Monitoring systems and determination of actual fatigue usage

At GKN, fatigue monitoring of important components has been conducted since 1979. The monitoring methods depend on the mechanisms of damage; quasi-static loads are regarded as well as dynamic loads. The components were selected for monitoring on the basis of a system analysis. The data resulting from monitoring are used to optimise operation mode steadily. Experience shows that the use of monitoring data as input for fatigue assessment is the most realistic and cost-effective way. This fatigue assessment uses global and local sensitivity studies to evaluate the load-stress relation for each component. These relations can be programmed to produce stress vs. time curves. These are processed according to ASME rules to give a realistic fatigue usage.     

Nitric oxide reduction and carbon monoxide oxidation over carbon-supported copper-chromium catalysts

Carbon supported copper-chromium catalysts are shown to be very active for both the reduction of nitric oxide with carbon monoxide and the oxidation of carbon monoxide with oxygen. Mixed copper-chromium oxide active phases have good activity in the simultaneous removal of nitric oxide and carbon monoxide from exhaust gases. The influence of several catalyst variables has been investigated. The activity per volume of catalyst increases with increasing loading, while the intrinsic activity shows a maximum around C/M=100−50. An optimum catalyst for nitric oxide reduction and carbon monoxide oxidation has a copper/chromium ratio of 2/1. The apparent activation energy for the carbon monoxide oxidation over carbon supported copper-chromium catalysts is 77 kJ/mol, suggesting that the Cu---O bond rupture is the rate-limiting process. The reduction of nitric oxide takes place at higher temperatures. Since all catalysts have a low selectivity for molecular nitrogen formation at lower temperatures, the dissociation of nitric oxide is probably rate determining, resulting in a slightly reduced catalyst system. In an excess of carbon monoxide the reaction is first-order in nitric oxide and zero-order in carbon monoxide. Moisture inhibits the reaction by reversible competitive adsorption, whereas carbon dioxide does not. Oxygen completely inhibits the reduction of nitric oxide due to the more rapid reoxidation of the catalytic sites compared to nitric oxide. Therefore, the reduction of nitric oxide takes place only when all oxygen has been converted and, hence, is shifted to higher temperatures. As a possible consequence, the production of nitrous oxide is reduced. Nitric oxide and molecular oxygen react preferentially with carbon monoxide, so, in an excess of oxidizing component, gasification of the carbon support occurs at higher temperatures after carbon monoxide has been completely consumed.     

The evolution of custom microarray manufacture

Given the enormous size of the genome and that there are potentially many other types of measurements we need to do to understand it, it has become necessary to pick and choose one's targets to measure because it is still impossible to evaluate the entire genome all at once. What has emerged is a need to have rapidly customizable microarrays. There are two dominant methods to accomplish custom microarray synthesis, Affymetrix-like microarrays manufactured using light projection rather than semiconductor-like masks used by Affymetrix to mass manufacture their GeneChip/sup TM/ arrays now, or the ink-jet printing method employed by Agilent. The manufacture of these custom Affymetrix-like microarrays can now be done on a digital optical chemistry (DOC) machine developed at the University of Texas Southwestern Medical Center, and this method offers much higher feature numbers and feature density than is possible with ink-jet printed arrays. On a microarray, each feature contains a single genetic measurement. The initial DOC prototype has been described in several publications, but that has now led to a second-generation machine. This machine reliably produces a number of arrays daily, has been deployed against a number of biomedical questions, is being used in new ways and has also led to a number of spin-off technologies.     

Measurements of single chain form factors by small-angle neutron scattering from polystyrene blends containing high concentrations of labelled molecules

A series of small angle neutron scattering measurements on blends of normal polystyrene (PSH) and labelled (deuterated) polystyrene (PSD) have been made with concentrations of PSD from 5 to 50 mol %. It is shown that the single chain form factor of the polymer in bulk can be obtained from a single concentration measurement for any concentration of labelled molecules, providing the molecular weights of the parent and labelled molecules are the same and the molecular weight distributions are narrow.     

Functional Properties and Food Applications of Rapeseed Protein Concentrate

Rapeseed protein concentrate (RC), prepared with 2% hexameta-phosphate, was tested for its functionality and performance in some foods. The RC had good nitrogen solubility, fat absorption, emulsification, and whipping capacities but poor water absorption and gelling properties. It increased the emulsion stability, and protein but lowered the fat content of wieners. It also increased the cooking yield, reduced the shrinkage and tenderized meat patties. Results were similar to soybean isolate except for the poorer color and flavor. The cooking yield of RC supplemented wieners was less than the all-meat control and soybean-supplemented wieners. A 9% RC dispersion mixed with an equal volume of eggwhite produced a meringue of comparable stability and texture to that of eggwhite alone.     

Attraction of moth species of Tortricidae,Gelechiidae, Geometridae,Drepanidae, Pyralidae,and Gracillariidae families to field traps baited with conjugated dienes

Field surveys of a series of conjugated diunsaturated straight-chain primary alcohols, acetates, and aldehydes (dienes), including the 3,5-dode-cadienyl, 8,10-dodecadienyl, 3,5-tetradecadienyl, 8,10-tetradecadienyl, 9,11-tetradecadienyl, and 10,12-tetradecadienyl primary alcohols, acetates, and most aldehydes, and the related monounsaturated straight-chain primary alcohols, acetates, and aldehydes (monoenes), including the 3-dodecadienyl alcohol and acetates, attracted the following species from the title families. Diene attractants have been demonstrated for at least onePhyllonorycter sp.,Chionodes lugubrella (Fabr.),Leptostales ferruminaria (Zell.),Drepana bilineata (Pack.),Pyrausta fodinalis (Led.),Notocelia purpurissatana Heinr.,Phaneta alterana Heinr. Monoene attractants were demonstrated forHedya separatana (Kft.),Cydia fletcherana (Kft.),Barbara mappana Free.,Ancylis burgessiana (Zell.),Ancylis nubeculana Clem.,Evippe prunifoliella Cham.,Phlyctaenia coronata tertialis (Gn.), aChionodes sp., a Gelechiidae sp., and an unidentifiedPhyllonorycter sp. Replicated field experiments showed attraction-inhibition relationships for most species. Electroantennagram data are presented forLeptostales ferruminaria andDrepana bilineata.     

Polymeric schiff's base chelates and their precursors 8a), some cobalt chelates as catalysts for the isomerization of quadrycyclane to norbornadiene

Summary Starting with Z-2, 3-diamino-2-butenedinitrile as diamine component the synthesis of the low molecular N,N,O,O-chelate 3.Co and its ligand 3 is optimized. An easy synthesis of the chelate 8.Co covalently bound on macroreticular resins is presented. The chelates 8.Co are the most active heterogenous catalysts for the valence isomerization of quadricyclane to norbornadiene today.     

Interdisciplinary research: roles for self-organization

No generally accepted principles and guidelines currently exist to help engineers design local interaction mechanisms that result in a desired global behavior. However, several communities have developed ways of approaching this problem in the context of niched application areas. Because the ideas underlying these approaches are often obscured or underemphasized in technical papers, the authors review the role of self-organization in their work. They provide a better picture of the status of the emerging field of self-organizing systems or autonomic computing.