DEPOSITION OF A FINE POWDER IN HORIZONTAL PIPELINES AND BENDS

The deposition of a very fine powder in a horizontal, lean-phase pneumatic conveying conduit containing a 90° bend has been studied experimentally. The total deposition and the deposition pattern were studied as a function of superficial gas velocity, solids loading and bend geometry: one sharp and three smooth bends of different radii of curvature were used. Most deposition was seen in the sharp bend, while in the smooth bends the deposition did not vary much with radius of curvature. The deposition decreased significantly with increasing superficial gas velocity. The experimental results were compared with CFD simulations of the flow field. The observations are consistent with the notion of deposition in regions with low near-wall gas velocity, indicating that models for deposition should be sought in considerations of the deposit stability for this type of system.     

Polymerization of olefins through heterogeneous catalysis X: Modeling of particle growth and morphology

The development of a detailed model describing particle growth in olefin copolymerization systems is presented. The Multigrain Model considers in detail monomer sorption, mass transfer, and changing porosity within the growing particle, as well as heat and mass transfer across the external film of the particle. The model predicts catalyst performance, including polymerization rates and particle morphology, in different reactor media without parameter adjustment. Internal void fractions are calculated through an examination of the relative growth rates within the growing particle. The model is used to examine the effects of mass transfer limitations, prepolymerization, and nonuniform metal distribution on the particle growth process. Model predictions of morphology show the same trends as observed experimentally.     

Effect of Boehmite Alumina Nanofiller Incorporation on the Morphology and Thermal Properties of Functionalized Poly(propylene)/Polyamide 12 Blends

A composite of boehmite alumina nanoparticles and a PP/PA12 blend is prepared. WAXD and SEM suggest that a low filler loading enhances the coalescence of PA12, whereas a higher loading reverses the situation. DSC, DMA and TGA reveal that the final properties of the blend composites such as crystallization temperatures, flexural storage moduli, or thermal degradation temperatures improve with increasing nanoparticle loading. The data are compared with the neat polymers and the compatibilized blend, and the results show that the compatibility increases only at high nanoparticle loading, and most of the thermal properties improve with increasing nanoparticle content in the blends. The presence of interfacial interactions between the polymer matrices and the filler was confirmed via FTIR.

     

Synthesis,aggregation and adsorption behaviour of a thermoresponsive pentablock copolymer

Poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) (PEO–PPO–PEO) triblock copolymer (Pluronic F127) was modified by introducing poly(N‐isopropylacrylamide) (PNIPAM) at both the PEO ends, and the pentablock copolymer (PNIPAM₄₁–F127–PNIPAM₄₁, PN41) so prepared was characterized using gel permeation chromatography and ¹H NMR spectroscopy. The degree of polymerization of NIPAM blocks at the two ends was 41. The solution behaviour and microstructure of PN41 aggregates in water were examined using UV–visible spectroscopy, micro‐differential scanning calorimetry and small‐angle neutron scattering (SANS) and compared with F127. Two lower critical solution temperatures (LCSTs) were observed for the pentablock copolymer, corresponding to PPO and PNIPAM blocks, respectively. The adsorption of PN41 on thiol‐grafted hydrophobic gold surfaces at various temperatures was investigated using a quartz crystal microbalance. It was found that the adsorption behaviour and mechanism of PN41 were mainly determined by the interactions of the pentablock copolymers with different chain conformations in dilute aqueous solutions at various temperatures. SANS measurements were used to determine the temperature‐dependent structural evolution of polymer micelles in aqueous solution. A NOESY study revealed that above the LSCT of PNIPAM, the interaction of PPO and PNIPAM protons increases and the distance between PPO and PNIPAM decreases. © 2019 Society of Chemical Industry     

Supramolecular Poly(cyclotriphosphazene) Functionalized Graphene Oxide/Polypropylene Composites with Simultaneously Improved Thermal Stability,Flame Retardancy,and Viscoelastic Properties

A novel crosslinkable supramolecular poly(cyclotriphosphazene) functionalized graphene oxide (FGO) is synthesized and melt‐processed with polypropylene (PP), which results in a PP composite with simultaneously improved flame retardancy, smoke‐suppression, and thermal and viscoelastic properties. The cone‐calorimetry test results reveal that the peak heat‐release rate and total heat release of the composite (2 wt% FGO) are reduced by 39.7% and 29.9%, respectively, compared to those of the neat PP. Meanwhile, the total smoke released and total smoke production of PP are significantly (42.7% and 34.9%, respectively) reduced after composite formation with 2 wt% FGO. Similarly, the PP/FGO composite shows an improved maximum weight loss temperature of 392.4 °C, compared to that of neat PP (361.4 °C). Thermogravimetric Fourier‐transform infrared spectroscopy (TG‐FTIR) analysis further confirms that the composite reduces the evolution of the flammable components and toxic gases, especially CO gas, indicating that the FGO significantly decreases the fire hazards of the PP. The thermomechanical and melt‐rheological analyses reveal that the composite has higher mechanical stiffness and viscoelastic properties than the neat polymer. In summary, FGO is shown to have potential as an advanced additive to obtain PP composites with multifunctional properties; however, higher FGO loading would be needed to improve UL‐94 rating from V‐2 to V‐0.     

