Ultraviolet Lamp Output Measurement: A Concise Derivation of the Keitz Equation

An equation relating the measured irradiance and the output power of a fluorescent lamp was derived by Keitz. The equation forms the basis for a new protocol that has been proposed for quantifying the total flux from an ultraviolet lamp. There has been confusion in the literature regarding the spatial distribution of flux from lamp emitters, which has led to emission models that are similar to the Keitz model but are incorrect. The Keitz equation is derived here from first principles in an effort to eliminate the confusion and present a correct method of calculating total flux.     

Incorporation of polyfluorenes into poly(lactic acid) films for sensor and optoelectronics applications

Films of neat and plasticized biodegradable poly(lactic acid) (PLA) matrices containing anionic conjugated polyelectrolytes, poly[9,9‐bis(4‐phenoxybutylsulfonate)]fluorene‐2,7‐diyl‐alt‐arylenes, with 1,4‐phenylene and 4,4″‐p‐terphenylene, respectively, as arylene groups or a neutral poly(9,9‐dialkylfluorene) for comparison were prepared by solution casting. These films were characterized using differential scanning calorimetry, thermogravimetry, scanning electron microscopy and fluorescence spectroscopy. In addition, the effects of plasticizer on the thermal properties and the oxygen permeability of the PLA films were measured through the oxygen transmission rate. Results show that it is possible to obtain thin, optically transparent and luminescent films with potential in oxygen sensing, exhibiting good thermal and photochemical stability. At high polyelectrolyte content, evidence is found for phase separation and aggregate formation and it is no longer possible to obtain completely homogeneous films. The possibility of incorporating the cationic metal complex tris(2,2′‐bipyridyl)ruthenium(II) into plasticized PLA films containing conjugated polyelectrolytes for dual‐wavelength ratiometric luminescence sensing is also discussed. Copyright © 2012 Society of Chemical Industry     

Fit‐first to be tied

This poem summarizes the fit‐first method of camera evaluation described in Jim Worthey's “Applications of vectorial color.” The algorithm works with the locus of unit monochromats (LUM) in camera and CIE color‐matching spaces. © 2011 Wiley Periodicals, Inc. Col Res Appl, 2011;     

Effects of level of social contact on dairy calf behavior and health

Housing preweaned dairy calves in pairs rather than individually has been found to positively affect behavioral responses in novel social and environmental situations, but concerns have been raised that close contact among very young animals may impair their health. In previous studies, the level of social contact permitted in individual housing has been auditory, visual, or physical contact. It is unclear how these various levels of social contact compare with each other and to pair housing, when their effects on behavior and health are considered, and whether the timing of pair housing has an effect. To investigate this, 110 Holstein calves (50 males, 60 females) in 11 blocks were paired according to birth date. Within 60 h of birth, each pair of calves was allocated to 1 of 5 treatments: individual housing with auditory contact (I), individual housing with auditory and visual contact (V), individual housing with auditory, visual, and tactile contact (T), pair housing (P), or individual housing with auditory and visual contact the first 2 wk followed by pair housing (VP). At 6 wk of age, calves were subjected to a social test and a novel environment test. In the social test, all pair-housed calves (P and VP) had a shorter latency to sniff an unfamiliar calf than did individually housed calves (I, V, and T), whereas calves with physical contact (T, P, and VP) sniffed the unfamiliar calf for longer than calves on the remaining treatments (I and V). In the novel environment test, calves with physical contact (T, P, and VP) had a lower heart rate, and more of these calves vocalized during the test compared with calves without physical contact (I and V). No effect of treatment was found for clinical scores, levels of the 5 most common pathogens in feces, or in development of serum antibodies against the 3 most common respiratory pathogens. Calves housed individually are more fearful of unfamiliar calves than are pair-housed calves. Contrary to common belief, the allowance of physical contact and pair housing had no effects on the health of the calves.     

Analytical average throughput and delay estimations for LTE uplink cell edge users

Estimating average throughput and packet transmission delay for worst case scenario (cell edge users) is crucial for LTE cell planners in order to preserve strict QoS for delay sensitive applications. Cell planning techniques emphasize mostly on cell range (coverage) and throughput predictions but not on delay. Cell edge users mostly suffer from throughput reduction due to bad coverage and consequently unexpected uplink transmission delays. To estimate cell edge throughput a common practice on international literature is the use of simulation results. However simulations are never accurate since MAC scheduler is a vendor specific software implementation and not 3GPP explicitly specified. This paper skips simulations and proposes an IP transmission delay and average throughput analytical estimation using mathematical modeling based on probability delay analysis, thus offering to cell planners a useful tool for analytical estimation of uplink average IP transmission.     

Evaluation of non-linear strain paths using Generalized Forming Limit Concept and a modification of the Time Dependent Evaluation Method

The prediction of formability is one of the most important tasks in sheet metal forming process simulation. The common criterion for ductile fracture in industrial applications is the Forming Limit Diagram (FLD). This is only applicable for linear strain paths. However, in most industrial simulation cases non-linear strain paths occur. To resolve this problem, a phenomenological approach is introduced, the so-called Generalized Forming Limit Concept (GFLC). The GFLC enables prediction of localized necking on arbitrary non-linear strain paths. Another possibility is the use of the Time Dependent Evaluation Method (TDEM) within the simulation as a failure criteria. During the Numisheet Benchmark 1 (2014) a two-stage forming process was performed with three typical sheet materials (AA5182, DP600 and TRIP 780) and three different blank shapes. The task was to determinate the point in time and space of local instability. Therefore the strain path for the point of maximum local thinning is evaluated. To predict the start of local necking the Generalized Forming Limit Concept (GFLC), the Time Dependent Evaluation Method (TDEM) and the modified TDEM were applied. The results of the simulation are compared with the results of the Benchmark experiment.     

Implementing knowledge building: Analysis of a face‐to‐face discussion by grade‐four students

Abstract:

Researchers say that teachers can implement an educational innovation without adhering to the principles underpinning its design. Such principles may not adequately take typical classroom conditions into account. The goal of this study was to explore tensions between attempts to implement the principles underpinning knowledge building and the influence of contextual factors that compete for the teacher's attention. To this end, we discuss five excerpts from a discussion of the motion of spinning tops held by a class of Grade‐4 students, coming at the end of a five‐month implementation of knowledge building. Each excerpt is followed first by the teacher's perspective and then by the researcher's perspective. Our analysis highlights two tensions that constrain agency, arising from the students’ need for social development and their need to learn scientific concepts. We offer some suggestions for addressing these tensions.