Since solid, non-metallic inclusions influence considerably the quality of casted steel products, carbon-bonded alumina foam filters are used in secondary metallurgical treatments to remove these particles from steel melts. In order to attain a significant improvement of the filtration process, five different carbonaceous spinel compounds from the Fe-/Mg-/Mn-Al-O systems are applied on carbon-bonded alumina filters in this study and investigated with regard of their filtration efficiency. However, these spinel compounds decompose partially during sintering at 1400?°C under reducing atmosphere, wherefore the resulting coatings contain not only spinel compounds, but also oxidic and metallic components. The subsequent interaction with molten steel leads to the development of multicrystal structures on the filter surface, which stem from interfacial reactions between coating materials, molten steel, and inclusions. As a result of this procedure, a reduction of almost 60% alumina inclusions is measured with the aid of an automatic SEM, whereby spinel compounds from the Fe-Mn-Al-O system achieve highest filtration efficiencies. 相似文献
The determination of elastic properties at application temperature is fundamental for the design of fibre reinforced ceramic composite components. An attractive method to characterize the flexural modulus at room and high temperature under specific atmosphere is the nondestructive Resonant Frequency Damping Analysis (RFDA). The objective of this paper was to evaluate and validate the modulus measurement via RFDA for orthotropic C/C-SiC composites at the application temperature. At room temperature flexural moduli of C/C-SiC with 0/90° reinforcement were measured under quasi-static 4-point bending loads and compared with dynamic moduli measured via RFDA longitudinally to fibre direction. The dynamic modulus of C/C-SiC was then measured via RFDA up to 1250°C under flowing inert gas and showed an increase with temperature which fitted with literature values. The measured fundamental frequencies were finally compared to those resulting from numerical modal analyses. Dynamic and quasi-static flexural moduli are comparable and the numerical analyses proved that bending modes are correctly modeled by means of dynamic modulus measured via RFDA. The nondestructive RFDA as well as the numerical modeling approach are suitable for evaluation of C/C-SiC and may be transferred to other fibre reinforced ceramic composite materials. 相似文献
Software and Systems Modeling - Cyber-physical systems reconfigure the structure of their software architecture, e.g., to avoid hazardous situations and to optimize operational conditions like... 相似文献
This paper focuses on the stochastic response of concrete bridges considering uncertainty in bearing and abutment stiffness. A multi-span simply supported bridge with concrete girders is selected. A 3D-dimensional model is prepared, and nonlinear response history analyses are performed. For the numerical dynamic simulation, the non-sampling stochastic method based on generalized polynomial chaos (gPC) expansion is utilised. The uncertain parameters include the vertical and shear stiffness of bearings and the lateral stiffness of abutments are presented by the truncated gPC expansions. Furthermore, the system response such as base shear, acceleration, velocity and displacement in different columns is presented by gPC expansion with unknown deterministic coefficients. The stochastic Galerkin projection is employed to calculate a set of deterministic equations. A non-intrusive solution, as a set of collocation points, determines the unknown gPC coefficients of the system response and the results are compared with Monte Carlo simulations. The key advantage of spectral discretization is the combination of the mentioned method with the spatial discretization, e.g. finite element model. This study also emphasises the accuracy in results and time efficiency of the proposed non-sampling method for uncertainty quantification of stochastic systems comparing to sampling procedure (e.g. Monte Carlo simulation). 相似文献
A conventional membrane-type stainless steel shock tube has been coupled to a high-repetition-rate time-of-flight mass spectrometer (HRR-TOF-MS) to be used to study complex reaction systems such as the formation of pollutants in combustion processes or formation of nanoparticles from metal containing organic compounds. Opposed to other TOF-MS shock tubes, our instrument is equipped with a modular sampling unit that allows to sample with or without a skimmer. The skimmer unit can be mounted or removed in less than 10 min. Thus, it is possible to adjust the sampling procedure, namely, the mass flux into the ionization chamber of the HRR-TOF-MS, to the experimental situation imposed by species-specific ionization cross sections and vapor pressures. The whole sampling section was optimized with respect to a minimal distance between the nozzle tip inside the shock tube and the ion source inside the TOF-MS. The design of the apparatus is presented and the influence of the skimmer on the measured spectra is demonstrated by comparing data from both operation modes for conditions typical for chemical kinetics experiments. The well-studied thermal decomposition of acetylene has been used as a test system to validate the new setup against kinetics mechanisms reported in literature. 相似文献
A central reaction in homologous recombination is synapsis, which involves invasion of duplex DNA by a homologous single strand. A key intermediate in this process is the presynaptic filament, a protein-DNA complex composed of a "strand transferase" polymerized along the invading single strand. In this report, the organization and mechanism of assembly of the bacteriophage T4 presynaptic filament are explored. Three T4 proteins, encoded by the uvsX, uvsY and 32 genes, are involved in this process. It is demonstrated that a well-defined series of events involving multiple protein-DNA and protein-protein interactions is required to mediate a transition from an initial gene 32-DNA complex to a mature presynaptic filament in which the UvsX and UvsY proteins are in contact with the DNA and each other, while most or all of the gene 32 protein is removed from the complex. 相似文献
We present an approach for the visualization and interactive analysis of dynamic graphs that contain a large number of time steps. A specific focus is put on the support of analyzing temporal aspects in the data. Central to our approach is a static, volumetric representation of the dynamic graph based on the concept of space-time cubes that we create by stacking the adjacency matrices of all time steps. The use of GPU-accelerated volume rendering techniques allows us to render this representation interactively. We identified four classes of analytics methods as being important for the analysis of large and complex graph data, which we discuss in detail: data views, aggregation and filtering, comparison, and evolution provenance. Implementations of the respective methods are presented in an integrated application, enabling interactive exploration and analysis of large graphs. We demonstrate the applicability, usefulness, and scalability of our approach by presenting two examples for analyzing dynamic graphs. Furthermore, we let visualization experts evaluate our analytics approach.
Myosin family motors play diverse cellular roles. Precise insights into how the light chains contribute to the functional variabilities among myosin motors, however, remain unresolved. Here, it is demonstrated that the fast skeletal muscle myosin II isoform myosin heavy chain (MHC‐IID) can be transformed into a processive motor, by simply replacing the native regulatory light chain MLC2f with the regulatory light chain variant MLC2v from the slow muscle myosin II. Single molecule kinetic analyses and optical trapping measurements of the hybrid motor reveal marked changes such as increased association rate of myosin toward adenosine triphosphate (ATP) and actin by more than twofold. The direct consequence of high adenosine diphosphate (ADP) affinity and increased actin rebinding is the altered overall actomyosin association time during the cross‐bridge cycle. The data indicate that the MLC2v influences the duty ratio in the hybrid motor, suggestive of promoting interhead communication and enabling processive movement. This finding establishes that the regulatory light chain fine‐tunes the motor's mechanical output that may have important implications under physiological conditions. Furthermore, the success of this approach paves the way to engineer motors from a known motor protein element to assemble highly specialized biohybrid machines for potential applications in nano‐biomedicine and engineering. 相似文献