The integral experiment on beryllium with D-T neutrons for verification of tritium breeding

A clean benchmark experiment on beryllium was performed with D-T neutrons at the FNS facility of the Japan Atomic Energy Agency. The main objective was to verify the integral data related to the tritium production on lithium isotopes. Tritium production rates, as well as activation reaction rates were measured inside the beryllium assembly that was shaped as a pseudo-cylindrical slab with an area-equivalent diameter of 628 mm and a thickness of 355 mm. Experimental results were analyzed with a three-dimensional Monte Carlo transport code MCNP-4C and FENDL/MC-2.0, JENDL-3.2/3.3 neutron transport libraries. Evaluation of reaction rates was based on the cross section data taken from the JENDL Dosimetry File and ENDF B-VI data libraries. Analysis shows that all calculation combinations (transport and activation cross section libraries) used for evaluation of reaction rates give data that is agreeable with measured values within 10%.     

Robust digital control of a DC–DC buck converter with low frequency samplings

A robust DC?CDC converter which can covers extensive load change and also input voltage changes with one controller is needed. Then the demand to suppress output voltage change becomes still severer. We propose an approximate 2-degree-of-freedom (2DOF) digital controller which realized start-up response and dynamic load response independently. The controller makes a control bandwidth wider, and at the same time makes variations of the output voltage small at sudden changes of a load and an input voltage. In this paper, a new approximate 2DOF digital control system with additional zeros is proposed. Using the additional zeros, the second-order differential transfer characteristics between equivalent disturbances and a output voltage are realized. Therefore, the new controller makes variations of the output voltage smaller and the sudden changes of the load and the input voltage. This controller is actually implement on a DSP and is connected to the DC?CDC converter. Experimental results demonstrate that this type of digital controller can satisfy given severe specifications with low frequency sampling.     

MiR-10a in Pancreatic Juice as a Biomarker for Invasive Intraductal Papillary Mucinous Neoplasm by miRNA Sequencing

New biomarkers are needed to further stratify the risk of malignancy in intraductal papillary mucinous neoplasm (IPMN). Although microRNAs (miRNAs) are expected to be stable biomarkers, they can vary owing to a lack of definite internal controls. To identify universal biomarkers for invasive IPMN, we performed miRNA sequencing using tumor-normal paired samples. A total of 19 resected tissues and 13 pancreatic juice samples from 32 IPMN patients were analyzed for miRNA expression by next-generation sequencing with a two-step normalization of miRNA sequence data. The miRNAs involved in IPMN associated with invasive carcinoma were identified from this tissue analysis and further verified with the pancreatic juice samples. From the tumor-normal paired tissue analysis of the expression levels of 2792 miRNAs, 20 upregulated and 17 downregulated miRNAs were identified. In IPMN associated with invasive carcinoma (INV), miR-10a-5p and miR-221-3p were upregulated and miR-148a-3p was downregulated when compared with noninvasive IPMN. When these findings were further validated with pancreatic juice samples, miR-10a-5p was found to be elevated in INV (p = 0.002). Therefore, three differentially expressed miRNAs were identified in tissues with INV, and the expression of miR-10a-5p was also elevated in pancreatic juice samples with INV. MiR-10a-5p is a promising additional biomarker for invasive IPMN.     

Different feeding and gustatory responses to ecdysone and 20-hydroxyecdysone by larvae of the silkworm,Bombyx mori

The feeding and gustatory responses to ecdysone and 20-hydroxyecdysone were investigated in the silkworm,Bombyx mori. 20-Hydroxyecdysone reduced feeding response strongly in fourth- and fifth-instar larvae, whereas ecdysone had no effect on feeding response. 20-Hydroxyecdysone stimulated the R receptor, the receptor to feeding deterrents, to a great degree. By contrast, ecdysone was much less effective for stimulating the R receptor. These results indicate that ecdysone and 20-hydroxyecdysone have different effects on feeding response due to different interactions with mouthpart chemoreceptors.     

Properties of aqueous solutions of several salts of α,ω-alkanediol disulfates

Several salts of α,ω-sulfates, MO₃SO(CH₂)_n OSO₃M(n=12, 14, 16, 18, and M=Li, Na, and K) were prepared from the corresponding α,ω-alkane diols. The Krafft points of these α,ω-sulfates with common counterion as estimated by electroconductivity measurements increased with the increase of the hydrocarbon chain length, and the effect of the counterions on the Krafft points of the α,ω-sulfates with the same hydrocarbon chain length was in the order : Li<Na<K. Solutions of the α,ω-sulfates, except disodium dodecanediol disulfate, showed two break points corresponding to the first and second critical micelle concentration in each plot of the electroconductivity as a function of the concentration. The existence of the second break point suggested that another aggregation of rearrangement of the existing aggregates occurs in α,ω-sulfate solutions in addition to the usual micelle formation. The first and second break points of α,ω-sulfates with sodium counterion decreased logarithmically with increasing total number of methylene groups. The relationships were given as follows: log(first break point)=−0.138Nc−0.095; log(second break point)=−0.104Nc−0.251. The effect of the counterions upon the break points of α,ω-sulfates with the same hydrocarbon chain length was in accordance with their positions in the lyotropic series.     

