Transesterification of Palm-based Methyl Palmitate into Esteramine Catalyzed by Calcium Oxide Catalyst

The technology for transesterification reactions between methyl esters and alcohols is well established by using classical homogeneous alkaline catalysts, which provide high conversion of methyl esters to specialty or nonindigenous esters. However, in certain products where the purity of the esters is of concern, the removal of homogeneous catalysts after the completion of the reaction is a challenge in terms of production cost and water footprint. Therefore, a study to investigate the potential of heterogeneous catalysts was conducted on reactions between methyl palmitate and triethanolamine. The degree of basicity and active surface area of calcium oxide (CaO), zinc oxide (ZnO), and magnesium oxide (MgO) were first characterized by using temperature-programmed desorption (TPD-CO₂) and Brunauere–Emmett–Teller (BET), respectively. Among the metal oxides investigated, the CaO catalyst showed the best catalytic activity toward the transesterification process as it gave the highest conversion of methyl palmitate and yielded fatty esteramine compositions similar to the conventional homogeneous catalyst. The optimum transesterification condition by using the CaO catalyst utilized a lower vacuum system of approximately 200 mbar, which could minimize a considerable amount of energy consumption. Furthermore, low CaO dosage of 0.1% was able to give a conversion of 94.5% methyl ester and formed esteramine at 170 °C for 2 h. Therefore, the production of esterquats from esteramine may become more economically feasible through the methyl ester route by using the CaO catalyst, which can be recycled three times.     

Synthesis and characterization of novel copolymers with the trimethylsilyl group for deep‐UV photoresists

N‐(4‐Acetoxyphenyl) maleimide (APMI) and three kinds of comonomers bearing a trimethylsilyl group were copolymerized at 60°C in the presence of azobisisobutyronitrile (AIBN) as an initiator in 1,4‐dioxane to obtain the three IP, IIP, and IIIP copolymers. These copolymers were removed from the acetoxy group in a transesterification process into new IVP, VP, and VIP copolymers with a pendant hydroxyl group. Two modified processes were adopted to prepare photoresists using these copolymers. The first process involved mixing the dissolution inhibitor, o‐nitrobenzyl cholate, with the new copolymers. Second, o‐nitrobenzyl cholate was introduced into the copolymers using 1,8‐diazabicyclo[5.4.0]undec‐7‐ene (DBU) in dimethylformamide (DMF). The cyclic maleimide structure is responsible for the high thermal stability of these copolymers. After irradiation using deep–UV light and development with aqueous Na₂CO₃ (0.01 wt %), the developed patterns showed positive images and exhibited good adhesion to the silicon wafer without using any adhesion promoter. The resolution of these resists was at least 0.8 μm and an oxygen‐plasma etching rate was 1/5.3 to that of hard‐baked HPR‐204. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2791–2798, 2002; DOI 10.1002/app.10255     

Standard reference materials for cements

The eight portland cements and two calcium aluminate cements in the Standard Reference Material (SRM) 1880 series are among the most popular SRMs in the catalog of the National Institute of Standards and Technology (NIST) Standard Reference Materials Program. Numerous laboratories rely on them for elemental analysis and qualification for ASTM C 114-00 Standard Test Methods for Chemical Analysis of Hydraulic Cement. NIST has collected new candidate materials from around the world and partnered with Construction Technology Laboratories (CTL) in their preparation and certification. This paper describes the procedures taken at NIST and CTL to prepare and test materials for certification including the homogeneity testing, the X-ray fluorescence methods and the statistical data analysis performed for value assignment.     

