Application of nanostructured titanium dioxide pigments in paper coating: a comparison between prepared and commercially available ones

Nano-TiO₂ pigments in pure crystallographic anatase and rutile phases have been successfully prepared by hydrothermal at 120°C and hydrolysis methods, respectively. The laboratory-prepared pigments were characterized parallel to two commercial pigments of the same crystal structure. All pigments were applied in paper coating mixtures, and their influence on coated paper properties was systematically investigated. X-ray diffraction investigation showed that the laboratory-prepared pigments using the hydrothermal method at 120°C were pure anatase, whereas hydrolysis method produced pure rutile phase pigment. The application of the prepared nanopigments and the corresponding commercial TiO₂ phases in paper coating revealed that clay/rutile nano-TiO₂ pigments in paper coating mixture decreased coated paper roughness more than blending clay with anatase nano-TiO₂ pigments. Commercial nano-TiO₂ pigments increased porosity of coated paper at both the 30% and 50% addition of nano-TiO₂ pigments to clay, while laboratory-prepared nano-TiO₂ pigments highly decreased it at 30% addition of nano-TiO₂ to clay, compared to clay only. Blending of clay/nano-TiO₂ pigments improved both brightness and opacity of the coated paper where commercial pigments are more effective. Burst, tensile strength, stretching, and TEA were improved in the case of all pigments. The 50% addition of the prepared and commercial nanopigments in conjunction with clay improved the mechanical coated paper properties more than 30% addition (except the cases of stretching and TEA of the commercial pigments). The coated paper samples were offset printed. It was found that blending of clay/nano-TiO₂ pigments improved print density. Commercial nano-TiO₂ pigments improved print gloss more than the laboratory-prepared ones. This result was found consistent with the results of coated paper roughness.     

Effect of the compatibilizer,on the engineering properties of TPV based on Hypalon® and PP prepared by dynamic vulcanization

Elastomeric Chlorosulfonated polyethylene (Hypalon^®) and thermoplastic Polypropylene (PP) based thermoplastic vulcanizates (TPVs) were prepared in presence of different doses of compatibilizer, maleic anhydride grafted PP (PP‐g‐MA) by employing dynamic vulcanization technique. The effect of incorporation in different proportions of compatibilizer on mechanical, spectral, morphological, thermal, and rheological properties of such TPVs was studied and the same were compared to that of virgin PP and amongst themselves. The mechanical analysis of the prepared TPVs exhibited significant improvements in stress at 25% modulus, ultimate tensile strength (UTS), and hardness values. FTIR studies revealed that a chemical interaction had taken place between Hypalon^® and functionalized compatibilizer during the process of dynamic vulcanization which led to an enhancement of interfacial adhesion between them. The two‐phase morphologies were clearly observed by scanning electron microscopic studies. The T_g values of Hypalon^® was modified in the TPVs as exhibited by differential scanning calorimetric studies. TGA studies indicated the increase in thermal stability of all TPVs with respect to the elastomeric Hypalon^®. Rheological properties showed that the compatibilizer reduces the melt viscosity of TPVs and thus facilitates the processibility of such TPVs. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40312.     

Potential Pro-Inflammatory Effect of Vitamin E Analogs through Mitigation of Tetrahydrocannabinol (THC) Binding to the Cannabinoid 2 Receptor

Vitamin E acetate, which is used as a diluent of tetrahydrocannabinol (THC), has been reported as the primary causative agent of e-cigarette, or vaping, product use-associated lung injury (EVALI). Here, we employ in vitro assays, docking, and molecular dynamics (MD) computer simulations to investigate the interaction of vitamin E with the membrane-bound cannabinoid 2 receptor (CB2R), and its role in modulating the binding affinity of THC to CB2R. From the MD simulations, we determined that vitamin E interacts with both CB2R and membrane phospholipids. Notably, the synchronized effect of these interactions likely facilitates vitamin E acting as a lipid modulator for the cannabinoid system. Furthermore, MD simulation and trajectory analysis show that when THC binds to CB2R in the presence of vitamin E, the binding cavity widens, facilitating the entry of water molecules into it, leading to a reduced interaction of THC with CB2R. Additionally, the interaction between THC and vitamin E in solution is stabilized by several H bonds, which can directly limit the interaction of free THCs with CB2R. Overall, both the MD simulations and the in vitro dissociation assay results indicate that THC binding to CB2R is reduced in the presence of vitamin E. Our study discusses the role of vitamin E in limiting the effect of THCs and its implications on the reported pathology of EVALI.     

