Mixed powder coating film using thermoplastic polyester and its alkaline resistance

To improve alkaline resistance, a newly mixed powder coating film using thermoplastic polyethylene terephthalate (PET) was investigated. Two kinds of polyvinyl butyral (PVB) and two kinds of polyamide (PA) were chosen as the secondary polymer. The melting temperatures (T _ms) of these materials were lower than that of primary PET polymer so the mixed powder coating was able to form a dual phase film through a fluidized bed coating process. Microscope and Fourier transform infrared spectroscopy (FTIR) observations revealed that the dual phase structure was indeed successfully formed and there was a secondary layer over the entire surface area of the film. This mixed powder coating film significantly enhanced the alkaline resistance to an environment filled with NaOH solution at 40°C in which a secondary material would be effective in protecting the film. With regard to both alkaline resistance and film formability, PET/PVB was superior to the PET/PA mixture.     

Fracture Energies of Tape-Cast Silicon Nitride with β-Si3N4 Seed Addition

The fracture energies of the tape-cast silicon nitride with and without 3 wt% rod-like β-Si₃N₄ seed addition were investigated by a chevron-notched-beam technique. The material was doped with Lu₂O₃–SiO₂ as sintering additives for giving rigid grain boundaries and good heat resistance. The seeded and tape-cast silicon nitride has anisotropic microstructure, where the fibrous grains grown from seeds were preferentially aligned parallel to the casting direction. When a stress was applied parallel to the fibrous grain alignment direction, the strength measured at 1500°C was 738 MPa, which was almost the same as room temperature strength 739 MPa. The fracture energy of the tape-cast Si₃N₄ without seed addition was 109 and 454 J/m² at room temperature and 1500°C, respectively. On the contrary, the fracture energy of the seeded and tape-cast Si₃N₄ was 301 and 781 J/m² at room temperature and 1500°C, respectively, when a stress was applied parallel to the fibrous gain alignment. The large fracture energies were attributable primarily to the unidirectional alignment fibrous Si₃N₄ grains.     

Effects of pressure and temperature on dyeing acrylic fibres with basic dyes in supercritical carbon dioxide

The dyeing of acrylic fibre with CI Basic Blue 47 has been investigated using an ammonium carboxylate perfluoropolyether as an auxiliary in order to perform the reverse micellar system in supercritical carbon dioxide media. The basic dye was satisfactorily solubilised in the interior of the reverse micelle in the system, and dyeability in the supercritical carbon dioxide media was excellent, even in the absence of a retardant and/or an acid. The optimum proton-rich condition for dyeing of acrylic fabric is performed in reverse micelle aggregates and the proton-rich water pool is suitable for dye uptake by the fibre even without the presence of additives. Changes in glass transition temperature of acrylic fibre in the carbon dioxide media also influence the dyeing behaviour of acrylic fabric.     

Pervaporation separation of water/ethanol mixtures through polysaccharide membranes. II. The permselectivity of chitosan membrane

The separation of water/alcohol mixtures through chitosan membrane was investigated. The degree of the deacetylation of chitosan did not affect the selectivity of the membrane in the separation of the water/ethanol mixture. The selectivity of the chitosan membrane was affected by the specific salts such as CoSO₄, ZnSO₄, and MnSO₄ and it increased when the salts were present in the feed mixture or the membrane was pretreated with the salt solution. This behavior would be explained by the contraction of the “holes” produced by the thermal motion of polymer chains and this contraction would be correlated with the conformation change of chitosan molecule due to the formation of complexes with metal ions.     

DIRECT NUMERICAL SIMULATION OF BLUFF BODY FLOWS USING NON-STAGGERED GRIDS

The present authors pointed out in the previous paper [1] that the implicit SMAC scheme is quite efficient and non-staggered grid arrangement can decrease the computational effort and save the storage memory which is very important to the direct numerical simulation (DNS) of complicated 3-D flow fields. But using non-staggered grid arrangement, the pressure field oscillation (PFO) ordinarily occurs and also, the pressure on the solid walls including sharp corners need to be prescribed directly as the pressure boundary conditions.

In this paper, a new interpolation method, which is a modification to Cheng and Armfield's interpolation formulation, is presented in order to completely prevent PFO from occurring, Moreover, a more accurate specification method of wall pressures and special treatment of pressures at sharp corners are proposed. To test the new methods proposed, the DNS of flow past a square cylinder and flows over backward-facing steps, which are typical of the flow fields with sharp corners, is made using the implicit SMAC scheme combined with these methods. The calculated results are compared with the previous experimental and numerical data and show good agreement with them.     

