Effect of microwave pretreatment of mixed culture on biohydrogen production from waste of sweet produced from Benincasa hispida

To enhance the production of biohydrogen from biomass, various pretreatment methods play important role. In this study, effect of microwave irradiation on the culture was studied on biohydrogen production from Benincasa hispida (Petha) solid waste at different powers for a fixed interval of time. The highest power studied was 800 W with a frequency of 2450 MHz. The amount of soluble sugars found in the waste was 13.9 mg/L having the chemical oxygen demand (COD) of 3000 mg/L. Studies have been performed in batch reactors using mixed consortia and results were also compared with the reactor operated at the normal conditions i.e. without any inoculum pretreatment. Maximum hydrogen produced was 14 mmol H₂ per mol of soluble sugar consumed in the reactor in which the inoculum was exposed to 320 W of microwave for 5 min. SEM analysis of this microwave pretreated culture was done.     

Study on GDC-KZnAl composite electrolytes for low-temperature solid oxide fuel cells

Development of low-temperature solid oxide fuel cells (LTSOFC) is now becoming a mainstream research direction worldwide. The advancement in the effective electrolyte materials has been one of the major challenges for LTSOFC development. To further improve the performance of electrolyte, composite approaches are considered as common strategies. The enhancement on ionic conductivity or sintering behavior ceria-based electrolyte can either be done by adding a carbonate phase to facilitate the utilization of the ionic-conducting interfaces, or by addition of alumina as insulator to reduce the electronic conduction of ceria. Thus the present report aims to design a composite electrolyte materials by combining the above two composite approaches, in order to enhance the ionic conductivity and to improve the long-term stability simultaneously. Here we report the preparation and investigation of GDC-KAlZn materials with composition of Gd doped ceria, K₂CO₃, ZnO and Al₂O₃. The structure and morphology of the samples were characterized by XRD, SEM, etc. The ionic conductivity of GDC-KAlZn sample was determined by impedance spectroscopy. The composite samples with various weight ratio of GDC and KAlZn were used as electrolyte material to fabricate and evaluate fuel cells as well as investigate the composition dependent properties. The good ionic conductivity and notable fuel cell performance of 480 mW cm⁻² at 550 °C has demonstrated that GDC-KAlZn composite electrolyte can be regarded as a potential electrolyte material for LTSOFCs.     

Visible‐light‐induced controlled/living radical polymerization of styrene with a phenyl seleno group at one terminal chain end: 1‐(Phenylseleno)ethyl benzene as a photoiniferter

The photopolymerization of styrene with a well‐defined molecular architecture and a low polydispersity index and with methyl and phenylseleno (? SePh) groups at α‐ and ω‐chain ends, respectively, was performed via a controlled/living radical polymerization with a new initiating system, 1‐(phenylseleno)ethyl benzene/tert‐butyl diphenyl (phenylseleno) silane, through the absorption of visible light at room temperature. A novel initiating living radical polymerization was examined. The yield and number‐average molecular weight (M_n) of the resulting polymer increased with the reaction time. Furthermore, a linear relationship was found in a plot of M_n versus the polymer yield. These results indicated that this polymerization proceeded through a living radical mechanism. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 348–355, 2004     

Identification of pole-like structures from mobile lidar data of complex road environment

Pole-like structures (PLSs) located in road environment are important roadway assets. They play a vital role in road safety inspection and road planning. The use of light detection and ranging (lidar) based mobile mapping technology for mapping of PLSs is an important area of research as it holds the potential for automation. Point cloud data of rural, peri-urban, and urban road environment are used in this study, which pose special challenge in view of the complexity of terrain, unlike well-planned roads, which have been the subject of interest in existing literature for identification of PLSs. A new five-step method is proposed in this article. The first two steps, i.e. ground filtering and voxelization of filtered non-ground points, are used for data size reduction. Next three steps are used to extract PLSs from reduced data. The proposed method was tested on point cloud data of three test sites having different levels of complexities. PLSs including partially occluded pole, tilted pole, pole situated very close to other objects, and vertical pole attached to tilted pole were accurately identified. Average correctness and completeness, respectively of 92.6% and 94.9%, were achieved in three different complex test sites, i.e. urban, peri-urban, and rural sites, respectively. Computation complexity shows that our proposed method delivers fast and computationally efficient solution for identifying the PLSs from volumetric mobile lidar point cloud. Impact of PLSs on road safety and road planning is also addressed for these selected test sites.     

Effect of EGR on the exhaust gas temperature and exhaust opacity in compression ignition engines

In diesel engines, NOx formation is a highly temperature-dependent phenomenon and takes place when the temperature in the combustion chamber exceeds 2000 K. Therefore, in order to reduce NOx emissions in the exhaust, it is necessary to keep peak combustion temperatures under control. One simple way of reducing the NOx emission of a diesel engine is by late injection of fuel into the combustion chamber. This technique is effective but increases fuel consumption by 10–15%, which necessitates the use of more effective NOx reduction techniques like exhaust gas recirculation (EGR). Re-circulating part of the exhaust gas helps in reducing NOx, but appreciable paniculate emissions are observed at high loads, hence there is a trade-off between NOx and smoke emission. To get maximum benefit from this trade-off, a paniculate trap may be used to reduce the amount of unburnt particulates in EGR, which in turn reduce the paniculate emission also. An experimental investigation was conducted to observe the effect of exhaust gas re-circulation on the exhaust gas temperatures and exhaust opacity. The experimental setup for the proposed experiments was developed on a two-cylinder, direct injection, air-cooled, compression ignition engine. A matrix of experiments was conducted for observing the effect of different quantities of EGR on exhaust gas temperatures and opacity     

A novel method for high-resolution imaging of coating distribution within a rough-textured plywood surface

A new method was developed which enabled us to obtain high-resolution images of the distribution of an oil-borne stain in a saw-textured plywood surface. The method involved treating 90 μm thick plywood sections, which had been cut transversely through the wood-coating interface using a sliding microtome, with osmium tetroxide (OsO₄) prior to examination with a field-emission scanning electron microscope (FE-SEM) operating in backscattered electron imaging (BEI) mode. The combination of OsO₄ staining and use of FE-SEM-BEI afforded excellent contrast differentiation between the coating and wood cell walls, revealing coating penetration into even nano-size cell wall cracks and delaminations formed during band-sawing of the plywood. The novel technique described adds a new dimension to probing wood–coating interface.     

Free Vibration Analysis of an Eccentric Thermoelastic Hollow Cylinder

The three-dimensional free vibrations in a simply supported homogeneous isotropic, thermally conducting, circular cylinder of finite length with an eccentrically located inner circular cavity have been studied. The surfaces of the cylinder are subjected to stress free and thermally insulated or isothermal boundary conditions. The three-dimensional linear theory of coupled thermoelasticity has been employed to model the problem. The displacement potential functions have been introduced to decouple purely shear and longitudinal motions. The purely transverse wave has been found to remain unaffected due to thermal field. The translation addition theorem for cylindrical wave functions along with orthogonal series expansions has been used to develop the exact solution. To illustrate the analytical results, the numerical solution of some relations and equations have been obtained to compute lowest frequency and dissipation factor versus eccentricities, for selected length to radius ratio and radius ratio of hollow cylinder. The computer simulated results have been carried out with the help of MATLAB software and are presented graphically.