Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

Climatic solar roof: an ecological alternative to heat dissipation in buildings

A new system based on the harnessing of solar and wind power is presented for heat dissipation in air conditioning facilities. The innovation offered by the new system is the integration of two well-known subsystems: a cooling tower and a solar chimney which increases the air flow without the use of electric power. The system is described and presented together with a model for its study. The field data acquired from the prototype built in southern Spain establishes the actual potential of the system, which provides a new approach to a sustainable technological development.     

Parametric inference for step-stress models

Applications of the additive accumulation of damages (AAD) or the accelerated failure time (AFT) and the proportional hazards (PH) models in accelerated life testing with step-stresses are discussed. A new model including AAD and PH models is proposed. It is more reasonable than the PH model and wider then the AAD model. Constructing the maximum likelihood function is discussed     

Effect of Thermohydrogen Treatment on the Structure and Properties of Titanium Alloy Castings

Metal Science and Heat Treatment -     

Analysis of burn-in time using the general law of reliability

Empirical lifetime distributions sometimes have a bathtub-shaped failure rate. This paper deals with some models having a bathtub-shaped failure rate. The root-mean-square criterion is proposed for selection of the best model. Besides two criteria of optimum burn-in time are proposed. The comparison of some models with the general law of reliability is given to determine a burn-in time in a number of examples.     

Experience in High-Temperature Thermomechanical Treatment with Helical Reduction in the Production of Axisymmetric Parts

Metal Science and Heat Treatment -     

A multi-agent decision support system for stock trading

A distributed problem solving system can be characterized as a group of individual cooperating agents running to solve common problems. As dynamic application domains continue to grow in scale and complexity, it becomes more difficult to control the purposeful behavior of agents, especially when unexpected events may occur. This article presents an information and knowledge exchange framework to support distributed problem solving. From the application viewpoint the article concentrates on the stock trading domain; however, many presented solutions can be extended to other dynamic domains. It addresses two important issues: how individual agents should be interconnected so that their resources are efficiently used and their goals accomplished effectively; and how information and knowledge transfer should take place among the agents to allow them to respond successfully to user requests and unexpected external situations. The article introduces an architecture, the MASST system architecture, which supports dynamic information and knowledge exchange among the cooperating agents. The architecture uses a dynamic blackboard as an interagent communication paradigm to facilitate factual data, business rule, and command exchange between cooperating MASST agents. The critical components of the MASST architecture have been implemented and tested in the stock trading domain, and have proven to be a viable solution for distributed problem solving based on cooperating agents     

Mixed Mode VLSI Implementation of a Neural Associative Memory

A mixed mode digital/analog special purpose VLSI hardware implementation of an associative memory with neural architecture is presented. The memory concept is based on a matrix architecture with binary storage elements holding the connection weights. To enhance the processing speed analog circuit techniques are applied to implement the algorithm for the association. To keep the memory density as high as possible two design strategies are considered. First, the number of transistors per storage element is kept to a minimum. In this paper a circuit technique that uses a single 6-transistor cell for weight storage and analog signal processing is proposed. Second, the device precision has been chosen to a moderate level to save area as much as possible. Since device mismatch limits the performance of analog circuits, the impact of device precision on the circuit performance is explicitly discussed. It is shown that the device precision limits the number of rows activated in parallel. Since the input vector as well as the output vector are considered to be sparsely coded it is concluded, that even for large matrices the proposed circuit technique is appropriate and ultra large scale integration with a large number of connection weights is feasible.     

New bounds for the Marcum Q-function

New bounds are proposed for the Marcum Q-function, which is defined by an integral expression where the 0th-order modified Bessel function appears. The proposed bounds are derived by suitable approximations of the 0th-order modified Bessel function in the integration region of the Marcum Q-function. They prove to be very tight and outperform bounds previously proposed in the literature. In particular, the proposed bounds are noticeably good for large values of the parameters of the Marcum Q-function, where previously introduced bounds fail and where exact computation of the function becomes critical due to numerical problems