Deposition of Lead Phosphate by Lead-Tolerant Bacteria Isolated from Fresh Water near an Abandoned Mine

Specialist bacteria can synthesize nanoparticles from various metal ions in solution. Metal recovery with high efficiency can be achieved by metal-tolerant microorganisms that proliferate in a concentrated metal solution. In this study, we isolated bacteria (Pseudomonas sp. strain KKY-29) from a bacterial library collected from water near an abandoned mine in Komatsu City, Ishikawa Prefecture, Japan. KKY-29 was maintained in nutrient medium with lead acetate and synthesized hydrocerussite and pyromorphite nanoparticles inside the cell; KKY-29 also survived nanoparticle synthesis. Quantitative PCR analysis of genes related to phosphate metabolism showed that KKY-29 decomposed organic phosphorus to synthesize lead phosphate. KKY-29 also deposited various metal ions and synthesized metal nanoparticles when incubated in various metal salt solutions other than lead. The present study considers the development of biotechnology to recover lead as an economically valuable material.     

Effect of matrix's type on the dynamic properties for short fiber-elastomer composite

The dynamic moduli, E′ and E″, and tan δ for PET–CR, PET–EPDM, and PET–UR composites with unidirectional short fibers were studied as a function of temperature by using a Rheovibron. The temperature dependence of tan δ showed three peaks for PET–elastomer composites. The peaks at the low temperature corresponded to the main dispersion of the respective matrixes and the peak at about 140°C to the α-dispersion of PET fiber. A small and broad peak observed at a temperature between 60 and 120°C may be caused by the relaxation of the interface region between fibers and matrix. The longitudinal storage modulus for the composite E was given by the parallel model as \documentclass{article}\pagestyle{empty}\begin{document}$ {\rm E'}_\parallel = V_f \cdot E'_f + V_m \cdot E'_m $\end{document}, where E and E are the storage moduli for fiber and matrix and V_f and V_m are the volume fraction of fiber and matrix, respectively. In the transverse direction of fibers, the composite modulus E was expressed by the logarithmic law of mixing as follows: \documentclass{article}\pagestyle{empty}\begin{document}$ \log E'_ \bot = V_f \cdot \log E'_f + V_m \cdot \log E'_m $\end{document}. The peak values of tan δ from the main dispersion of the respective matrixes were given by the equation, (tan δ_⊥max)_c/(tan δ_max)_m 1 ? β · V_f, where (tan δ_⊥max)_c and (tan δ_max)_m are the maximum values of the loss tangent for the composite and matrix, respectively, and β is coefficient depending on matrix's type. The β value of PET–CR composite is the largest one among those of the composites.     

Application of magnetic nanoparticles to gene delivery

Nanoparticle technology is being incorporated into many areas of molecular science and biomedicine. Because nanoparticles are small enough to enter almost all areas of the body, including the circulatory system and cells, they have been and continue to be exploited for basic biomedical research as well as clinical diagnostic and therapeutic applications. For example, nanoparticles hold great promise for enabling gene therapy to reach its full potential by facilitating targeted delivery of DNA into tissues and cells. Substantial progress has been made in binding DNA to nanoparticles and controlling the behavior of these complexes. In this article, we review research on binding DNAs to nanoparticles as well as our latest study on non-viral gene delivery using polyethylenimine-coated magnetic nanoparticles.     

Transmission electron microscopic observations of nanobubbles and their capture of impurities in wastewater

Unique properties of micro- and nanobubbles (MNBs), such as a high adsorption of impurities on their surface, are difficult to verify because MNBs are too small to observe directly. We thus used a transmission electron microscope (TEM) with the freeze-fractured replica method to observe oxygen (O₂) MNBs in solutions. MNBs in pure water and in 1% NaCl solutions were spherical or oval. Their size distribution estimated from TEM images close to that of the original solution is measured by light-scattered methods. When we applied this technique to the observation of O₂ MNBs formed in the wastewater of a sewage plant, we found the characteristic features of spherical MNBs that adsorbed surrounding impurity particles on their surface.     

Structural chirality of cholesteric liquid crystal produces atropisomerism: Chiroptical polyisocyanides from achiral monomer in cholesteric liquid crystal matrix

1-Naphthyl isocyanide was polymerized with Ni(II) catalyst in a cholesteric matrix at the liquid crystal (LC) temperature range. The resultant polymers showed optical activity. In this reaction, the structural chirality of cholesteric LC effectively functions to impart one-handed helicity on the corresponding polymers as an optically active atropisomer.     