CFD simulations of the Andersen cascade impactor: Model development and effects of aerosol charge

Cascade impactors are commonly used to assess the size characteristics of aerosols in toxicology and pharmaceutical applications. These aerosol instruments have been developed and refined over decades. However, a number of questions remain related to impactor performance, including the influence of electrostatic charge on measured size distributions. The objective of this study was to develop a validated CFD model of the Mark II Andersen cascade impactor (ACI) and apply this model to evaluate the effects of particle charge on deposition. The flow field was simulated using a commercial CFD code for incompressible laminar and transitional flows. Particle trajectories and deposition were evaluated using a well tested Lagrangian tracking approach that accounts for impaction, sedimentation, diffusion, and electrostatic attraction. Particle charge levels typical of dry powder inhaler (DPI) and metered dose inhaler (MDI) aerosols were considered for a particle size range of 0.3–12 μm. As a model validation, computational predictions of cutoff d₅₀ diameters for each of the eight ACI stages were found to be within 10% difference of existing experimental and manufacturer data. Results indicated that charges consistent with DPI and MDI aerosols increased deposition fraction in Stages 0–3 by up to 30% and increased deposition fraction in Stages 4–7 by up to an order of magnitude. For Stages 0–3, both DPI and MDI charges reduced the d₅₀ value by approximately 10% or less. In contrast, charged aerosols reduced the d₅₀ values in Stages 4 and 5 by 200% and 60%, respectively. All charged submicrometer aerosols considered deposited in Stages 6 and 7. Increasing the particle charge by an order of magnitude from DPI to MDI values had a relatively small effect on further decreasing the cutoff size of each stage. In conclusion, these results can be used to approximate the actual aerodynamic diameter of a charged pharmaceutical aerosol based on measurements in a standard ACI. Future applications of the developed ACI model include evaluating the influence of space charge on deposition and quantifying the effects of aerosol condensation and evaporation on size assessment.     

Two-Variable Refined Plate Theory for Thermoelastic Bending Analysis of Functionally Graded Sandwich Plates

The thermoelastic bending analysis of functionally graded sandwich plates using the two-variable refined plate theory is presented in this paper. Unlike any other theory, the number of unknown functions involved is only four, as against five in case of other shear deformation theories. The theory presented is variationally consistent, has strong similarity with classical plate theory in many aspects, does not require shear correction factor, and gives rise to transverse shear stress variation such that the transverse shear stresses vary parabolically across the thickness satisfying shear stress free surface conditions. The sandwich plate faces are assumed to have isotropic, two-constituent material distribution through the thickness, and the modulus of elasticity, Poisson's ratio of the faces, and thermal expansion coefficients are assumed to vary according to a power law distribution in terms of the volume fractions of the constituents. The core layer is still homogeneous and made of an isotropic ceramic material. Several kinds of sandwich plates are used taking into account the symmetry of the plate and the thickness of each layer. The influences played by the transverse shear deformation, thermal load, plate aspect ratio, and volume fraction distribution are studied. Numerical results for deflections and stresses of functionally graded metal–ceramic plates are investigated. It can be concluded that the proposed theory is accurate and simple in solving the thermoelastic bending behavior of functionally graded plates.     

Prodynorphin and Proenkephalin in Cerebrospinal Fluid of Sporadic Creutzfeldt–Jakob Disease

Proenkephalin (PENK) and prodynorphin (PDYN) are endogenous opioid peptides mainly produced in the striatum and, to a lesser extent, in the cerebral cortex. Dysregulated metabolism and altered cerebrospinal fluid (CSF) levels of PENK and PDYN have been described in several neurodegenerative diseases. However, no study to date investigated these peptides in the CSF of sporadic Creutzfeldt–Jakob disease (sCJD). Using liquid chromatography-multiple reaction monitoring mass spectrometry, we evaluated the CSF PDYN- and PENK-derived peptide levels in 25 controls and 63 patients with sCJD belonging to the most prevalent molecular subtypes (MM(V)1, VV2 and MV2K). One of the PENK-derived peptides was significantly decreased in each sCJD subtype compared to the controls without a difference among subtypes. Conversely, PDYN-derived peptides were selectively decreased in the CSF of sCJD MV2K, a subtype with a more widespread overall pathology compared to the sCJD MM(V)1 and the VV2 subtypes, which we confirmed by semiquantitative analysis of cortical and striatal neuronal loss and astrocytosis. In sCJD CSF PENK and PDYN were associated with CSF biomarkers of neurodegeneration but not with clinical variables and showed a poor diagnostic performance. CSF PDYN and PENK-derived peptides had no significant diagnostic and prognostic values in sCJD; however, the distinct marker levels between molecular subtypes might help to better understand the basis of phenotypic heterogeneity determined by divergent neuronal targeting.     

Discontinuous Precipitation and Phase Stability In Re- and Ru-Containing Nickel-Base Superalloys

The phase stability of nickel-base superalloys has been investigated using a new in-house-designed alloy series with stepwise increased additions of Re and Ru at otherwise fixed atomic fractions of alloying elements. Results presented in this study are focused on the lesser-known topologically closed packed (TCP) formation of columnar colonies or so-called discontinuous precipitation. A detailed investigation of these colonies allowed for identifying compositional changes during the growth process and for providing a three-dimensional (3-D) illustration of the TCP phases within these colonies. The results were used to compare the colony growth process with existing growth models. Furthermore, the influence of Re and Ru on the appearance of discontinuous precipitation has been investigated by means of colony width and the effect on creep properties. Larson-Miller plots are given to illustrate the creep strength of directionally solidified samples with and without TCP colonies compared with single crystalline samples free from TCP colonies.