Equal-channel angular extrusion of beryllium

The equal-channel angular extrusion (ECAE) technique has been applied to a powder metallurgy (P/M) source Be alloy. Extrusions have been successfully completed on Ni-canned billets of Be at approximately 425°C. No cracking was observed in the billets, and significant grain refinement was achieved. In this article, microstructural features and dislocation structures are discussed for a singlepass extrusion, including evidence of <c> and <c+a> dislocations. Significant crystallographic texture developed during ECAE, which is discussed in terms of this unique deformation processing technique and the underlying physical processes which sustain the deformation. S.R. AGNEW, formerly with the Oak Ridge National Laboratory, Oak Ridge, TN 37831-6115 This article is based on a presentation made in the symposium entitled “Defect Properties and Mechanical Behavior of HCP Metals and Alloys” at the TMS Annual Meeting, February 11–15, 2001, in New Orleans, Louisiana, under the auspices of the following ASM committees: Materials Science Critical Technology Sector, Structural Materials Division, Electronic, Magnetic & Photonic Materials Division, Chemistry & Physics of Materials Committee, Joint Nuclear Materials Committee, and Titanium Committee.     

Grid-friendly connecting of constant-speed wind turbines using external resistors

In this paper, an alternative method of connecting fixed-speed wind turbines, with active pitch mechanisms or variable-slip generators, is proposed and evaluated. Instead of using the conventional soft starter, external resistors are used. The method was evaluated via laboratory tests on a 15-kW machine and theoretically on a 1-MW wind turbine. The proposed method causes smaller grid power quality impact, especially on inductive grids, compared with soft starters. This means that it will be possible to install constant-speed wind turbines to weaker grids using this method.     

Large Coulomb blockade oscillations at room temperature in ultranarrow wire channel MOSFETs formed by slight oxidation process

We propose a new fabrication technique of room-temperature operating silicon single-electron transistors (SETs). The devices are in the form of ultranarrow wire channel MOSFETs, where a sub-10-nm channel is formed by wet etching and slight thermal oxidation. Large Coulomb blockade (CB) oscillations whose peak-to-valley current ratio at room temperature is as high as 6.8 are observed in the fabricated ultranarrow wire channel MOSFETs. It is found that larger CB oscillations are obtained in the ultranarrow wire channel SETs than in the point-contact channel SETs. It is considered that the potential fluctuations induced during the channel formation processes give rise to multiple-dot SET structures in the ultranarrow wire channel MOSFETs.     

Implementation of a self-timed segmented bus

We propose an asynchronous structure for implementation on a SoC. An intersegment topological arrangement preserves parallelization and, through a so-called central arbiter, efficiently organizes communication with high signaling speed in the proposed structure. Researchers proposed the concept of segmenting buses primarily for multicomputer architectures. More recent approaches address on-chip implementation of segmented buses. We present an asynchronous segmented-bus architecture targeted for the modular design of high-performance SoC applications. The structure not only enables faster operation than a conventional bus system but also offers lower power consumption per transferred data item. This is possible because segmentation is realized in such a way that the majority of data transfers in the system are intrasegment transactions on relatively short wires with low or moderate capacitive loads.     

FATIGUE DAMAGE IN 1045 STEEL UNDER VARIABLE AMPLITUDE BIAXIAL LOADING

Abstract— During constant amplitude loading, two different types of crack systems have been reported In the high cycle fatigue (HCF) region, cracks nucleate on a small number of maxium shear strain amplitude planes One of these cracks becomes a dominant crack and leads to failure of the specimen In the low cycle fatigue (LCF) region, equally developed microcracks are observed over the entire gage section and grow during the majority of the life. The failure is due to a linking in which the microcracks join up during the last few cycles of the fatigue life.
To investigate the interaction of these two types of crack systems in biaxial fatigue, experiments were performed on thin-wall tubular specimens in tension, torsion and combined tension-torsion loading The test program included step loading and block loading in which two equivalent strain amplitudes were employed. One of the equivalent strain amplitudes is in the HCF region and the other was in the LCF region
Fatigue lives were predicted from constant amplitude damage curves when a single crack system dominated the fatigue process Two competitive crack systems were sometimes developed on the maximum shear strain amplitude planes in a single specimen under block loading This resulted in a conservative prediction of the fatigue life.     

A Distributed State Estimator Utilizing Synchronized Phasor Measurements

With the creation of balancing authorities by the North American Reliability Council that span large portions of the North American interconnection, and stringent requirements for real time monitoring of power system evolution, faster and more accurate state estimation algorithms that can efficiently handle systems of very large sizes are needed in the present environment. This paper presents a distributed state estimation algorithm suitable for large-scale power systems. Synchronized phasor measurements are applied to aggregate the voltage phase angles of each decomposed subsystem in the distributed state estimation solution. The aggregated state estimation solution is obtained from the distributed solution using a sensitivity analysis based update at chosen boundary buses. Placement of synchronized phasor measurements in the decomposed subsystems is also investigated in this paper. Test results on the IEEE 118-bus test bed are provided     

The hot blow forming of AZ31 Mg sheet: Formability assessment and application development

The hot blow forming of magnesium sheet offers significant opportunity for forming complex, lightweight parts for automotive applications. This paper characterizes the elevated-temperature formability of AZ31 magnesium sheet materials and the effect of processing conditions on the performance of these materials. In addition, magnesium sheet application development at General Motors Corporation is reviewed.     

Study of thermal effects and self-heating phenomena in planar power SOI MOS transistors

Heat removal problems, thermal effects, and self-heating phenomena occurring during operation of planar power SOI MOS transistors are considered. Using device-technological simulating methods, the transistor characteristics and safe operation range were studied. It was shown that limitations of the safe operation range are mostly associated with structure self-heating rather than with the parasitic bipolar transistor.     

Robust Distributed Source Coding

We consider a distributed source coding system in which several observations must be encoded separately and communicated to the decoder by using limited transmission rate. We introduce a robust distributed coding scheme which flexibly trades off between system robustness and compression efficiency. The optimality of this coding scheme is proved for various special cases.