Analysis of proton exchange membrane fuel cell catalyst layers for reduction of platinum loading at Nissan

The biggest issue that must be addressed in promoting widespread use of fuel cell vehicles (FCVs) is to reduce the cost of the fuel cell system. Especially, it is of vital importance to reduce platinum (Pt) loading of catalyst layers (CLs) in the membrane electrode assembly (MEA) of a proton exchange membrane fuel cell (PEMFC). In order to lower the Pt loading of the MEA, mass transport of reactants related to the performance in high current density should be enhanced significantly as well as kinetics of the catalyst, which can result in the better Pt utilization and effectiveness. In this study, we summarized our analytical approach and methods for reduction of Pt loading in CLs. Microstructure, mass transport properties of the reactants, and their relation in CLs were elucidated by applying experimental analyses and computational methods. A simple CL model for I–V performance prediction was then established, where experimentally elucidated parameters of the microstructure and the properties in CLs were taken into account. Finally, we revealed the impact of lowering the Pt loading on the transport properties, polarization, and the I–V performance.     

Determination of optical purity and absolute configuration of natural 12‐hydroxystearic acid by the 1H NMR anisotropy method

The enantiopure of (R)‐(?) MαNPA was allowed to react with racemic 18‐(tert‐butyldimethylsilyloxy)‐5‐octadecayne‐7‐ol which was derived from dodecane‐1,12‐diol, yielding diastereomeric esters mixture. These racemic esters were easily separated by HPLC on silica‐gel. The absolute configurations of the first‐eluted diastereomeric esters from the separated esters were determined using ¹H NMR anisotropy method. Analysis on ¹H NMR spectra and HPLC elution time of the synthesized esters and those of MαNP ester derived from natural methyl‐12‐hydroxystealate showed that the absolute configuration of natural 12‐hydroxystearic acid was R form, and the enantiomeric excess was over 99%.     

Effect of styrene–acrylonitrile on the electrical resistivity of polycarbonate/multiwalled carbon nanotube composites

Multiwalled carbon nanotube (MWCNT)‐filled polycarbonate (PC)/styrene–acrylonitrile (SAN) blends with a wide range of blend compositions were prepared by melt mixing in a rotational rheometer, and the effect of SAN on the electrical properties of the PC/MWCNT composites was studied. The structure/electrical property relationship was investigated and explained by a combination of MWCNT localization and blend morphology. Transmission electron micrographs showed selective localization of MWCNTs in the PC phase, regardless of the blend morphology. When the SAN concentration was 10–40 wt %, which corresponded to sea‐island (10–30 wt %) and cocontinuous (40 wt %) blend morphologies (PC was continuous in both structures), the electrical resistivity decreased with increases in the SAN content. The concept of an effective volume concentration of MWCNTs was used to explain this effect. When the SAN concentration was 70 wt % or higher, the electrical resistivity was very high because MWCNTs were confined in the isolated PC particles. In addition, SAN was replaced by other polymers [polystyrene, methyl methacrylate/styrene, and poly(methyl methacrylate)]; these yielded similar blend morphologies and MWCNT localization and showed the generality of the concept of effective concentration in explaining a decrease in the electrical resistivity upon the addition of a second polymer. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Fabrication and piezoelectric properties of BaTiO3/BaTiO3-Bi(Mg1/2Ti1/2)O3-BiFeO3 composites

We fabricated xBaTiO₃ (BT)/(1-x)[BaTiO₃-Bi(Mg_1/2Ti_1/2)O₃-BiFeO₃] (BT-BMT-BF)?+?0.1?wt%MnCO₃ composites by spark plasma sintering and investigated the effect of BT content x, BT powder size, and BT-BMT-BF composition on piezoelectric properties. For xBT/(1-x)(0.3BT-0.1BMT-0.6BF) +?0.1?wt%MnCO₃ (x?=?0–0.75) composites with a 0.5-µm BT powder, the dielectric constant was increased with x, and the relative density was decreased at x?=?0.67 and 0.75, creating optimum BT content of x?=?0.50 with a piezoelectric constant d₃₃ of 107?pC/N. When a larger 1.5-µm BT powder was utilized for the composite with x?=?0.50, the d₃₃ value increased to 150?pC/N due to the grain size effect of the BT grains. To compensate for a compositional change from the optimum 0.3BT-0.1BMT-0.6BF due to partial diffusion between the BT and 0.3BT-0.1BMT-0.6BF grains, a 0.5BT/0.5(0.275BT-0.1BMT-0.625BF)?+?0.1?wt%MnCO₃ composite with the 1.5-µm BT powder was fabricated. We obtained an increased d₃₃ value of 166?pC/N. These results provided a useful composite design to enhance the piezoelectric properties.