Applications of microstructures fabricated by proton beam writing to electric-micro filters

Fabrication of high-aspect-ratio microstructures was performed by proton beam writing (PBW) using a microbeam line at Takasaki Ion Accelerators for Advanced Radiation Application (TIARA), JAEA Takasaki, JAPAN. As one of the applications of the high-aspect-ratio structures micro-machined by PBW, we utilized the high-aspect pillars for electric-micro filters of microbes such as Escherichia coli and Yeast based on the dielectrophoretic force. The filter is equipped with high-aspect pillars with a height of ～20 μm and a diameter of ～1 μm on a glass plate. Evaluation of the dielectrophoresis (DEP) device for capturing E. coli and Yeast was made using either observation by optical microscope or photoluminescence (PL) measurements.     

Detail analysis of fusion neutronics benchmark experiment for iron

In order to specify the best nuclear data on iron, the fusion neutronics benchmark experiment on iron at Japan Atomic Energy Agency (JAEA)/Fusion Neutronics Source (FNS) was analyzed in detail with MCNP-4C and the latest nuclear data libraries, JENDL-3.3, FENDL-2.1, JEFF-3.1 and ENDF/B-VII.0. As a result, totally the calculation result with ENDF/B-VII.0 agreed with the measurement best, except that it underestimated the measured neutron flux above 10 MeV with the depth. It was noted that the calculation result with JENDL-3.3 overestimated the measured neutrons below a few keV. Through the DORT calculations based on the iron data in ENDF/B-VII.0, it was found out that the first inelastic scattering cross-section data of ⁵⁷Fe in JENDL-3.3 caused the overestimation.     

Developmental ability of cloned embryos from neural stem cells

The success rate is generally higher when cloning mice from embryonic stem (ES) cell nuclei than from somatic cell nuclei, suggesting that the embryonic nature or the undifferentiated state of the donor cell increases cloning efficiency. We assessed the developmental ability of cloned embryos derived from cultured neural stem cell (NSC) nuclei and compared the success rate with that of embryos cloned from other donor cells such as differentiated NSCs, cumulus cells, Sertoli cells and ES cells in the mouse. The transfer of two-cell cloned embryos derived from cultured NSC nuclei into surrogate mothers produced five live cloned mice. However, the success rate (0.5%) was higher in embryos cloned from cultured NSC nuclei than from differentiated NSCs (0%), but lower than that obtained by cloning mice from other cell nuclei (2.2-3.5%). Although the in vitro developmental potential to the two-cell stage of the cloned embryos derived from NSC nuclei (73%) was similar to that of the cloned embryos derived from other somatic cell nuclei (e.g., 85% in Sertoli cells and 75% in cumulus cells), the developmental rate to the morula-blastocyst stage was only 7%. This rate is remarkably lower than that produced from other somatic cells (e.g., 50% in Sertoli cells and 54% in cumulus cells). These results indicate that the undifferentiated state of neural cells does not enhance the cloning efficiency in mice and that the arrest point for in vitro development of cloned embryos depends on the donor cell type.     

Synergistic Extraction of Am(III) and Eu(III) by Tris(2‐pyridylmethyl)Amine with Various Anions in 1,2‐Dichloroethane

The extraction equilibria of Am(III) and Eu(III) by using a tripodal ligand, tris(2‐pyridylmethyl)amine (tpa), with various lipophilic anions have been investigated. The extractability of both Am(III) and Eu(III) was increased by the combination of tpa and counteranions due to a synergistic effect. The separation factors between Am(III) and Eu(III) were also increased from 7.6 to 49 by the combination of counteranions and organic solvents. The extraction equilibria of Am(III) and Eu(III) with tpa in 1,2‐dichloroethane were determined by slope analysis. It was found that three anions and one molecule of the ligand coordinated to Am(III) and Eu(III) was extracted regardless of the anions.     

Determination of acrylamide in processed foods by LC/MS using column switching

An LC/MS method was developed for the determination of acrylamide (AA) in processed or cooked foods. AA was extracted with a mixture of water and acetone from homogenized food samples after the addition of 13C-labeled acrylamide (AA-1-(13)C) as an internal standard. The extract was concentrated, washed with dichloromethane for defatting, and cleaned up on Bond Elut C18, PSA and ACCUCAT cartridge-columns, and then AA was determined by LC/MS in the selected ion recording (SIR) mode. For the LC/MS analysis, four LC columns were connected in-line and the flow of the mobile phase was switched according to a time-program. Monitoring ions for AA were m/z 72 and 55, and those for AA-1-(13)C were m/z 73 and 56. AA and AA-1-(13)C were determined without interference from the matrices in all samples. The recoveries of AA from potato chips, corn snack, pretzel and roasted tea spiked at the level of 500 ng/g of AA were 99.5-101.0% with standard deviations (SD) in the range from 0.3 to 1.6%. The limits of detection and quantification of the developed method were 9 and 30 ng/g for AA in samples, respectively. The method was applied to the analysis of AA in various processed or cooked food samples purchased from retail markets. High levels of AA were found in potato chips and French-fried potato (467-3,544 ng/g). Fried and sugar-coated dough cakes (karinto) contained 374 and 1,895 ng/g. Corn snacks contained 117-535 ng/g of AA. Roasted foods (such as roasted sesame seed, roasted barley (mugi-cha), roasted tea (hoji-cha), coffee beans and curry powder) contained 116-567 ng/g of AA. Foods made from fish, egg and meat contained lower levels of AA than the plant-based foods. Foods containing much water showed a tendency to have low levels of AA compared with dry foods. The proposed method was applicable to the analysis of AA in variety of processed foods.     

