Design of novel compact anti-stiction and low insertion loss RF MEMS switch

A novel torsional RF MEMS capacitive switch design on silicon substrate is presented. The optimized switch topology such as reduction in up-state capacitance results in insertion loss better than ?0.1 dB till 20 GHz. Off to on state capacitance ratio is also improved by 18 fold and isolation is better than ?43 dB at 9.5 GHz. The achieved on state return loss is ?38 dB as compared to ?21 dB at 9.5 GHz. An optimized reduction in contact area and use of floating metal layer increases the switching speed from 56 to 46 μsec. It also increases the switch reliability by alleviating the stiction.     

Preparation of NiAl2O4/SiO2 and Co2+-Doped NiAl2O4/SiO2 Nanocomposites by the Sol–Gel Route

NiAl₂O₄/SiO₂ and Co²⁺-doped NiAl₂O₄/SiO₂ nanocomposite materials of compositions 5% NiO – 6% Al₂O₃– 89% SiO₂ and 0.2% CoO – 4.8% NiO – 6% Al₂O₃– 89% SiO₂, respectively, were prepared by a sol–gel process. NiAl₂O₄ and cobalt-doped NiAl₂O₄ nanocrystals were grown in a SiO₂ amorphous matrix at around 1073 K by heating the dried gels from 333 to 1173 K at the rate of 1 K/min. The formations of NiAl₂O₄ and cobalt-doped NiAl₂O₄ nanocrystals in SiO₂ amorphous matrix were confirmed through X-ray powder diffraction, Fourier transform infrared spectroscopy, differential scanning calorimeter, transmission electron microscopy (TEM), and optical absorption spectroscopy techniques. The TEM images revealed the uniform distribution of NiAl₂O₄ and cobalt-doped NiAl₂O₄ nanocrystals in the amorphous SiO₂ matrix and the size was found to be ∼5–8 nm.     

A novel layered Li [Li0.12NizMg0.32−zMn0.56]O2 cathode material for lithium-ion batteries

Layered Li[Li_0.12Ni_zMg_0.32−zMn_0.56]O₂ oxide cathodes containing lithium atoms in the transition metal layers were synthesized and characterized using X-ray diffraction (XRD), galvanostatic cycling, and differential scanning calorimetry (DSC). The Li[Li_0.12Ni_zMg_0.32−zMn_0.56]O₂ cathodes deliver a specific discharge capacity of about 190 mAh/g at room temperature and 236 mAh/g at 55 °C when cycled between 2.7 and 4.6 V versus Li/Li⁺. Excellent capacity retention and smooth potential profiles at room and elevated temperatures over extended cycles suggest that this material does not convert into a spinel structure.     

Viscosity of Porous Glasses

Viscosity of porous glasses has been derived from the elastic stress analysis, using the viscous analogy. Viscosity as a function of porosity has been estimated for spherical as well as for arbitrary pore geometry. Since the pore geometry changes during sintering, a shape factor that varies with pore geometry has been considered to predict the viscosity–porosity relationship. Viscosity as a function of porosity was measured on cordierite-type glass by isothermal sinter-forging experiments and data showed good agreement with the analysis. Experimental data from literature on viscosity as a function of porosity on two other glasses also show good agreement with the analysis.     

Tensile properties and morphology of S2Cl2 treated PVC-g-butly rubber

Summary We have grafted butyl rubber from PVC under a variety of conditions. The physical-mechanical properties of these graft copolymers have been examined both before and after extraction with hexane of the ungrafted butyl rubber. We have found a significant increase in the tensile strength of these materials upon S₂Cl₂ treatment (curing) in THF solution. This increase was observed even with unextracted copolymers. Electron micrograph studies suggest that curing causes an aggregation of the butyl rubber segments into crosslinked domains.     

Limits of compensation in a failed antenna array

In large antenna arrays, the possibility of occurrence of faults in some of the radiating elements cannot be precluded at all times. In such situations, the radiation pattern of the array gets distorted, mostly with an increase in sidelobe level and decrease in gain. Although it is not possible to restore the pattern fully by rearranging the excitations of the functioning elements, compensation methods have been reported in the literature for restoring one performance parameter of the array and making a trade‐off on some other parameter. In this article, we have made a study on the tolerance level of this compensation process. One part of the study deals with the thinning in the failed array, that is, to find a limit on the minimum number of functioning elements of the array that can restore the digital beamforming of the failed array. The second part of study deals with finding the maximum number of element failures that can be compensated. The study was carried out by optimizing the amplitude excitations of the failed array. Instead of classical optimization techniques, particle swarm optimization was used for the compensation process. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:635–645, 2014.     

