圆柱体相贯线上的圆角表示方法

在机械设计中，圆柱体相贯线上的圆角表示方法是CAD和计算机辅助设计中的难题，所有的CAD／CAM软件都没有这一功能，多数使用者采用的是各种近似方法。本文介绍了严密精确的设计和几何造型方法，可用于大型铸锻件和重型机械的CAD和计算机辅助设计。     

高层住宅结构设计

主要介绍长沙梦泽园高层住宅从基础到上部楼层各部位的结构设计,以及在设计、施工过程中所考虑的一些问题及处理方法。     

Effect of surface free energy on the adhesion of biofouling and crystalline fouling

Pipelines and heat exchangers using seawater as coolant suffer from biofouling. Biofouling not only reduces heat transfer performance significantly, but also causes considerable pressure drop, calling for higher pumping requirements. It would be much more desirable if surfaces with an inherently lower stickability for biofouling could be developed. In this paper, a cost-effective autocatalytic graded Ni-Cu-P-PTFE composite coating with corrosion-resistant properties was applied to reduce biofouling formation. The experimental results showed that the surface free energy of the Ni-Cu-P-PTFE coatings, which were altered by changing the PTFE content in the coatings, had a significant influence on the adhesion of microbial and mineral deposits. The Ni-Cu-P-PTFE coatings with defined surface free energy reduced the adhesion of these deposits significantly. The anti-bacterial mechanism of the composite coatings was explained with the extended DLVO theory.     

Analysis of the oscillatory behavior of double-walled carbon nanotube-based oscillators

Molecular dynamics simulations of oscillatory behaviors of double-walled carbon nanotube-based oscillators are performed. The second-generation empirical bond-order potential is used for the atomic interactions within a wall, and a registry-dependent and four different registry-independent van der Waals potentials are used for the atomic interactions between walls. It is found that the frequencies of the nanotube oscillators are sensitive to the choice of the van der Waals potentials. An almost non-decay oscillation is observed for the registry-dependent potential when there is no rocking motion. However, an apparent decay oscillation is observed when rocking motion occurs. A decay oscillation is observed for all registry-independent potentials even without rocking motion. Mechanisms leading to unstable oscillatory behavior are analyzed.     

Abrasion erosion of concrete by water-borne sand

Hydraulic concrete structures frequently experience long-term abrasive erosion by water-borne sand, resulting in surface damage and eventually limiting their service life. In this study, the investigation of abrasion erosion tests on concrete with various water to cementitious material ratios (w/cm) was performed. The effects of the constituent materials on concrete structure abrasion erosion resistance were studied. The test results show that: (1) reduction in the w/cm ratio increases the tested concrete abrasion resistance; (2) the splitting tensile strength is a viable indicator for concrete abrasion resistance; (3) high permeability concrete exhibits weak abrasion resistance; and (4) concrete and low strength concrete made with coarser aggregate exhibit greater abrasion resistance.     

Simultaneous recovery of copper and surfactant by an electrolytic process from synthetic solution prepared to simulate a concentrate waste stream of a micellar-enhanced ultrafiltration process

Electroplating method was employed to recover copper and surfactant simultaneously from synthetic solutions prepared to simulate concentrated waste stream generated from micellar-enhanced ultrafiltration. Effects of surfactant and copper (II) concentrations, surfactant to copper (II) molar ratio (S/M), electroplating voltage and time, solution pH, and ionic strength on metal recovery and electrical current efficiency were investigated. Results show that at a fixed S/M ratio of 5, the first-order kinetic constant for Cu (II) removal by electroplating increases with decreasing SDS concentration. At fixed SDS concentration of 8.5 mM, increasing initial Cu (II) concentration increases both Cu (II) recovery and current efficiency. Electrolyte pH has profound effects on the metal recovery and current efficiency due to the difference in solution conductivity after pH adjustment and the extent of Cu (II) adsorption onto SDS at different pHs.     

Effect of preparation conditions on the properties of a coal-derived activated carbon honeycomb monolith

Activated carbon honeycomb (ACH) monoliths were prepared by extruding of a mixture of bituminous coal and organic additives and subsequent carbonization and steam activation. Preparation parameters that were varied were carbonization temperature and activation time. The carbonization conditions were 500, 650 and 800 °C for 1 h and the steam activation conditions were 850 °C for 2, 4 and 6 h. The monoliths at various states were characterized by SEM, XRD, nitrogen adsorption and compression test. It was found that carbonization temperature has significant effects on pore size distribution and mechanical strength of ACH monoliths. The ACH monoliths prepared from high carbonization temperatures exhibited lower values of the BET surface area and total pore volume and higher value of the mechanical strength than those of the ACH monoliths prepared from low carbonization temperatures. This was attributed to the effect of high temperature carbonization that results in the formation of relatively less defective structures.     

A rheological model for iron oxide suspensions

We have examined the rheological properties of a Co-adsorbed γ-Fe₂O₃ magnetic suspension with polyurethane (PU) as a binder and methyl ethyl ketone (MEK) or cyclohexanone (CH) as a solvent. A Haake RV20 viscometer was used to measure the suspension viscosity and the vane method was adopted to determine the fluid yield stress. A rheological model which can be viewed as a combination of the Casson model and the Bingham model is proposed to describe the suspension viscosity. The effects of temperature, particle content, and binder concentration are included in the model.     

新型液晶PVDF合金的研究

本文系统地研究了液晶聚合物(LCP)与PVDF合金共混体系的组成及加工工艺条件对共混物制件性能的影响。并用SEM观察了合金的形态结构。结果表明:在液晶含量10%左右时,加工温度为210℃,合金的拉伸强度最高,磨耗量最低,体系分散均匀并形成了较多的微纤结构。