Iron–Nitrogen‐Doped Vertically Aligned Carbon Nanotube Electrocatalyst for the Oxygen Reduction Reaction

A highly active iron–nitrogen‐doped carbon nanotube catalyst for the oxygen reduction reaction (ORR) is produced by employing vertically aligned carbon nanotubes (VA‐CNT) with a high specific surface area and iron(II) phthalocyanine (FePc) molecules. Pyrolyzing the composite easily transforms the adsorbed FePc molecules into a large number of iron coordinated nitrogen functionalized nanographene (Fe–N–C) structures, which serve as ORR active sites on the individual VA‐CNT surfaces. The catalyst exhibits a high ORR activity, with onset and half‐wave potentials of 0.97 and 0.79 V, respectively, versus reversible hydrogen electrode, a high selectivity of above 3.92 electron transfer number, and a high electrochemical durability, with a 17 mV negative shift of E _1/2 after 10 000 cycles in an oxygen‐saturated 0.5 m H₂SO₄ solution. The catalyst demonstrates one of the highest ORR performances in previously reported any‐nanotube‐based catalysts in acid media. The excellent ORR performance can be attributed to the formation of a greater number of catalytically active Fe–N–C centers and their dense immobilization on individual tubes, in addition to more efficient mass transport due to the mesoporous nature of the VA‐CNTs.     

The effect of chemical reaction on the mixing flow between aqueous solutions of acetic acid and ammonia

The basic characteristics of the reacting mixing flow of two streams were investigated. The reaction between aqueous solutions of ammonia and acetic acid, which produces ammonium acetate, was investigated in terms of the effect on the fluid–fluid interface of the mixing flow relative to fluids that did not react. The reaction between these solutions was negligibly exothermic, and there were minimal differences in density. The velocity field in the reacting mixing flow was quantitatively measured using high-speed time-resolved particle image velocimetry (PIV) and the behavior of the mixing flow was qualitatively investigated using laser-induced fluorescence (LIF). The jet width, the velocity field, the kinetic energy and the turbulent intensities are qualitatively estimated and discussed. It was found that the chemical reaction resulted in the suppression of the mixing flow.     

Numerical simulation on void bubble dynamics using moving particle semi-implicit method

In present study, the collapse of void bubble in liquid has been simulated using moving particle semi-implicit (MPS) code. The liquid is described using moving particles and the bubble–liquid interface was set to be vacuum pressure boundary without interfacial heat mass transfer. The topological shape of bubble can be traced according to the motion and location of interfacial particles. The time dependent bubble diameter, interfacial velocity and bubble collapse time were obtained under wide parametric range. The comparison with Rayleigh and Zababakhin's prediction showed a good agreement which validates the applicability and accuracy on MPS method in solving present momentum problems. The potential void induced water hammer pressure pulse was also evaluated which is instructive for further material erosion study. The bubble collapse with non-condensable gas has been further simulated and the rebound phenomenon was successfully captured which is similar with vapor-filled cavitation phenomenon. The present study exhibits some fundamental characteristics of void bubble hydrodynamics and it is also expected to be instructive for further applications of MPS method to complicated bubble dynamics problems.     

c-axis oriented ZnO formed in a rotating magnetic field with various rotation speeds

A rotating magnetic field was used to fabricate c-axis oriented zinc oxide. The influence of rotating speed on orientation structure was also examined. The aligned axes had the largest diamagnetic susceptibility, which axis was difficult to align with a static magnetic field. In c-axis oriented ZnO, the degree of orientation (Lotgering factor) in the green compact ranged from 0.2 to 0.5 along c-axis. The Lotgering factor increased with rotating speed. For all samples with the rotating magnetic field, the degrees of orientation increased up to above 0.9 after sintering at 1573 K.     

A Study on the Effect of Air on the Dynamic Motion of a MEMS Device and Its Shape Optimization

The authors propose a new design concept for controlling the deflection of a micro-membrane with the aid of its thickness distribution for realizing a prescribed design in the MEMS. As an example, the authors treat a micro air pump that comprises a micro-membrane. The membrane is actuated by an electrostatic force. The membrane deflects and thus the deflection is influenced by the air pressure and the electrostatic field. This is a highly complicated system. To find out a proper thickness distribution, the authors use the genetic algorithm that is appropriate to reduce the searching space of solution.