Reviewing 25 Years of Testing Technique Experiments

Mature knowledge allows engineering disciplines the achievement of predictable results. Unfortunately, the type of knowledge used in software engineering can be considered to be of a relatively low maturity, and developers are guided by intuition, fashion or market-speak rather than by facts or undisputed statements proper to an engineering discipline. Testing techniques determine different criteria for selecting the test cases that will be used as input to the system under examination, which means that an effective and efficient selection of test cases conditions the success of the tests. The knowledge for selecting testing techniques should come from studies that empirically justify the benefits and application conditions of the different techniques. This paper analyzes the maturity level of the knowledge about testing techniques by examining existing empirical studies about these techniques. We have analyzed their results, and obtained a testing technique knowledge classification based on their factuality and objectivity, according to four parameters.     

Sliding Mode ∑‐Δ Modulation Control of the Boost Converter

A switched implementation of average dynamic output feedback laws trough a ∑‐Δ‐modulator, widely known in the classic communications and analog signal encoding literature, not only frees the sliding mode control approach from state measurements and the corresponding synthesis of sliding surfaces in the plant's state space, but it also allows to effectively transfer all desired closed loop features of an uniformly bounded, continuous, average output feedback controller design into the more restrictive discrete‐valued (ON‐OFF) control framework of a switched system. The proposed approach is here used for the input‐output sliding mode stabilization of the “boost” DC‐to‐DC converter. This is achieved by means of a well known passivity based controller but any other output feedback design would have served our purposes. This emphasizes the flexibility of the proposed sliding mode control design implementation through ∑‐Δ‐modulators.     

Enhanced liquid biofuel production from crude palm oil over synthesized NiMoW-ZSM-5/MCM-41 catalyst

Micro-mesoporous ZSM-5/MCM-41 composites were prepared and then loaded with varied contents of NiMoW by the wet impregnation method. The hydrocracking conversion of crude palm oil to liquid biofuels with the prepared catalysts was carried out in a batch reactor at 400°C for 2 h. ZSM-5/MCM-41 composite exhibited 51.00% conversion with a yield of 9.23% gasoline, 20.60% kerosene, and 21.17% diesel. Upon loading of NiMoW, the catalysts exhibited an improved conversion (≥ 62.60%) and a reduced formation of coke, which resulted from combined properties of ZSM-5 with MCM-41 and the presence of dispersed NiMoW. The contents of impregnated metals also affected the performance of catalysts. Using ANOVA analysis (p < 0.05), we found that 8:8:8 wt.% NiMoW-ZSM-5/MCM-41 catalyst was suitable for the production of biofuels, when considering the efficiency and cost-effectiveness.     

Flow pattern and heat transfer characteristics of R-134a refrigerant during flow boiling in a horizontal circular mini-channel

Flow boiling heat transfer of R-134a refrigerant in a circular mini-channel, 600 mm long with a diameter of 1.75 mm, is investigated experimentally in this study. The test section is a stainless steel tube placed horizontally. Flow pattern and heat transfer coefficient data are obtained for a mass flux range of 200–1000 kg/m² s, a heat flux range of 1–83 kW/m² and saturation pressures of 8, 10, and 13 bar. Five different flow patterns including slug flow, throat-annular flow, churn flow, annular flow and annular-rivulet flow are observed and the heat transfer coefficient data for different flow patterns are presented. The heat transfer coefficient increases with increasing heat flux but is mostly independent of mass flux and vapour quality. In addition, it is indicated from the experiments that the higher the saturation pressure, the lower is the heat transfer coefficient. Comparisons of the present data with the existing correlations are also presented.     

Increasing validity through replication: an illustrative TDD case

Software Quality Journal - Software engineering (SE) experiments suffer from threats to validity that may impact their results. Replication allows researchers building on top of previous...     

An inspection of viscosity model for homogeneous two-phase flow pressure drop prediction in a horizontal circular micro-channel

This study analyzes several well-known two-phase viscosity models in order to address the appropriate correlations among them for application to micro-channel. Pressure drop data is obtained from adiabatic two-phase air–water flow experiments. A fused silica channel, 320 mm long, with an inside diameter of 0.53 mm is used as the test section. The measured data is compared with the homogeneous flow predictions calculated using the existing viscosity models and detailed comparisons are discussed.     

Two-phase air-water flow in micro-channels: An investigation of the viscosity models for pressure drop prediction

Adiabatic two-phase air-water flow is experimentally studied in this work. Two channels, made of fused silica, with different diameters of 0.53 and 0.15 mm are used as test sections. The void fraction data for both tubes are obtained by image analysis. For the larger channel, the void fraction is found to be a linear relationship with the volumetric quality. In the case of the smaller one, however, the non-linear void fraction is obtained. The measured frictional pressure drop data are compared with the predictions regarding the homogeneous flow assumption. Several well-known two-phase viscosity models are subsequently evaluated for applicability to micro-channels.     

Utilization of rice-husk packed beds as fine dust collectors at heavy dust loadings

Typical rice mills generally generate tonnes of biomass which is rice husks and a significant quantity of coarse and fine dusts from the paddy, resulting in public health concern. Instead of normal air cyclones which are not efficient for collecting fine soft-hair (detached pubescence) particles smaller than a few microns, a new system using packed beds of rice husks was developed for collection fine dusts. It was found that the rice-husk packed beds could exhibit an effective performance in capturing fine dusts at various dust loadings with collection efficiency higher than 85% by mass. The filtrating phenomenon could be observed as an integrated effect of cake and deep-bed filtrations due to the heavy dust loads, agglomeration of dusts, and cohesion between the dusts and bed of irregularly shaped rice husks. Both the pressure drop across the bed and the overall filtration efficiency remarkably increased at the initial clean stage, then increased more slowly due to the recurrent fracture of the dust cake layer.