Dynamic moduli for short fiber-CR composites

The dynamic moduli, E′ and E″, and tan δ for nylon–CR and PET–CR composites with unidirectional short fibers were studied as a function of temperature by using a Rheovibron. The temperature dependence of tan δ showed two dispersion peaks for nylon–CR composite. The peak at ?28°C corresponded to the main dispersion of CR and the peak at 100°C to the α-dispersion of nylon 6. For a PET-CR composite, in addition to the individual dispersion of CR and PET, a small and broad peak was observed at about 90°C. The angular dependence of E′ indicated that the short fibers assumed good orientation. The storage modulus for the composites was given by the parallel model as E′ = V_f′E_f + V_mE′_m., where E′_c, E′_f and E′_m were the storage modulus for the composite, fiber, and matrix and V_f and V_m were the volume fraction of fiber and matrix, respectively. In the transverse direction of fiber, the peak values of tan δ at ?28°C were given by the following equation; tan δ_c = tan δ_m ? δV_f, where tan δ_c and tan δ_m are the loss tangent for the composite and matrix, respectively, and α is coefficient depending on fiber type. The results indicated that a region with strong interaction was formed between fibers and CR matrix.     

An ergonomics study of thumb movements on smartphone touch screen

This study investigated the relationships between thumb muscle activity and thumb operating tasks on a smartphone touch screen with one-hand posture. Six muscles in the right thumb and forearm were targeted in this study, namely adductor pollicis, flexor pollicis brevis, abductor pollicis brevis (APB), abductor pollicis longus, first dorsal interosseous (FDI) and extensor digitorum. The performance measures showed that the thumb developed fatigue rapidly when tapping on smaller buttons (diameter: 9 mm compared with 3 mm), and moved more slowly in flexion–extension than in adduction–abduction orientation. Meanwhile, the electromyography and perceived exertion values of FDI significantly increased in small button and flexion–extension tasks, while those of APB were greater in the adduction–abduction task. This study reveals that muscle effort among thumb muscles on a touch screen smartphone varies according to the task, and suggests that the use of small touch buttons should be minimised for better thumb performance.     

Electrochemical reduction of nitrate on Pt(S)[n(1 1 1) × (1 1 1)] electrodes in perchloric acid solution

The electrochemical reduction of nitrate ion was studied by cyclic voltammetry on Pt(1 1 1) and [n(1 1 1) × (1 1 1)] stepped Pt surfaces, where n (=14, 10, 7, 6, 5, 4, 3, 2) is the number of terrace atoms, in 0.1 M HClO₄ + 10 mM KNO₃. The electrocatalytic nitrate reduction was found to hardly proceed on Pt(1 1 1) in the hydrogen adsorption region, while the electrocatalytic activity was improved with the increase in the step density. Inactivation was observed in the presence of adsorbed hydrogen or nitrate-derived reduced adsorbate, i.e. adsorbed NO, on (1 1 1) step sites. It was, therefore, concluded that the electrocatalytically active NO₃⁻ species does not adsorb on the (1 1 1) terraces but on the (1 1 1) monoatomic steps. The nitrate reduction current increased with the step density in a non-linear relationship. The overall current density at 0.21 V (RHE) corresponding to the peak potential of the main electrocatalytic nitrate reduction wave which was maximum at n = 2, abruptly increased with short terraces, i.e. n < 5, where the current wave of adsorbed hydrogen on the Pt stepped surface with comparatively narrow (1 1 1) terraces, denoted as H_nt, also appeared unmodified for n < 5 on voltammograms recorded in 0.1 M HClO₄ in the absence of nitrate.     

Mechanical Properties of Alumina/Silicon Carbide Whisker Composites

The improvement of mechanical properties of Al₂O₃/SiC whisker composites has been studied with emphasis on the effects of the whisker content and of the hot-pressing temperature. Mechanical properties such as fracture toughness and fracture strength increased with increasing whisker content up to 40 wt%. In the case of the high SiC whisker content of 40 wt%, fracture toughness of the sample hot-pressed at 1900° decreased significantly, in spite of densification, compared with one hot-pressed at 1850°. Fracture toughness strongly depended on the microstructure, especially the distribution of SiC whiskers rather than the grain size of the Al₂O₃ matrix.     

New method for selective growth of diamonds by microwave plasma chemical vapour deposition

Selective nucleation and deposition of diamonds were achieved on an SiO₂-patterned Si substrate. The substrate was pre-treated with an electric field in plasma to introduce diamond nuclei. This treatment did not affect the SiO₂ area. Consequently, diamonds grew only on the area where Si was exposed under the conventional conditions of diamond growth. The maximum nucleation density on the area of SiO₂was about 5 × 10⁷ cm⁻². The ratio of the selectivity was 2 × 10² or higher. This process will be useful and very promising for manufacturing diamond electronic devices.