The Impact of CASE on Software Development

Computer-aided software engineering ( CASE) is changing the way IS professionals develop information systems. This article demonstrates how traditional systems development methods are changing with automation, describes a new six-phase software development methodology— the CASE life cycle— designed to maximize the effective use of CASE technologies, and discusses how, organizations can make the transition to this new methodology.     

Study of a BGO calorimeter using electron and hadron beams from 1 to 50 GeV

A calorimeter of 25 bismuth germanate (BGO) crystals equipped with silicon photodiode readout has been tested at the CERN SPS in the energy range 1–50 GeV. The response for electrons has been shown to be linear in this energy range and the rms resolution obtained ( ) is approximately 1%, for E > 4 GeV. The electron/pion separation was found to be better than 1:500 in the energy range 1–20 GeV. Data on lateral and longitudinal shower development were compared with the results of a Monte Carlo simulation using the SLAC-EGS program and found to be in good agreement.     

Probing the thermal decomposition process of layered double hydroxides through in situ <Superscript>57</Superscript>Fe Mössbauer and in situ X-ray diffraction experiments

The thermal decomposition properties of Mg–Fe hydrotalcites were studied through in situ ⁵⁷Fe Mössbauer spectroscopy and in situ X-ray diffraction. Abrupt changes in the quadrupolar splitting measured in the Mössbauer spectra revealed a phase transition from the starting lamellar structure to a new crystalline arrangement. By analyzing the Mössbauer parameters we show that the material is highly disordered in the 300–400 °C temperature range. This hypothesis is confirmed by the X-ray results whose diffractograms indicated the collapse of the lamellar structure and the formation of a solid solution.     

On the stabilizing behavior of zirconia: A Combined experimental and theoretical study

Reactive zirconia powder was synthesized by the complexation of zirconium metal from zirconium hydroxide using a solution of 8-hydroxiquinoline. The kinetics of zirconia crystallization was followed by X-ray diffraction, scanning electron microscopy and surface area measured by the nitrogen adsorption/desorption technique. The results indicated that zirconia with a surface area as high as 100 m²/g can be obtained by this method after calcination at 500°C. Zirconia presents three polymorphic phases (monoclinic, tetragonal and cubic), which are reversibly interconversible. The cluster model Zr₄O₈ and Zr₄O₇ ⁺² was used for a theoretical study of the stabilization process. The ab initio RHF method was employed with the Gaussian94 program and the total energies and the energy gap of the different phases were calculated and compared with the experimental energy gap. The theoretical results show good reproducibility of the energy gap for zirconia.     

X-ray microfluorescence analysis of pigments in decorative paintings from the sarcophagus cartonnage of an Egyptian mummy

This work characterized the elemental composition of the pigments used in decorative paintings from the sarcophagus cartonnage fragments of an Egyptian mummy, using μXRF with Synchrotron Radiation. This female mummy (n.158) is considered one of the most important pieces of the National Museum (Rio de Janeiro, Brazil) because of its unconventional embalming with legs and arms swathed separately. The measurements were performed at the XRF beamline D09B of the Brazilian Synchrotron Light Laboratory (LNLS), using white beam and a Si(Li) detector with resolution of 165 eV at 5.9 keV. The elements found in the samples were: Si, S, Cl, K, Ca, Ti, Cr, Mn, Fe, Ni, Cu, Zn, As, Sr, Hg and Pb.     

Combined time and wavelength multiplexing technique of optical fiber grating sensor arrays using commercial OTDR equipment

The use of a commercial optical time domain reflectometry device for simultaneous wavelength and time domain multiplexing of fiber-optic Bragg grating sensors is proposed and demonstrated. The realization of such systems provides an inexpensive way of interrogating several hundreds of sensors in a single fiber. Strain resolution of 30 /spl mu/m/m over a strain measuring range of 0.5% was obtained.     

Tensile and flexural creep rupture tests on partially-damaged concrete specimens

Three series of novel tensile and flexural creep tests on partially-damaged concrete specimens were carried out in order to gain some insight into creep crack growth and failure of strain-softening materials. In the tests, each specimen was initially loaded to a given point in the descending branch and thus had a lower load-carrying capacity than that at the peak-point. Then, the specimen was unloaded and reloaded to sustain a load which was from 70% to 95% of its current load-carrying capacity. Experimental creep curves display a three-stage process, consisting of primary, secondary and tertiary stages, with a decreasing, constant and increasing creep rate, respectively. The secondary stage dominates the whole failure lifetime, whereas both the secondary and tertiary stages are important in terms of creep deformation. Failure life-time seems to be more sensitive to the change of load level in flexural tests rather than in tensile tests. The decrease in load-carrying capacity due to damage tends to result in a shorter failure lifetime and a lower critical load level for creep rupture. The descending branch of the static load-deflection or load-CMOD curve may be used as an envelope criterion for creep fracture.     

Multi-level simulation of metal-forming processes

The IBF has for some years made use of finite element programmes to solve metal-forming problems. In the course of this investigation, it has become evident that a problem-oriented adaptation of FEM simulation to the problem in hand is beneficial in terms of computation effort. The computation time for the process parameters is optimised in a multi-level simulation. At level 1 (global analysis) integral parameters such as the required force and required work are computed using a coarse FEM mesh. At level 2 (local analysis) an optimised number of elements is used to determine continuum mechanics parameters like stress, strain and temperature. Microscopic phenomena are simulated at level 3 (microscopic analysis), using special micro-material elements and thermodynamic models.     

Constructing candidate word lists using acoustically similar wordgroups

A method for identifying a set of candidate words that matches well with a given utterance is discussed. The method uses precomputed groups of acoustically similar words. Given a vocabulary, for each word a short list of words that are acoustically similar to it is computed. These groups are constructed using training utterances recorded by several speakers and used in an isolated utterance recognition system to construct candidate word lists during recognition. Experiments show that the correct word appears on the short list of candidate words constructed during recognition using this scheme over 98% of the time