基于MPEG-2文件的合并

介绍了具有相同音频、视频编码方式的MPEG - 2节目流如何合并成一个节目流。合并后的文件播放流畅并且时间显示正确 ,它包括PATPMT表的重写 ,系统头部分相关字段的更改 ,PCR值的修改 ,解码时间标签 (DTS)和显示时间标签 (PTS)的重新确定 ,传送速率的修改以及添加相应的空包     

Numerical Study of Finite Element Method Based Solutions for Propagation of Wetting Fronts in Unsaturated Soil

The accurate prediction of the propagation of a wetting front in an unsaturated soil subjected to surficial infiltration is of practical importance to many geotechnical and geoenvironmental problems. The finite element method is the most common solution technique as the hydraulic soil properties are highly nonlinear. Two important issues are often found to create difficulties in such analyses. First, numerical oscillations are usually observed in the calculated pore pressures at the wetting front. Second, when a reasonable mesh size and time step are used, the elevation of the wetting front may be seriously overpredicted. This paper is focused on the second issue. The under-relaxation (UR) technique used in the iterative process within each time step is found to have a serious impact on rate of convergence with refinement in mesh size and time step. Two different techniques are typically used; the first evaluates the hydraulic conductivity using an average of heads calculated from the preceding time node and the most recent iteration of the current time node (UR1), and the second evaluates the hydraulic conductivity using the average of heads calculated from the two most recent iterations of the current time nodes (UR2). The study shows that UR1, which is adopted in programs such as SEEP/W, ensures that the solution converges rapidly to a stable solution within a time step, but may converge to the wrong wetting front at a given elapsed time unless a sufficiently refined mesh is used. UR2 converges much more slowly within a time step, but the error in the wetting front is smaller than that generated by UR1.     

ㄇ形梁剪力滞效应的解析解

精确分析ㄇ形梁在纵横向荷载共同作用下,其横断面上正应力分布规律对于计算其有效宽度有重要意义,应用力法原理,先将ㄇ形梁和翼板截开成矩形截面梁和平面应力板,在截面上代之以赘余的分布剪力,对于平面应力板,通过利用板变形的对称性来简化其边界条件,然后假设一个满足板的控制方程的Airy应力函数求得板的应力和位移,再利用Timoshenko梁理论求得梁的挠度和转角,根据截面上梁与板的纵向位移相等的变形协调条件便可最终确定截面上的分布剪力,给出的数值算例验证了方法的有效性,并与铜陵长江公路大桥主梁的模型有限元结果和试验结果作了对比,解析解法还可用来检验其他各种数值计算方法的精度,并可推广到其他多跨薄壁结构梁桥的膜应力分析中。     

电子电路中抗EMI设计

电磁干扰(EMI)可分为传导干扰和辐射干扰,消除干扰的方法可以采用硬件方法和软件方法,硬件方法主要有屏蔽、接地、隔离和滤波等,而软件方法主要是滤波。笔者对各种方法进行总结,并指出各种方法所存在的问题以及适用场合,并对一些常用方法提出改进措施。     

基于信息的智能控制理论研究

本文介绍的基于信息的智能控制理论的发展过程，主要分为智能控制的信息指标和智能控制的信息结构分析两部分，文中在最后对这套理论可能的发展方向进行了探讨。     

Delay-dependent state estimation for delayed neural networks

In this letter, the delay-dependent state estimation problem for neural networks with time-varying delay is investigated. A delay-dependent criterion is established to estimate the neuron states through available output measurements such that the dynamics of the estimation error is globally exponentially stable. The proposed method is based on the free-weighting matrix approach and is applicable to the case that the derivative of a time-varying delay takes any value. An algorithm is presented to compute the state estimator. Finally, a numerical example is given to demonstrate the effectiveness of this approach and the improvement over existing ones.     

锑酸消除含氚废空气中的氚

用锑酸作消气材料 ,压制成消氚电极 ,在适当外加条件下 ,考察了锑酸作消氚材料直接将含氚废空气中的氚除去的可能性。对消氚过程中料气中氚的浓度及水分对消氚结果的影响进行了考察 ,给出了消气片中氚的物料平衡。结果表明 :在 3 2L含氚空气中 ,用锑酸制成的消氚材料 ,在 2 0 0min左右可将原料气氛中 80 %以上的氚去除     

喷射轧制Fe-4.5%Si硅钢片的组织和性能

采用喷射成形和轧制工艺制备了厚度为0.5mm的Fe-4.5%Si高硅钢片，并对其密度、显微组织和电磁性能进行了测试分析，研究结果表明：在最佳的喷射成形和轧制工艺条件下，所制备硅钢片的磁感应强度B25为1.544T、B50为1.641T；铁损P1050为1.437W/kg、P1550为3.43W/kg，说明喷射成形轧制技术可以制备出高磁感应强度、低铁损的高硅钢片。     

汽车稳定杆组织与疲劳性能研究

对28Mn6钢制造的汽车稳定杆，分别采用整体感应加热－整体淬火、连续感应加热淬火两种不同热处理工艺，并进行了台架疲劳寿命试验，采用光学显微镜和扫描电镜，分析了经两种不同热处理工艺处理的稳定杆的金相组织及其早期疲劳断裂的断口形貌，提出，获得细小的高韧性索氏体组织是保证良好疲劳寿命的关键，稳定杆喷丸表面质量，游离铁素体也是影响疲劳性能的重要因素。     

KZON-50/120空分设备的安装调试及设计改造

在KZON-50/120空分设备的安装调试和试运行过程中,对其机械和电器部分进行了多处改造,克服了原设计中存在的不足之处。改造后,机械和电器性能更加趋于合理,操作简单,便于维护,降低了制气费用,提高了制气纯度和经济效益,保证了空分设备更加安全可靠运行。