Effect of surface configuration on heat transfer by the condensation of steam over fluted surfaces part II

Heat transfer characteristics of fluted tubes have been determined by a pilot-plant study. Film coefficients (inside, outside and overall) have been expressed as a function of average liquid velocity. The performance of fluted tubes has been evaluated with respect to flute geometry and operating conditions by considering the hydrodynamic state of the condensate film. A “geometric criterion” has been formulated to compare fluted tubes of different geometric designs with respect to their performance in heat transfer.     

Utilization of waste loquat (Eriobotrya Japonica Lindley) kernels as substrate for scleroglucan production by locally isolated Sclerotium rolfsii

Present study mainly focused on investigating the feasibility of waste loquat kernels as substrate in submerged culture of Sclerotium rolfsii MT-6 for scleroglucan production. Loquat kernel contained high protein (22.5%) and total carbohydrate (71.2%) contents. Dried and powdered kernels were subjected to acid hydrolysis with 2 N HCl. The obtained hydrolysate was used for the preparation of loquat kernel extract (LKE) and detoxified loquat kernel extract (DLKE). S. rolfsii MT-6 was isolated from fermented squash (Cucurbita pepo). Optimal conditions for scleroglucan production were initial pH 5.0, shaking speed 150 rpm, 28°C, and cultivation time of 72 hr. Production media prepared with DLKE or LKE gave maximum biomass concentrations of 17.06 and 16.21 g/L, and maximum scleroglucan concentrations of 12.08 and 10.53 g/L, respectively. DLKE was also favorable substrate for mycelial growth in a uniform pellet form. This is a first report on the application of waste loquat kernels as scleroglucan production substrate and on the use of a local S. rolfsii isolate for this purpose.     

Removal of basic dyes from aqueous solutions by crosslinked‐acrylic acid/acrylamidopropane sulfonic acid hydrogels

In this study, Acrylic acid (AA)/2‐acrylamido‐2‐methlypropane sulfonic acid (AMPS) hydrogels were prepared by free radical polymerization in aqueous solutions of AA, AMPS, and N,N‐methylenebisacrylamide (NMBA) as crosslinker. Potassium persulfate (PPS)/potassium bisulfide (PBS) were used as initiator and accelerator pair. The water absorption capacities and dye adsorption properties of the hydrogels were investigated. Adsorption properties of the hydrogels were evaluated by depending on different adsorption conditions such as different initial dye concentration and contact time. The concentrations of the dyes were determined using UV/Vis Spectrophotometer at wavelength 530 nm for safranine T (ST) and 622 nm for brilliant cresyl blue (BCB). Adsorption kinetic studies showed that pseudo‐first order kinetic model is suitable to explain the adsorption kinetic data of the hydrogels. Langmuir and Freundlich isotherm models were used to describe adsorption data. The result revealed that the adsorption of basic dyes onto hydrogels fit very well both Langmuir and Freundlich isotherms. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Flocculation of fine particles in ceramic wastewater using new types of polymeric flocculants

It appears to be quite a few national and international studies were reported regarding flocculation and settling properties of ceramic industry wastewater containing various mineral matters. Cleaning of ceramic industry wastewaters with ever increasing environmental standards needs effective and economical solid–liquid separation processes. In this study, quantity and type of optimum flocculant concentration were investigated for solid–liquid separation of Umpac ceramic plant (located at Usak, Turkey) wastewaters. A new generation of flocculants namely unique molecular architecture (UMA) are used to obtain high settling velocity along with high solid content waste and circulation water with low turbidity values. Zeta potential of the tailings including quartz, feldspar, clorite, and mica was also measured at different pH values. The flocculation tests were performed in the presence of different types of polymers at different polymer dosages. It seems that Magnafloc 5250 shows higher performance than the anionic flocculant SPK 508 and other anionic UMA flocculants Magnafloc 6260 and Magnafloc 3230. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Post-buckling behavior of carbon fiber epoxy composite plates

In this study, the pre-buckling and post-buckling behaviors of layered composite plates which were made of woven carbon fiber fabric with a circular hole in the middle were investigated experimentally and numerically. Firstly, load-displacement graphs of composite plates with different hole diameters were experimentally obtained under compressive load. Then the numerical load-displacement graphs of the plates were found with the ANSYS package program which used the finite element method. As a result, after linear buckling experimental and numerical results were found to be compatible with each other. In addition, damage behavior of plates after buckling with the aid of Tsai-Wu damage criterion was obtained similar to experimental results. The increase in hole diameter did not change the load-displacement behavior characteristics of the plates after buckling. However, it has reduced maximum damage load and maximum failure displacement. The stress at the perimeter of the hole increased significantly with the increase of the vertical displacement with immediately after the buckling but later was not significantly affected by this increase.

