CREEP CRACK PROPAGATION IN CONVENTIONAL CAST AND DIRECTIONALLY SOLIDIFIED SUPERALLOY RENE 80

The creep crack propagation in superalloy René80 of two different microstructures,i.e.,equiaxed grain structure by conventional casting and columnar grain by directionalsolidification,was investigated under static load at 1123 K.The creep crack growth rate,da/dt,seems to be correlated with the stress intensity factor,K.The creep crack growth ratein the directionally solidified alloy is lower than that in the conventional cast alloy,owing tothe elimination of transverse grain boundaries.The effect of microstructure on creep crackpropagation has also been discussed.     

THERMODYNAMICS OF MARTENSITIC TRANSPORMATION IN β-Cu BASE ALLOYS

提出对β-Cu基合金热弹性马氏体相变的热力学处理。计算了Cu-Zn,Cu-Al及Cu-Zn-Al合金马氏体相变驱动力,T_0温度及M_s温度,M_s的计算值与实验值符合很好。母相有序降低Cu-Zn和Cu-Zn-Al的M_s,但升高Cu-Al的M_s(T_0)。并简介了两种估算非化学自由能的方法。     

(Ⅰ+Ⅱ)复合型氢致开裂的研究

本文研究了30CrMnSiA高强钢在纯Ⅰ型、纯Ⅱ型和(Ⅰ+Ⅱ)复合型加载条件下的氢致开裂。实验表明,在1NH_2SO_4溶液中预充氢的试件在上述加载条件下均表现出氢致脆性。纯Ⅱ型氢致开裂门槛值K_(ⅡH)/K_(ⅡX)=0.27,与纯Ⅰ型门槛值K_(ⅠH)/K_(ⅠX)=0.29基本相同,而在K_Ⅱ/K_Ⅰ比值为0.27,0.4和0.81时,(Ⅰ+Ⅱ)复合型氢致开裂门槛值分别为0.36,0.41和0.37,表明纯Ⅰ型和纯Ⅱ型具有更高的氢脆敏感性。最后用自Ⅰ型加载向Ⅱ型过渡时,三轴张力和塑性变形程度这二个矛盾因素对氢致开裂的共同作用解释了上述实验结果。     

ELECTRON MICROANALYSIS FOR LASER MELTED ZONE IN 45 STEEL WITH Fe-Ni-Cr COATING

The Fe-Ni-Cr coating laver has been alloyed with 45 steel base metal by transverse.flow typeCO_2 gas laser of maximum output 5kW.The characteristics of the melted zone and the es-sence of the“bright band”has been investigated using the electron microscopy.The resultsshow that the“bright band”belongs to the melted zone and is a vertical section of the planecrystal,The width of the“bright band”equals the height of the plane crystal,which decreaseswith the increase of laser beam scanning rate and the decrease of laser power.This has beenexplained in terms of constitutional supercooling G/R.     

A STUDY ON THE INITIAL CARBIDES FORMED DURING ISOTHERMAL DECOMPOSITION OF AUSTENITE IN CHROMIUM STEEL

采用X射线衍射法对七种铬钢进行了研究.进一步证实了关于铬钢中奥氏体等温分解过程和Cr/C比值有关的结果.采用新的观点进行解释. 同时还发现上述过程也和奥氏体的分解温度(或过冷度)有关(图3).Cr/C比值低的奥氏体在图3中所示之全部温度范围内,初期都形成(Fe,Cr)_3C.并且能够大致地预测Cr/C比值高的奥氏体初期在高温范围内将形成(Cr,Fe)_(23)C_6,在中温范围内将形成(Cr,Fe)_7C_3,在低温范围内将形成(Fe,Cr)_3C.Cr/C比值适中的奥氏体初期在高温和中温范围内都形成(Cr,Fe)_7C_3,在低温范围内形成(Fe,Cr)_3C. 并且初步认为在所有的情况下,都存在从一相至另一相的由两相构成的过渡区.     

THEORETICAL CALCULATION OF POINT DEFECTS IN Ni_3Al

Equilibrium equation of point defects in Ll_2 type intermetallic compounds was established tocalculate the relations of the concentration of antisite defects and vacancies and bulk composi-tion in Ni_3Al.The examination of temperature effects on the point defects cleared up the mis.understanding of the properties of the“constitutional point defects”in Ni_3Al.     

NiTi形状记忆合金的相变温度滞后

用透射电镜、正电子湮没和电阻测量,研究了NiTi形状记忆合金的组织结构与相变滞后的关系结果表明,经不同制度时效处理的组织,其相变温度滞后大小的顺序是:片状马氏体>R相>束状马氏体。Ti_(11)Ni_(14)相质点周围的共格应力场对这些相的可逆转变起障碍作用。正电子湮没Doppler展宽能谱S参数值与试样的温度滞后值之间存在线性关系,从而确认Ti_(11)Ni_(14)相析出的错配位错密度及由此而建立的晶体中弹性应力场分布是决定NiTi合金相变温度滞后的主要因素。     

Ni3Al合金中晶界与位错交互作用的研究

运用嵌入原子法势函数和静态驰豫最陡梯度的计算方法,原子模拟了Ni_3Al合金中晶界与位错的交互作用.主要研究了晶界与位错交互作用的能量特征、晶界结构单元的畸变行为和晶界附近位错的核心结构,并分析讨论了各种因素对它们的影响以及与Ni_3Al晶界韧脆行为之间的关系     

A machine vision approach to seam tracking in real-time in PAW of large-diameter stainless steel tube

Manual monitoring and seam tracking through watching weld pool images in real-time, by naked eyes or by industrial TV, are experience-depended, subjective, labor intensive, and sometimes biased. So it is necessary to realize the automation of computer-aided seam tracking. A PAW (plasma arc welding) seam tracking system was developed, which senses the molten pool and the seam in one frame by a vision sensor, and then detects the seam deviation to adjust the work piece motion adaptively to the seam position sensed by vision sensor. A novel molten pool area image-processing algorithm based on machine vision was proposed. The algorithm processes each image at the speed of 20 frames/second in real-time to extract three feature variables to get the seam deviation. It is proved experimentally that the algorithm is very fast and effective. Issues related to the algorithm are also discussed.     

使用人工神经网络对强力旋压有限元模拟进行参数预选

在筒形件强力旋压领域内，介绍了使用人工神经网络的手段，在MARC有限元模拟的前处理中实现参数预选的方法。作为与有限元模拟相结合的旋压智能化设计的一项关键技术，能够达到减少有限元模拟的误差和工作量的目的。