Assessment of trace element levels in Rhododendron honeys of Black Sea Region, Turkey

Rhododendron and multi-flower honeys obtained from Black Sea Region of Turkey (12 Rhododendron and 8 multi-flower honeys) were studied to determine the presence of the 14 trace elements such as Cu, Cd, Pb, Co, Cr, Ni, Al, Se, Zn, Mn, Fe, K, Ca and Mg. Trace element determination was performed by atomic absorption spectrometry (AAS) after microwave digestion. The results revealed that Rhododendron honeys exhibited higher concentrations of Cu, Co, Cr, Ni, Se, Zn, Ca and Mg but lower concentrations of Al, Mn, Fe and K than in the multi-flower honeys. Trace element levels in analyzed honey samples were generally lower than literature values.     

Evaluation of various digestion procedures for trace element contents of some food materials

The levels of trace elements in different types of food material consumed in Turkey were determined by flame and graphite furnace atomic absorption spectrometry. Food samples were digested with dry ashing, wet ashing and microwave digestion procedures in this study. The microwave digestion procedure was chosen for the digestion of all the food samples because it required shorter time and made higher recovery (specially for Se). Fe, Cu, Mn, Zn, Al and Se were determined by flame and graphite furnace atomic absorption spectrometry, respectively. Relative standard deviations (RSD) were found below 10%. The accuracy of the procedure was confirmed by certified reference materials. Moreover, this procedure was easier to use when compared with dry and wet digestions.     

Degradation of 17beta-estradiol and bisphenol A in aqueous medium by using ozone and ozone/UV techniques

Decomposition and complete degradation of two endocrine disrupters, namely 17beta-estradiol (E2) and bisphenol A (BPA) in aqueous medium by using ozone (O3) only and O3/UV advanced oxidation techniques (AOT) has been studied. The efficiency of the O3 systems used were determined based on the initial conversion and complete degradation of the substrates. Within the limits of the O3 dosages used, coupling of UV decreased the O3 consumption by 22.5% in converting the same amount of E2. Also the time to convert the same amount of E2 was considerably decreased. It was observed that there is no significant difference in O3 amount consumed for complete conversion of BPA by O3 and O3/UV systems. However, when O3 dosage decreased the amount of BPA conversion exhibits significant differences between two processes. The intermediate products formed during the oxidation of E2 were determined to be formed by oxidation of aromatic side of E2 with O3/*OH radical.     

Evaluation of counterions for electrospray ionization mass spectral analysis of a highly sulfated carbohydrate,sucrose octasulfate

A systematic approach was used to evaluate the electrospray ionization mass spectral (ESI-MS) analysis of sucrose octasulfate (SOS), an important pharmaceutical agent. SOS represents a model for other suffated carbohydrates, such as heparin and glycosaminoglycan-derived oligosaccharides that also are highly sulfated and pose difficult analytical problems. A survey of ammonium counterions showed that 1 degree, 2 degrees, and 3 degrees ammonium salts of SOS gave substantial fragmentation as a result of sulfate loss. In contrast, quaternary ammonium and phosphonium salts gave excellent ESI spectra, particularly in the positive ion mode. This represents the first report of the ESI-MS analysis of sulfated carbohydrates in the positive ion mode.     

Investigation of the Effects of some Parameters in the Production of Chromate from Chromite Ores in Iskenderun Region

The conversion of chromite ore from iskenderun region into chromate was investigated. Firstly, the chromite ore was analysed using conventional chemical methods. Then, the effect of some parameters such as roasting time, temperature and the amount of additives on the conversion efficiency to the chromate was examined. The optimum roasting conditions were determined as 300°C, 2 hours, 10 times the stoichiometrically required amounts of NaClO₃ and 6 times the stoichiometrically required amounts of KOH. Under these conditions, the maximum recovery of chromate was found to be 100%. The product obtained from the roasting process was leached with water to produce a clean chromate solution. The effect of temperature and solid/liquid (S/L) ratio was investigated in the water leaching experiments. The optimum experimental results obtained were 100% at a 1:5 solid to water ratio at 25°C and 20 min leaching period. The chromate solution was purified using conventional purification processes.     