     

Three-parameter (3P) weibull distribution for characterization of strength of ceramics showing R-Curve behavior

Strength distribution of advanced ceramics is commonly characterized by two-Parameter (2P) Weibull distribution. However, deviation of strength distribution from 2P-Weibull distribution may occur in ceramics due to various mechanisms. R-curve behavior is one of these mechanisms where increase of fracture resistance with the extension of crack occurs. In such cases, 2P-Weibull distribution may not be the best fitting distribution function based on the goodness-of-fitness tests. This article examines the effectiveness of three-parameter (3P) Weibull distribution function for fitting the strength variation due to R-curve effect by using experimental and virtual strength data. The effect of Weibull parameters, degree of increase in crack resistance and number of samples on effectiveness of fitting via 3P-Weibull distribution is investigated. It is reported that 3P-Weibull distribution function fits the strength distribution better than 2P-Weibull distribution function for materials showing R-curve behavior when the crack resistance curve is steep and Weibull modulus is high. Furthermore, it is shown that at least 100 samples should be used for a reliable estimate when the material exhibits R-curve behavior.     

Caregivers’ attitudes toward potential robot coworkers in elder care

Technological advances in robotics increase progressively. Elder care is one of the work areas which have potential to involve robotic workforce. So, it is important to focus on interaction between humans and potential robot workers to prepare the organization for possible challenges. The current study examined the relationships between trust in robots and anthropomorphism of robots, intention to work with robots and preference of automation levels. For this purpose, 102 caregivers who work for elder care in a nursing home (aged between 19 and 40) participated in an experimental study. According to the results, anthropomorphism of robots did not make any difference in terms of trust in them. Trust in robots was significantly related to intention to work and preference of automation levels. Organizations may consider employees’ trust in robots as an important factor before adapting them to workplace area.

     

The interleukin-10 promoter genotype predicts diastolic dysfunction in maintenance hemodialysis patients

Interleukin-10 (IL-10) predominantly acts as an anti-inflammatory factor. Polymorphisms in the IL-10 gene promoter determine quantitative cytokine production. Doppler echocardiography and tissue Doppler imaging (TDI) are superior to conventional echocardiography to evaluate diastolic dysfunction. The IL-10 gene promoter polymorphism at position (-1082) was studied for its association with conventional and Doppler echocardiographic and TDI parameters in 112 hemodialysis (HD) patients. Blood pressure, serum C-reactive protein (CRP), and albumin levels were also examined for the association study. The genetic association study showed that among the HD patients, there was no difference in the prevalence of systolic and diastolic dysfunction between genotypes on conventional echocardiography. However, using Doppler echocardiography and TDI, high producers for the IL-10 -1082 promoter (-1082/GG) have higher E velocities, E/A values, lateral, and septal E' velocities and a lower isovolumic ventricular relaxation time than low (-1082/AA) and intermediate producers (-1082/GA). Significantly higher levels of serum CRP levels and lower plasma albumin levels were found in low and intermediate producers for the IL-10 -1082 promoter than high producers. The IL-10 genotype may balance the effects of inflammatory cytokines on the myocardium and may be a determinant of LV function in HD patients.     

Morphofunctional structure of the lingual papillae in three species of South American Camelids: Alpaca,guanaco, and llama

The aim of this study was to compare the anatomical and functional characteristics of the lingual papilla among the Camelidae. For this purpose, tongues of alpaca, guanaco, and llama were used. Numerous long and thin filiform papillae were located in the median groove and none were detected on the rest of the dorsal surface of the lingual apex in alpaca. Secondary papillae originated from the base of some filiform papillae on the ventral surface of alpaca tongue. The bases of some filiform papillae of the lateral surface of the lingual apex were inserted into conspicuous grooves in guanaco and tips of filiform papillae on the dorsal surface of the lingual body were ended by bifurcated apex. On the dorsal surface of the lingual apex of llama, there were no filiform papillae but there were numerous filiform papillae on both the lateral margins of the ventral surface of the lingual apex. Fungiform papillae were distributed randomly on dorsal lingual surface and ventral margins of the tongues of all camelid species. Lenticular papillae were located on the lingual torus and varied in size and topographical distribution for each species. Circumvallate papillae had irregular surfaces in llama and alpaca, and smooth surface in guanaco. In conclusion, llama and alpaca tongues were more similar to each other, and tongues of all camelid species displayed more similarities to those of Bactrian and dromedary camels in comparison with other herbivores and ruminants. Microsc. Res. Tech. 79:61–71, 2016. © 2015 Wiley Periodicals, Inc.