Enhanced corrosion prevention effect of polysulfone–clay nanocomposite materials prepared by solution dispersion

A series of polymer–clay nanocomposite (PCN) materials containing polysulfone (PSF) and layered MMT clay were successfully prepared by effectively dispersing inorganic nanolayers of MMT clay in an organic PSF matrix via a solution dispersion technique. The synthesized PCN materials were subsequently investigated with a series of characterization techniques, including Fourier transform infrared (FTIR) spectroscopy, wide‐angle powder X‐ray diffraction (XRD) and transmission electron microscopy (TEM). The prepared PCN coatings with low clay loading (1 wt %) on cold‐rolled steel (CRS) were found to be superior in corrosion prevention to those of bulk PSF, based on a series of electrochemical measurements of corrosion potential, polarization resistance, corrosion current and electrochemical impedance spectroscopy (EIS) in a 5 wt % aqueous NaCl electrolyte. The effects of material composition on the molecular barrier, mechanical strength and optical clarity of PSF and PCN materials, in the form of membranes, was also studied by molecular permeability analysis (GPA), dynamic mechanical analysis (DMA) and UV‐Visible transmission spectra, respectively. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 631–637, 2004     

Study of the composition effect of glass ceramic and silver on poly(vinyl butyral) thermal degradation with thermogravimetric analysis

The thermal degradation of poly(vinyl butyral) (PVB)/glass ceramic, PVB/Ag, and PVB/glass ceramic/Ag composites was investigated with thermogravimetric analysis in nitrogen and air. Thermogravimetric data revealed that the compositions of both inorganic materials in air could greatly influence the thermal degradation of PVB. The degradation reactions of PVB/ceramic and PVB/Ag composites began earlier and accelerated rapidly at lower temperatures. The overall degradation period was obviously shortened for the thermal degradation of PVB/Ag in air, whereas a longer time was required for the PVB/ceramic composite than for PVB. Moreover, dual effects of ceramic and Ag on the thermal degradation of PVB were observed for PVB/ceramic/Ag composites. In addition, the catalytic effects of ceramic and Ag on the degradation reaction of PVB in air were verified with a kinetic analysis. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2142–2149, 2004     

Preparation and characterization of methoxy‐poly(ethylene glycol) side chain grafted onto chitosan as a wound dressing film

Chitosan has received extensive attention as a biomedical material; however, the poor solubility of chitosan is the major limiting factor in its utilization. In this study, chitosan‐based biomaterials with improved aqueous solubility were synthesized. Two molecular weights (750 Da and 2000 Da) of methoxypoly(ethylene glycol) (mPEG) were grafted onto chitosan (mPEG‐g‐chitosan) to form a ～100‐μm‐thick plastic film as a wound dressing. The chemical structures of the mPEG‐g‐chitosan copolymers were confirmed using Fourier transform infrared spectroscopy (FTIR), and the thermal properties were characterized using thermogravimetry analysis (TGA). Their microstructures were observed using scanning electron microscopy (SEM). The other properties were analyzed via the swelling ratio, tensile strength, elongation, and water vapor transmission rate (WVTR). Biocompatibility evaluations through biodegradability, cytotoxicity, and antimicrobial effect studies were also performed. The obtained mPEG‐g‐chitosan copolymers were soluble in slightly acidic aqueous solutions (pH～6.5) at a concentration of 10 wt %. The optimal mPEG‐g‐chitosan hydrogels had swelling ratios greater than 100% and WVTRs greater than 2000 g/m²/day. Their performance against Staphylococcus aureus will be subjected to further improvements with respect to medical applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42340.     

Characterizations of TiO2/SiO2/Ni–Cu–Zn Ferrite Composite for Magnetic Photocatalysts

