spermatids, whereas only 70% of the haploid fluorescence value was found in the elongated spermatids and around 60% in the testicular spermatozoa. No difference was found in the mean fluorescence values between the pathological group and the controls. it is suggested that structural changes or an increase in basic nuclear proteins gradually exclude the ethidium bromide from the binding to the DNA molecule and that this phenomenon occurs concomitantly with a decrease in double-stranded RNA. The difference in fluorescence intensity before and after RNAase treatment was regarded as an approximate estimate of the RNA content. There was a significant decrease of these values during spermatogenesis.     

Development of a novel nanocomposite consisting of 3-(4-methoxyphenyl)propionic acid and magnesium layered hydroxide for controlled-release formulation

ABSTRACT

Magnesium layered hydroxide (MLH) intercalated with anionic 3-(4-methoxyphenyl)propionic acid (MPP) was synthesised by a direct reaction method using magnesium oxide and MPP as precursors. A further coating of chitosan was applied on the external surface of MLH–MPP nanocomposite to form a new material, named MLH–MPP/chitosan nanocomposite. The XRD pattern showed an intense and sharp peak at basal spacing 18.9 Å, proving that MPP anions were successfully intercalated into the interlayer gallery of MLH in a monolayer arrangement. The XRD pattern of the MLH–MPP/chitosan nanocomposite shows similar peaks with the MLH–MPP nanocomposite. The result was also supported by FTIR spectra and elemental analysis. TGA/DTG spectra showed that the thermal stabilities of the guest anion in the both nanocomposites were markedly enhanced. A controlled-release study of the MPP ion from the MLH–MPP/chitosan nanocomposite showed a slower release compared to MLH–MPP nanocomposite with an initial rapid release and slow release thereafter. Meanwhile, the release behaviours of MPP ions from both nanocomposites were governed by pseudo-second order kinetics. This result highlights the potential of the nanocomposite as an encapsulated material for the controlled-release formulation of MPP anions.     

Increasing image compression rate using steganography

The goal of image compression is to remove the redundancies for minimizing the number of bits required to represent an image while steganography works by embedding the secret data in redundancies of the image in invisibility manner. Our focus in this paper is the improvement of image compression through steganography. Even if the purposes of digital steganography and data compression are by definition contradictory, we use these techniques jointly to compress an image. Hence, two schemes exploring this idea are suggested. The first scheme combines a steganographic algorithm with the baseline DCT-based JPEG, while the second one uses this steganographic algorithm with the DWT-based JPEG. In this study data compression is performed twice. First, we take advantage of energy compaction using JPEG to reduce redundant data. Second, we embed some bit blocks within its subsequent blocks of the same image with steganography. The embedded bits not only increase file size of the compressed image, but also decrease the file size further more. Experimental results show for this promising technique to have wide potential in image coding.     

On using available environmental data in service life estimations

In the process of service life prediction or estimation of building and construction components and materials, data of the prevailing exposure environment, (the conditions at and around a building or construction) is required. However, most environmental data is measured by and available from meteorological and air quality research communities. This data is collected at macro and meso levels, some distance from the object studied, and raises the need to transform data in order to describe the specific, local conditions adjacent to that object. To estimate levels of degradation agents in the exposure environment, especially those close to the building or construction at local and micro levels have to be considered. This paper will show and discuss useful environmental data sources, and how to transform such data by means of available distribution models.

Lorsqu'il s'agit de faire des prévisions ou des estimations de durée de vie de bâtiments ainsi que de composants et matériaux de construction, il faut disposer des données sur les conditions prévalantes d'exposition et d'environnement (conditions qui règnent dans un bâtiment ou à proximité). Or, la plupart des données environnementales sont mesurées et fournies par des instituts de recherche en météorologie et qualité de l'air. Ces données sont collectées à grande et à moyenne échelle, à une certaine distance de l'objet étudié, et elles doivent donc être transformées si l'on veut décrire les conditions spécifiques locales à proximité dudit objet. Pour estimer le niveau de dégradation dans l'environnement d'exposition, notamment à proximité des bâtiments ou constructions, il faut considérer les agents au micro-niveau et au niveau local. Cet article présente et examine des sources de données environnementales utiles et montre comment transformer ces données en utilisant les modèles de distribution existants.     

Preparation and Properties of Biodegradable Polymer Film Based on Polyvinyl Alcohol and Tropical Fruit Waste Flour

In this study, two different types of tropical fruit waste flour, rambutan waste flour (RWF) and banana waste flour (BWF), were blended with polyvinyl alcohol (PVOH) by solution casting method. The structure of the blend film was characterised by Fourier Transform Infrared Spectroscopy. The tensile strength and elongation at break of tropical fruit waste flour-filled polyvinyl alcohol were lower, but the tensile modulus was higher, than that of PVOH film. At a similar blend ratio, the tensile properties of the PVOH/RWF film were higher than the PVOH/BWF film, but the PVOH/BWF film showed higher water uptake than PVOH/RWF film.