Reply to comments on “Error rate performance of theprojection code”

The authors reply to the comments by Koppelaar and Tolhuizen (see ibid. vol.46, no.9, p.573, 1998). They state that the optimum choice of the slopes used to perform the encoding process in a projection code always results in maximizing the minimum Hamming distance so that d=2 ^r     

Two-level optimal output feedback stabilizer design

The paper addresses the design of two-level power system stabilizers using an optimal reduced order model whose state variables are torque angles and speeds. The reduced order model retains their physical meaning and is used to design a two-level linear feedback controller that takes into account the realities and constraints of electrical power systems. The two-level control strategy is used, and a global control signal is generated from the output variables to minimize the effect of interactions. The effectiveness of this controller is evaluated and a multimachine system is given as an example to illustrate the advantages of the proposed method. Responses of the system with a two-level scheme and an optimal reduced order scheme are included for comparative analysis.     

The investigation of 32P wire for catheter-based endovascular irradiation

The dose distribution from a 32P source has been measured and calculated in order to evaluate its application in endovascular irradiation. The source dimension was 27 mm in length and 0.3 mm in diameter and was embedded in the end of a Ni-Ti wire. Dose measurements were performed using radiochromic film in several specially designed tissue equivalent phantoms. Loevinger's point dose kernel was used for the calculation. The approximate dose rate at a radial distance of 1.5 mm from the center of the source was found to be 6.75 cGy/s per GBq (0.25 cGy/s per mCi), which allows the delivery of a therapeutic dose in a short time interval with a satisfactory homogeneity without stepping the source. However, the dose rate falls off almost exponentially along the radial distance. Therefore it may not be suitable for treating large diameter vessel from a centrally located source. The effect of a curved 32P wire source on the radial dose distribution was also investigated. The results showed that for a maximum bend of 180 degrees the dose rate was increased by as much as 20% along the inner radial distance but decreased by as much as 20% along the outer radial distance compared to the dose along a straight wire. However, for curvatures normally encountered in a clinical situation, the dose rate was changed less than 5%.     

钢的连铸用保护渣的表征

在钢的连铸过程中,结晶器保护渣的性质强烈地影响着铸造的行为、钢的质量、以及连铸工艺的环境.本研究采用高温显微技术来研究保护渣的熔化行为,采用液滴测试方法来测定保护渣的熔化速率.结果表明:自由碳是控制保护渣熔化行为的主要因素.熔化速率随碳的反应能力的增加而增加,随着碳含量的减少而增加.     

高合金铁基烧结材料在轧钢导位中的应用研究

本文研究了高合金铁基烧结材料在轧钢导位中的应用。实验表明,通过粉末冶金液相烧结技术,可以获得具有优良综合性能的制品,材料密度ρ≥7.5 g/cm3,硬度≥55 HRC,抗弯强度≥1 000 MPa,冲击韧度αk≥3.9 J/cm2,满足了轧钢导位辊的工作要求。材料利用率可达95%以上、降低了制备成本。使用寿命是普通轧辊寿命的3~6倍,适用于线材和小型型材的轧钢生产。     

Cloud analysis by modeling the integration of heterogeneous satellite data and imaging

This paper presents a computer-aided cloud-analysis approach by effectively modeling the integration of heterogeneous satellite-observed data and remote sensing images. First, automatic cloud detection and tracking methods are proposed to identify the georeferenced cloud objects in satellite remote sensing images. Then, a data integration modeling mechanism is designed to collect meaningful properties of those detected clouds by integrating the heterogeneous satellite-observed data and imaging into a unified cloud database. Finally, based on the integrated global data schema, a two-phase data mining method employing the decision tree algorithm is implemented to analyze and forecast the meteorological activities of all the cloud objects. Experimental results have shown that the proposed data integration model can effectively extract and synthesize all the useful information from heterogeneous data sources to generate a unified view of knowledge, on the basis of which the evolvement trends of clouds can be analyzed properly.     

Performance evaluation of dynamically linearized and kinematically redundant planar manipulators

The objective of this research is to investigate the feasibility of a theoretical development which could lead to advanced manipulator concepts offering fast dynamic and control features. Specifically, the application of “dynamic linearization” to a kinematically redundant planar manipulator is studied. In comparing such a manipulator with a standard non-linear, non-redundant design it is shown that in addition to the expected merits in linearity, dexterity, and computational simplicity, savings in actuator energy consumption can also be realized using a relative simple trajectory optimization scheme.