Incremental transmission loss allocation under pool dispatch

Incremental transmission loss analysis has been used for decades, but recent interest in its application to loss allocation calls for new in-depth results. This paper demonstrates that, for incremental methods to be applied correctly in loss allocation, it is first necessary to specify the load distribution and loss supply strategies. Incremental loss allocation among bus power injections is shown to be arbitrary and, therefore, open to challenge as discriminatory. Loss allocation is possible among incremental loads and/or generators, but the proportion of the total losses assigned to either one is arbitrary. Unique, nonarbitrary incremental loss allocations are however possible among the "equivalent" incremental bilateral exchanges between generators and loads. From these basic components it is possible then to calculate the allocation among generators or loads in any specified proportion. The main results, although developed initially for small increments, are extended to large variations. Finally, a general incremental loss allocation algorithm is developed and tested     

Tritium Labeling of Androst-4-ene-3,17-dione by Liquid-Phase Selective Hydrogenation and Factors Affecting the Process

Androstenedione labeled with tritium at positions 1 and 2 was prepared. The molar radioactivity of the sample prepared using homogeneous catalysts was as high as 1.4-1.5 PBq mol^{- 1}. [1,2-³H]Androst-4-ene-3,17-dione can be converted into the [1-³H]steroid with the molar radioactivity of 0.9 PBq mol^{- 1}.     

Equal-channel angular extrusion of beryllium

The equal-channel angular extrusion (ECAE) technique has been applied to a powder metallurgy (P/M) source Be alloy. Extrusions have been successfully completed on Ni-canned billets of Be at approximately 425°C. No cracking was observed in the billets, and significant grain refinement was achieved. In this article, microstructural features and dislocation structures are discussed for a singlepass extrusion, including evidence of <c> and <c+a> dislocations. Significant crystallographic texture developed during ECAE, which is discussed in terms of this unique deformation processing technique and the underlying physical processes which sustain the deformation. S.R. AGNEW, formerly with the Oak Ridge National Laboratory, Oak Ridge, TN 37831-6115 This article is based on a presentation made in the symposium entitled “Defect Properties and Mechanical Behavior of HCP Metals and Alloys” at the TMS Annual Meeting, February 11–15, 2001, in New Orleans, Louisiana, under the auspices of the following ASM committees: Materials Science Critical Technology Sector, Structural Materials Division, Electronic, Magnetic & Photonic Materials Division, Chemistry & Physics of Materials Committee, Joint Nuclear Materials Committee, and Titanium Committee.     

Determination of dislocation densities in HCP metals from X-ray diffraction line-broadening analysis

X-Ray diffraction (XRD) line-broadening analysis has been performed on highly textured Zr-2.5Nb specimens which had been deformed in tensile tests to produce well-controlled dislocation structures. An iterative deconvolution method has been applied to extract the broadening function for the material, using as standards, a Zr single crystal and a 0 pct deformed specimen. In both cases, for specific tensile tests, a significant contribution to the basal line braodening was observed, which was clearly not directly related to the dislocation structure generated by the deformation, i.e., so-called c-component dislocations having a component of their Burgers vectors perpendicular to the basal plane. Calculations showed that the extent of basal line broadening cannot be attributed to the secondary effect of strain from a-type dislocations, i.e., dislocations with Burgers vectors parallel with the basal plane. It is concluded that most of the line broadening observed was the result of intergranular strain distributions. These distributions are most prominent for grains oriented with their c-axes perpendicular to the tensile-deformation axis and resulted in basal-plane line broadening even when there were few, if any, c-component dislocations present. This article is based on a presentation made in the symposium entitled “Defect Properties and Mechanical Behavior of HCP Metals and Alloys” at the TMS Annual Meeting, February 11–15, 2001, in New Orleans, Louisiana, under the auspices of the following ASM committees: Materials Science and Critical Technology Sector, Structural Materials Division, Electronic, Magnetic & Photonic Materials Division, Chemistry & Physics of Materials Committee, Joint Nuclear Materials Committee, and Titanium Committee.     

Crisis phenomena upon evaporation in grid capillary and porous coatings and arterial structures of heat pipes

The article presents the results of experimental investigations of critical (limit) heat fluxes upon evaporation on porous coatings, and it substantiates the physical model of the process.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 49, No. 4, pp. 607–614, October, 1985.     

Vapor pressure and thermodynamic functions of TeI<Subscript>4</Subscript> and its decomposition products

Using a flow method, we have measured the vapor pressure of tellurium tetraiodide, an attractive reagent for chemical vapor deposition technology. The results, combined with earlier tensimetric data, have been used to evaluate the basic thermodynamic functions of TeI₄ and its thermolysis products.     

FATIGUE DAMAGE IN 1045 STEEL UNDER VARIABLE AMPLITUDE BIAXIAL LOADING

Abstract— During constant amplitude loading, two different types of crack systems have been reported In the high cycle fatigue (HCF) region, cracks nucleate on a small number of maxium shear strain amplitude planes One of these cracks becomes a dominant crack and leads to failure of the specimen In the low cycle fatigue (LCF) region, equally developed microcracks are observed over the entire gage section and grow during the majority of the life. The failure is due to a linking in which the microcracks join up during the last few cycles of the fatigue life.
To investigate the interaction of these two types of crack systems in biaxial fatigue, experiments were performed on thin-wall tubular specimens in tension, torsion and combined tension-torsion loading The test program included step loading and block loading in which two equivalent strain amplitudes were employed. One of the equivalent strain amplitudes is in the HCF region and the other was in the LCF region
Fatigue lives were predicted from constant amplitude damage curves when a single crack system dominated the fatigue process Two competitive crack systems were sometimes developed on the maximum shear strain amplitude planes in a single specimen under block loading This resulted in a conservative prediction of the fatigue life.     

AN ASSESSMENT OF CRACK CLOSURE AND THE EXTENT OF THE SHORT CRACK REGIME IN Q1N (HY80) STEEL

Abstract— The paper addresses some aspects of the differences in fatigue crack growth rate behaviour and threshold values obtained for long through-cracks, short through-cracks and surface cracks. Attention is focused on plasticity induced closure in the wake behind the growing crack tip. For long cracks at high K _max, closure is found to depend in a linear manner on K _max, i.e. K _op, increases with the size of the monotonic plastic zone. Closure increases at low δ K and this is primarily a consequence of the load shedding procedure. If short through-cracks are prepared by machining specimens containing long cracks, a substantial part of the plastic wake is removed and this can produce marked effects on the closure contribution during subsequent growth. The length of crack "closed" in a long crack threshold test was found to be of the order of 1 mm. Cracks less than this length exhibited "short crack" behaviour: greater than this length, they behaved as "long cracks", with plastic wake effects apparently fully operative. Small surface cracks exhibit "long crack" behaviour at lengths as short as 0.2 mm and reasons for this are discussed.