Performance of a magnesium–lithium alloy as an anode for magnesium batteries

In this work, we describe an evaluation of an Mg–Li alloy (Li: 13 wt %) for possible use in magnesium primary reserve batteries. Higher OCP for the Mg–Li alloy have been observed in 2 M MgCl₂ and MgBr₂ electrolyte. The corrosion rate of the Mg–Li alloy is found to be in the order: MgCl₂ < Mg(COOCH₃)₂ < MgSO₄ < MgBr₂ < Mg(ClO₄)₂. Mg–Li alloys exhibit higher (81%) anodic efficiencies even when the current density is increased to 8.6 mA cm ^–2. It has been observed that Mg–Li/MgCl₂/CuO cells offer higher operating voltage and capacity than those with the conventionally used Mg–Al alloy.     

Targeting and design of water networks for fixed flowrate and fixed contaminant load operations

Water-using processes are typically modeled as either fixed flowrate operations or fixed contaminant load operations. A new method for targeting the minimum freshwater and pinch in a single-contaminant water network is proposed, which can be applied to both kinds of operations. The method consists of plotting separate source and demand composites with flowrate as the horizontal axis and contaminant load unusually as the vertical axis. It is elegant, non-iterative, and can handle hybrid problems where both kinds of operations coexist.To design minimum freshwater networks for fixed flowrate problems, an algorithm is presented based on a newly developed principle of nearest neighbors. The principle simply states that the source streams to be chosen to satisfy a particular water demand must be the nearest available neighbors in terms of contaminant concentration.To design minimum freshwater networks for fixed contaminant load problems, the nearest neighbors algorithm is applied to process units that lie across the pinch. Units that lie entirely on one side of the pinch are satisfied by the cleanest source available on that side of the pinch. In other words, below-pinch units are satisfied by freshwater and above-pinch units are satisfied by the cleanest available stream above the pinch. Designs based on this methodology, apart from meeting the minimum freshwater target, also minimize the water flowing through the process units resulting in reduced network capital cost.     

Performance evaluation of saponin over other organic acid and tap water for removal of chromium in tannery sludge by electrokinetic enhancement

The performance of Saponin over different electrolyte-mediated electrokinetic (EK) process for removal of Cr(III) from tannery sludge was assessed. Saponin exhibited maximum Cr(III) removal efficiency, i.e. 67.6–80.75% as compared to other groups of processing fluids. The possible mechanistic approach for the highest removal efficiency of saponin over other electrolytes may be attributed to synchronized effect of micelle formation and subsequent complexation and sorption of chromium ions. The highest electroosmotic flow rate of saponin indicated low electroosmotic resistance during EK process, which validates the observed trend. Therefore, saponin can be considered as a promising electrolyte for EK treatment of tannery sludge.

Abbreviation: CA: Citric acid; LA: lactic acid; OA: oxalic acid; BOD: biochemical oxygen demand; COD: chemical oxygen demand; EK: electokinetic.     

Mass transfer between solid particles and liquid in a three phase fluidized bed

Particle-liquid mass transfer in a co-current three-phase fluidized bed of glass beads, water and air was studied with two measurement techniques. Both techniques measured the weight loss of a few particles coated with benzoic acid in a bed of inert glass beads. The effects of liquid and gas velocities, gas distribution and surface active agents on particle-liquid mass transfer in a three-phase fluidized bed were thus determined. In the absence of surface active agents in the liquid, particle-liquid mass transfer rates in a three-phase fluidized bed were up to 30% higher than in the corresponding liquid fluidized bed. When surface active agents were added to the liquid, the particle-liquid mass transfer rate was increased by up to about 100% in the three-phase fluidized bed, relative to the liquid fluidized bed. The particle-liquid mass transfer coefficient was found to be inversely proportional to the liquid hold-up in the three-phase fluidized bed.