CALCULATION ON TWO-PHASE FLOW TRANSIENTS AND THEIR EXPERIMENTAL RESEARCH

From basic equations of gas-liquid, solid-liquid, solid-gas two-phase flow, the calculating method on flow transients of two-phase flow is developed by means of characteristic method. As one example, a gas-liquid flow transient is calculated and it agrees well with the experimental result. It is shown that the method is satisfactory for engineering demand.     

硝酸铵的膨化机理研究

膨化硝酸铵是一种自敏化改性硝酸铵,由硝酸铵溶液在专用表面活性剂作用下,经真空强制析晶工艺制得.文中研究了膨化硝酸铵制备的膨化过程和专用表面活性剂的作用,结果表明:在真空和表面活性剂作用下,硝酸铵溶液由不饱和状态至饱和状态,进而达到过饱和状态,最终导致硝酸铵的快速结晶和体系的膨胀.在真空干燥过程中,形成中心空穴、微细孔道和裂缝,它们使膨化硝酸铵的起爆感度提高;专用表面活性剂具有降低硝酸铵溶液表面张力、发泡剂和加快结晶成核的作用.     

Comparisons of PWM and one-cycle control for power amplifier with multilevel converter

Based on the concepts of cascade multilevel converters and one-cycle technique, comparisons are conducted to characterize the distortion of the pulsewidth modulation (PWM) and one-cycle control methods that were applied to converters. Simulation results for the different control schemes are obtained in PSIM software initially to see the effect of one-cycle control different from that of PWM control. Through the comparisons, the advantages and disadvantages are identified for each method. The one-cycle scheme is better than PWM control in reducing undesirable harmonics and tracing dynamic waveforms. Simulation and experimental results are also provided to verify the conclusions.     

玻璃钢包扎在煤气管道加强上的应用

介绍了玻璃钢包扎煤气管道的施工材料、施工流程及要点，指出了此方法应用在煤气管道加强上的优点。     

缓冲层对氮化镓二维生长的影响

报道了在射频等离子体（RF-Plasma)辅助的分子束外延（MBE）技术中，使用白宝石（0001）衬底，采用低温缓冲层工艺外延氮化镓（GaN)。通过原子力显微镜（AFM）的表面形貌比较及X射线双晶衍射（XRD）ω扫描摇摆曲线的分析，讨论了低温缓冲层成核机理及缓冲层生长温度与形成准二维生长的关系，确立了缓冲层的三维成核，准二维生长的生长机理，并在此基础上实现了氮化镓外延层更好地二维生长，进一步提高了氮化镓外延层的晶体质量。     

全20CrMnTi表面激光重熔的组织与性能研究

本文对激光重熔20CrMnTi材料表明改性层显微组织分布特征、表面硬度分布规律以及残余应力状态作了研究,结果表明,表面改性层由熔融层、相变硬化层及过渡层组成,且材料表面显微硬度得到大幅度提高,表面硬度达到HV841,约提高4倍。硬化层深度约1mm。残余应力测试得出最大残余应力出现在熔凝带中心,表现为压应力。随着离中心距离的增大,残余应力逐步降低,到熔化带边缘,表现为低幅值压应力;而熔池的外边缘应力在热影响区则转变为拉应力状态。     

激光远距作用的机制与效应

本文定量分析激光远距作用的机理并对它们在治癌中的作用作简要的论述。     

汉白玉废料制备球形纳米碳酸钙的研究

将汉白玉废料通过高温煅烧分解得到氧化钙,再用氯化铵循环液溶解氧化钙制得碱性氯化钙溶液,除去其中的Mg、Fe等杂质得到氯化钙精制溶液,利用化学方法合成得到碳酸钙粉体.用X射线衍射(XRD)、扫描电镜(SEM)及激光粒度分析仪、白度仪对碳酸钙产品的晶相组成、形貌、粒度分布、白度及化学组成进行了分析,所得产品为纯度达98.5%以上、白度达97%以上、平均粒度为80nm左右的球形纳米级碳酸钙.并对碳化反应速率及合成球形纳米碳酸钙的影响因素进行了分析.实验中循环使用NH4Cl,氨的排放量小,减少了环境污染.     

百色水利枢纽表孔弧门液压启闭机设计

介绍百色水利枢纽工程溢流坝表孔弧形工作闸门的液压启闭机的结构布置特点以及设计中采用的新方法、新材料.     

YAG：Ce Phosphors for WLED via Nano-Pesudoboehmite Sol-Gel Route

The sub-micron sized YAG ： Ce phosphors were synthesized via a modified sol-gel method by peptizing nano-pesudoboehmite particulate. It is found that YAG phase from the dried gel powders appears at 1000 ℃ then the pure YAG phase exists at a relatively lower sintering temperature of 1400 ℃. The smaller sizes of phosphors in the ranges of 1 - 3 μm are obtained due to the contribution of seeding effects of nano-sized alumina particles to strengthen each step of the processes. Both the excitation and emission spectra of photoluminescence of the phosphor obtained at 1400 ℃ meet well with the spectroscopic requirements of the WLED phosphors.