Effect of Deep Cryogenic Treatment on Wear Resistance of AISI 52100 Bearing Steel

In this study, the effects of deep cryogenic treatment (DCT) on the wear resistance of AISI 52100 bearing steel were investigated. For this purpose, a number of bearing steel samples were held for different times (12, 24, 36, 48, 60 h) at deep cryogenic temperatures (?145 °C). The wear experiments were carried out in a ball–disk arrangement, by applying loads of 10 and 20 N and a sliding velocity of 0.15 m/s. After conducting the experimental studies, 36 h was found to be the optimal holding time. At this holding time, the wear rate and friction coefficient were decreased, while the hardness reached to maximum values. It was observed that DCT led to significant microstructural changes, which resulted in improved tribological properties.     

Kinetics and equilibrium studies for the adsorption of Acid Red 57 from aqueous solutions onto calcined-alunite

The adsorption of Acid Red 57 (AR57) onto calcined-alunite was examined in aqueous solution in a batch system with respect to contact time, pH and temperature. The first-order, pseudo-second-order kinetic and the intraparticle diffusion models were used to describe the kinetic data and the rate constants were evaluated. The experimental data fitted very well the pseudo-second-order kinetic model and also followed the intraparticle diffusion model up to 90 min. The Langmuir and Freundlich adsorption models were applied to describe the equilibrium isotherms and the isotherm constants were also determined. The equilibrium data are successfully fitted to the Langmuir adsorption isotherm. The Langmuir isotherm constant, K(L), was used to evaluate the changes of free energy, enthalpy and entropy of adsorption for the adsorption of AR57 onto calcined-alunite. The results indicate that calcined-alunite could be employed as low-cost material for the removal of acid dyes from textile effluents.     

Investigation of Corrosion Behavior of Borided Gear Steels

In this study, corrosion behaviors of GS18NiMoCr36 (GS 18) and GS32NiCrMo6.4 (GS 32) gear steels borided in Ekabor-II powder at the temperature of 950 °C for 2 and 6 h were investigated in a 6 % M HCI acid solution. The boride layer was characterized by optical microscopy, X-ray diffraction technique and the Micro-Vickers hardness tester. X-ray diffraction analysis of boride layers on the surface of the steels revealed the existence of FeB, Fe₂B, CrB and Cr₂B compounds. The thickness of the boride layer increases by increasing boriding time for gear steels. The hardness of the boride compounds formed on the surface of the steels GS 18 and GS 32 ranged from 1,728 to 1,905 HV_0,05 and 1,815 to 2,034 HV_0,05 respectively, whereas Vickers hardness values of the untreated steels GS 18 and GS 32 were 335 HV_0,05 and 411 HV_0,05, respectively. The corrosion resistance of borided gear steels is higher compared with that of unborided steels. The boride layer increased the corrosion resistances of gear steels 4–6-fold.     

Effect of Sintering Duration on Some Properties of Pure Magnesium

Powder Metallurgy and Metal Ceramics - Tribological and physical properties of pure magnesium (Mg) are investigated during sintering for 2, 4, and 6 h at the temperature of 600°C. The pure...     

Heat transfer enhancement in a tube using circular cross sectional rings separated from wall

A numerical study was undertaken for investigating the heat transfer enhancement in a tube with the circular cross sectional rings. The rings were inserted near the tube wall. Five different spacings between the rings were considered as p = d/2, p = d, p = 3d/2, p = 2d and p = 3d. Uniform heat flux was applied to the external surface of the tube and air was selected as working fluid. Numerical calculations were performed with FLUENT 6.1.22 code, in the range of Reynolds number 4475–43725. The results obtained from a smooth tube were compared with those from the studies in literature in order to validate the numerical method. Consequently, the variation of Nusselt number, friction factor and overall enhancement ratios for the tube with rings were presented and the best overall enhancement of 18% was achieved for Re = 15,600 for which the spacing between the rings is 3d.