Further Improvement in Mechanical Properties of Highly Anisotropic Silicon Nitride Ceramics

Si₃N₄ceramics were fabricated by tape casting of a raw-powder slurry seeded with three types of rodlike β-Si₃N₄particles. The effects of seed size on the microstructure and mechanical properties of the sintered specimens were investigated. All the seeded and tape-cast silicon nitrides presented an anisotropic microstructure, where the elongated grains grown from seeds were preferentially oriented parallel to the casting direction. The orientation degree of these grains, f ₀, was affected by seed size, and small-seed addition led to the highest f ₀value. This material exhibited high bending strength (∼1.4 GPa) and high fracture toughness (∼12 MPa^.m^1/2) in the direction normal to the grain alignment, which were attributed to the highly anisotropic and fine microstructure.     

Fracture Energy of an Aligned Porous Silicon Nitride

The fracture energy of a porous silicon nitride with aligned fibrous grains was investigated, using a chevron-notched-beam technique. A crack was constrained to propagate normal to the grain alignment. The obtained fracture energy was ∼500 J/m², which was ∼7 times larger than that of a dense silicon nitride with randomly oriented fibrous grains. The large fracture energy was attributable primarily to the sliding resistance associated with interlocking grains.     

Synthesis and Reactions of Organometallic Polymers Containing Titanacyclobutene Units in the Main Chain

A new class of polymers containing titanacyclobutene units in the main chain were prepared by the reaction of organic dihalides (2) with a binuclear titanium propargyl complex (3) generated in situ from bis(pentamethylcyclopentadienyl)titanium chloride (Cp*₂TiCl, 1), SmI₂, and 1,4-bis(3-bromopropynyl)benzene (2a). The dark red colored polymers (4) thus obtained are soluble in organic solvents such as tetrahydrofuran and chloroform, and they are stable at ambient temperature under argon atmosphere. The reaction of the titanium-containing polymers (4) with hydrogen chloride was found to give organic polymers (7) containing unsaturated main chain.     

Alteration of substrate specificity of rat neurolysin from matrix metalloproteinase-2/9-type to -3-type specificity by comprehensive mutation

The substrate specificity of rat brain neurolysin was rapidly modified by semirational mutagenesis coupled with a yeast molecular display system. Neurolysin mainly recognizes substrates with sequential six residues close to the scissile bond in polypeptides, cleaving a peptide bond in the center position of the six residues. To alter the recognition of the P2' amino acid of substrates by neurolysin, six residues of neurolysin, Asp467, Arg470, Glu510, Tyr606, Tyr610 and Tyr611, which might be involved in the formation of the neurolysin S2' subsite, were individually and comprehensively substituted. The protein libraries of mutant neurolysins comprising 120 species were displayed on the yeast cell surface and screening was carried out using two fluorescence-quenching peptides, the matrix metalloproteinase-2/9- (MMPs-2/9-) and MMP-3-specific substrates, which consisted of similar amino acids, except for alanine (for MMPs-2/9) or glutamic acid (for MMP-3) at the P2' amino acid position. Among mutant neurolysins, the Y610L mutant neurolysin exhibited a marked change in substrate specificity. Steady-state kinetic analysis of the purified Y610L mutant neurolysin revealed that the binding efficiency toward the MMP-3-specific substrate was about 3-fold higher than that toward the MMP-2/9-specific substrate. These results indicate that Tyr610 of neurolysin is the important residue to recognize the P2' amino acid of substrates.     

Synthesis and application of fluorescein- and biotin-labeled molecular probes for the chemokine receptor CXCR4

The design, synthesis, and bioevaluation of fluorescence- and biotin-labeled CXCR4 antagonists are described. The modification of D-Lys8 at an epsilon-amino group in the peptide antagonist Ac-TZ14011 derived from polyphemusin II had no significant influence on the potent binding of the peptide to the CXCR4 receptor. The application of the labeled peptides in flow cytometry and confocal microscopy studies demonstrated the selectivity of their binding to the CXCR4 receptor, but not to CXCR7, which was recently reported to be another receptor for stromal cell-derived factor 1 (SDF-1)/CXCL12.