Development of LTCC micro-hotplate with PTC temperature sensor for gas-sensing applications

Low temperature co-fired ceramic (LTCC) micro-hotplates show wide applications in gas sensors and micro-fluidic devices. It is easily structured in three-dimensional structures. This paper presents the low power consumption micro-hotplates which were developed with PTC (positive temperature coefficient) temperature sensor and inter-digitated electrodes. The paper presents two different structures for micro-hotplate with platinum as a heating element. The PTC temperature sensor using two different materials viz. PdAg and platinum paste are developed with micro-hotplates. The simulation has been achieved through COMSOL for LTCC and alumina micro-hotplates. The temperature variation with power consumption has been measured for the developed LTCC micro-hotplates. The change in resistance of PTC temperature sensors was measured with micro-hotplate temperature. The aim of this study was to place a temperature sensor with the gas sensor module to measure and control the temperature of micro-hotplate. A SnO₂ sensing layer is coated on LTCC micro-hotplate using screen printing and characterized for the sensing of carbon monoxide gas (CO). This study will be beneficial for designing hotplates based on LTCC technology with low power consumption and better stability of temperature for gas-sensing applications.     

Development of advanced fiber-reinforced polymer composites by polymer hybridization technique: Emphasis on cure kinetics,mechanical, and thermomechanical performance

Polymer hybridization technique, consisting of an interlayer arrangement of different polymers, acts as the most economical and promising technique in augmenting the glass fiber-reinforced polymer composite's mechanical properties. This investigation focuses on the effect of cure kinetics on the flexural behavior of glass-polymer hybrid (GPH) composite, and also elucidates the comparative analysis on the mechanical behavior of glass-epoxy (GE) composite, glass-vinyl ester (GVE) composite, and GPH composite. The optimal postcuring temperature has been found to be 200°C for GPH composite among the other postcuring temperatures conducted at 140, 170, and 230°C. Among all these abovementioned composites, highest flexural strength and interlaminar shear strength properties have been recorded by the 200°C postcured GPH composite leading to 10.87 and 18.76% increment, respectively, compared with GE composite. Furthermore, thermomechanical characterization has been done to know the viscoelastic behavior of the GPH composite postcured at different temperatures using dynamic mechanical thermal analysis. The fracture morphology of flexural tested composite samples demonstrated a combination of failure modes. Relevant information on the chemical restructuring and fracture morphology of experimented composite material using Fourier-transform infrared (FTIR) spectroscopy and Scanning electron microscopy (SEM) has also been studied.     

Kinetic study of olefin polymerization with a supported metallocene catalyst. IV. Comparison of bridged and unbridged catalyst in gas phase

A kinetic study of ethylene/1‐hexene (E/1‐H) copolymerization is conducted with a supported bridged metallocene catalyst in a gas phase reactor. The investigation into the kinetics of ethylene/1‐hexene copolymerization includes the effects of operational parameters such as the reaction temperature, pressure, and comonomer concentration. On‐line perturbation techniques are implemented to determine key kinetic parameters such as the activation energies for propagation and catalyst deactivation. A comparison of the kinetic parameters and behavior is made between the bridged and a previously studied unbridged catalyst. Finally, a two‐site model is proposed to explain the observed kinetic behavior with changing reaction temperature and comonomer concentration. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1451–1459, 2001     

Modeling of the sheet‐molding process for poly(methyl methacrylate)

The sheet‐molding process for the production of poly(methyl methacrylate) (PMMA) involves an isothermal batch reactor followed by polymerization in a mold (the latter is referred to as a “sheet reactor”). The temperature at the outer walls of the mold varies with time. In addition, due to finite rates of heat transfer in the viscous reaction mass, spatial temperature gradients are present inside the mold. Further, the volume of the reaction mass also decreases with polymerization. These several physicochemical phenomena are incorporated into the model developed for this process. It was found that the monomer conversion attains high values of near‐unity in most of the inner region in the mold. This is because of the high temperatures there, since the heat generated due to the exothermicity of the polymerization cannot be removed fast enough. However, the temperature of the mold walls has to be increased in the later stages of polymerization so that the material near the outer edges can also attain high conversions of about 98%. This would give PMMA sheets having excellent mechanical strength. The effects of important operating (decision) variables were studied and it was observed that the heat‐transfer resistance in the mold influences the spatial distribution of the temperature, which, in turn, influences the various properties (e.g., monomer conversion, number‐average molecular weight, and polydispersity index) of the product significantly. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1951–1971, 2001     

Characterization of alkali‐treated jute fibers for physical and mechanical properties

Changes occurring in jute fibers when treated with a 5% concentration of a NaOH solution for 0, 2, 4, 6, and 8 h were characterized by weight loss, linear density, tenacity, modulus, FTIR, and X‐ray measurements. A 9.63% weight loss was measured during 2 h of treatment with a drop of hemicellulose content from 22 to 12.90%. The linear density value showed no change until 2 h of treatment followed by a decrease from 33.0 to 14.5 denier by 56% after 6 h of treatment. The tenacity and modulus of the fibers improved by 45 and 79%, respectively, and the percent breaking strain was reduced by 23% after 8 h of treatment. X‐ray diffractograms showed increase in crystallinity of the fibers only after 6 h of treatment, while FTIR measurements showed much of the changes occurring by 2 h of treatment with an increased amount of OH groups. By measuring the rate of change of the modulus, tenacity, and percent breaking strain with the time of treatment, a clear transition was apparent at 4 h of treatment with the dissolution of hemicellulose, causing a weight loss and drop in the linear density before and development of crystallinity with an improvement in the properties after the transition time. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1013–1020, 2001