The TiO₂/SiO₂/Ni–Cu–Zn ferrite composite for magnetic photocatalysts with high photocatalytic activity is successfully prepared in this study. The composite are composed of spherical or elliptical Ni–Cu–Zn ferrite nanoparticles about 20–60 nm as magnetic cores, silica as barrier layers with thickness of 15 nm between the magnetic cores and titania shells with thickness approximately 1.5 nm. Photodegradation examination of TiO₂/SiO₂/ Ni–Cu–Zn ferrite composite was carried out in methylene blue (MB) solutions illuminated under a Xe arc lamp with 35 W and color temperature of 6000 K. The results indicated that about 47.1% of MB molecules adsorbed on the TiO₂/SiO₂/Ni–Cu–Zn ferrite composite within 30 min mixing due to it higher pore volume of 0.034 cm³/g, and after 6 h Xe lamp irradiation, 83.9% of MB 16.1% was photodegraded. Compared with the TiO₂ /Ni–Cu–Zn ferrite composite, the TiO₂/SiO₂/Ni–Cu–Zn ferrite composite with silica barrier layer prohibited the photodissolution and enhanced the photocatalytic ability. The magnetic photocatalyst shows high photocatalytic efficiency that the apparent first‐order rate constant k_obs is 0.18427 h^?1, and good magnetic property that the saturation magnetization (M_s) of is 37.45 emu/g, suggesting the magnetic photocatalyst can be easily recovered by the application of an external magnetic field.     

Graphene coating assisted injection molding of ultra‐thin thermoplastics

High strength light weight parts are critical for the development of new technologies, particularly electronic devices, such as laptop computers, smart phones, and tablet devices. Injection molded plastics and composites are excellent choices for mass producing such parts. As the part thickness decreases from traditional injection molding (>2 mm thickness) to thin wall molding (～1 mm thickness), and lastly, to ultra‐thin wall molding (<0.5 mm thickness), avoiding incomplete filling (short shots) becomes more challenging. Even though, methods exist today for molding thin‐wall plastic parts (i.e., fast heating/fast cooling injection molding), they require multiple steps resulting in a noncost efficient process. In this article, we demonstrate the technical feasibility of using graphene coating to facilitate flow, by promoting slip at the mold walls. We evaluate the influence of coated and uncoated mold inserts on fiber orientation. We present experimental results using un‐reinforced polypropylene and a 40% by weight carbon fiber reinforced polycarbonate/acrylonitrile butadiene styrene. POLYM. ENG. SCI., 55:1374–1381, 2015. © 2015 Society of Plastics Engineers     

An intelligent skin‐color capture method based on fuzzy C‐means with applications

Consumer behavior is complicated. In the cosmetic market, personal intuition and fashion trends for color selection are guidelines for consumers. A systematic method for female facial skin‐color classification and an application in the makeup market are proposed in this study. In this article, face recognition with a large number of images is first discussed. Then, an innovative method to capture color at selected points is presented and complexion‐aggregated analysis is performed. This innovative method is an extension of face‐recognition theory. Images in RGB format are converted to CIELAB format during data collection and then Fuzzy C‐means theory is used to cluster and group the data. The results are classified and grouped in Lab value and RGB index. Two programs are created. The first program, “FaceRGB,” captures color automatically from images. The second program, “ColorFCM,” clusters and groups the skin‐color information. The results can be used to assist an expert system in the selection of customized colors during makeup and new‐product development.     

Fiber and film developments from immiscible blends of cellulose acetate propionate and poly(butylene terephthalate)

Binary blends of cellulose acetate propionate (CAP) and poly(butylene terephthalate) (PBT) in the composition range of 5–15 wt % for CAP were prepared in the form of films and fibers by compression molding and spinning, respectively. The presence of two invariant glass‐transition temperatures corresponding to the CAP and PBT components and viscosities lower than those of the neat PBT of the CAP–PBT blends implied that the CAP–PBT blends were immiscible. Moreover, the crystallinity of the PBT component was higher in the spun fibers than in the films; this was possibly due to the different cooling methods or the chain orientation in the spinning process. In the meantime, the CAP component could not undergo crystallization because of its rigid structure and alkyl substituents. For the CAP–PBT films, the amorphous CAP was present as dispersed particles in the PBT matrix; but it became rods in the spun fibers. In addition, the presence of the amorphous CAP resulted in a decrease in the tensile strength and an increase in the elongation at break for the CAP–PBT fibers. The CAP–PBT films and fibers could be applied in a wide range of applications requiring renewable properties. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45013.