DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

Predicting visual similarity between colour palettes

This work is concerned with the prediction of visual colour difference between pairs of palettes. In this study, the palettes contained five colours arranged in a horizontal row. A total of 95 pairs of palettes were rated for visual difference by 20 participants. The colour difference between the palettes was predicted using two algorithms, each based on one of six colour-difference formulae. The best performance (r² = 0.86 and STRESS = 16.9) was obtained using the minimum colour-difference algorithm (MICDM) using the CIEDE2000 equation with a lightness weighing of 2. There was some evidence that the order (or arrangement) of the colours in the palettes was a factor affecting the visual colour differences although the MICDM algorithm does not take order into account. Application of this algorithm is intended for digital design workflows where colour palettes are generated automatically using machine learning and for comparing palettes obtained from psychophysical studies to explore, for example, the effect of culture, age, or gender on colour associations.     

A dense and compact laser cladding layer with solid metallurgical bonding significantly improved corrosion resistance of Mg alloy for engineering applications

Although Mg alloy attracts great attention for engineering applications because of high specific strength and low density, low corrosion resistance limits its extensive use. In this study, Mg–Al–Zn–Mn alloy was treated via a laser cladding process to generate a dense and compact laser cladding layer with solid metallurgical bonding on the substrate for improving corrosion resistance, effectively hindering the corrosion pervasion into Mg alloy. The corrosion current density declined from 103 μA/cm² for Mg alloy to 13 μA/cm² for the laser cladding layer in NaCl aqueous solution. Moreover, the laser cladding layer was slightly corroded in comparison with Mg alloy in NaCl aqueous solution. Besides, the microhardness of the cladding layer reached a mean value of 170.5 HV, 3.1 times of Mg alloy (56.8 HV) due to the in situ formation of hardening intermetallic phases. Wear resistance of laser cladding layer was also obviously improved. These results demonstrated that the laser cladding layer obviously enhanced anticorrosion property of Mg alloy for engineering applications.     

Cover Image

The cover image is based on the Research Article Observer‐Based Cooperative Distributed Fault‐tolerant Model Predictive Control with Imperfect Network Communication and Asynchronous Measurements by Guannan Xiao and Fei Liu, https://doi.org/10.1002/rnc.4994 .

     

Anchoring single Pt atoms on hollow Ag3VO4 spheres for improved activity towards photocatalytic H2 evolution reaction

The high cost of noble metal catalysts has been a great bottleneck for the catalyst industry. Using the noble metal at a single-atom level for catalytic applications could dramatically decrease the cost. The impacts of single Pt atoms on the photocatalytic performance of Ag₃VO₄ have been investigated and reported. In this report, single Pt atoms were anchored on the surface of Ag₃VO₄ (AVO) as a cocatalyst, and the resultant composite photocatalyst has been studied for photocatalytic H₂ production from water driven by visible light. The as-prepared AVO particles are hollow nanospheres in the monoclinic phase with a bandgap of 2.20 eV. The light absorption edge of AVO/Pt is slightly red-shifted compared to that of the pristine AVO, indicating more visible light absorption of AVO/Pt. The XPS peaks of Ag, V, and Pt exhibit a significant shift after AVO and Pt get into contact, suggesting the strong interaction between the surface Ag and V atoms, and single Pt atoms. After 3-h illumination, the photocatalytic H₂ evolution amount from AVO/Pt is improved up to 1400 μmol, which is 2.8 times that on the bare AVO. Such efficient photocatalytic H₂ evolution on AVO/Pt is still maintained after five reaction cycles. The better photocatalytic performance of AVO/Pt has been attributed to the more efficient visible light utilization and the lower interfacial charge transfer resistance, as demonstrated in the DRS and EIS spectra. The presence of the surface Pt atoms also leads to a higher amount of reactive radicals, which could efficiently promote the surface redox reactions.     

A first-principles investigation on mechanical and metallic properties of titanium carbides under pressure

The titanium carbides are potential candidates to achieve both high hardness and refractory property. We carried out a structural search for titanium carbides at three pressures of 0 GPa, 30 GPa and 50 GPa. A phase diagram of the Ti-C system at 0 K was obtained by elucidating formation enthalpies as a function of compositions, and their mechanical and metallic properties of titanium carbides were investigated systematically. We also discussed the relation of titanium concentration to the both mechanical and metallic properties of titanium carbides. It has been found that the average valence electron density and tractility improved at higher concentrations of titanium, while the degree of covalent bonding directionality decreased. To this effect, the hardness of titanium carbide decreases as the content of titanium increases. Our results indicated that the titanium content significantly affected the metallic properties of the Ti-C system.     

基于投影寻踪的径向基函数网络在参考腾发量预测中的应用

径向基函数网络(RBFN)已广泛应用于参考腾发量预测等领域，但常用的K均值聚类和自组织特征映射等方法在求取径向基函数网络隐层节点中心时存在较大不足。针对这一问题，本文引入投影寻踪方法，在投影降维的基础上实现对大量高维数据的聚类，建立了基于投影寻踪的径向基函数网络模型，并将该模型应用于山西潇河灌区参考腾发量的预测，研究了不同气象因子输入对参考腾发量预测精度的影响。结果表明，基于投影寻踪的径向基函数网络具有较强的适用性，只需使用最高温度、最低温度、日照时数和旬序数作为输入因子，就能以较高的精度预测参考腾发量。     

Al2O3陶瓷激光铣削试验研究

采用Nd∶YAG脉冲激光器对Al2 O3陶瓷进行铣削加工试验。系统研究了工艺参数对铣削量和铣削面质量的影响规律 ,并利用优化的铣削工艺对Al2 O3陶瓷进行多种形状的铣削加工。     

随机库存分配问题的一种求解方法

讨论了在VMI管理思想下对具有随机需求特性的多客户库存分配问题 ,重点论述了有效近似算法的设计过程 ,最后基于一组模拟数据给出了一个算例。