Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

Some experimental findings in compression-after-impact (CAI) tests of CF/PEEK (APC-2) and conventional CF/epoxy flat plates

Compression-after-impact (CAI) tests have been conducted for quasi-isotropic thick plates with 48 plies by using the NASA method and on plates with 32 plies by using the SACMA method. Specimens are made of CF/PEEK (APC-2) and conventional CF/epoxy for the NASA plates and CF/epoxy for the SACMA plates. In the NASA CAI tests, the sequence of delamination buckling and its propagation is clearly revealed through various experimental techniques. One major technique is moiré topography, and the other is thermo-mechanical stress analysis with a high-accuracy infrared sensor. The arrest of delamination propagation just before catastrophic failure due to high fracture toughness is clearly captured by the moiré camera. This behavior provides good CAI values of CF/PEEK. The initial buckling properties of the delaminated region by the impact are then extensively discussed. Numerical predictions of initial buckling stress have been obtained by modelled geometry of the delaminated region simplified from its precise structure clarified by ultrasonic C-scanning. They agree fairly well with the experimental results. The in-plane stress distribution in the delaminated region before initial buckling is measured by an infrared stress graphic system. This compared favorably with finite element predictions. Two types of symmetric buckling modes with respect to the central plate surface, twin and single peak ones, are experimentally captured.     

The cause of the uneven carbonization process in wet coal charging in coke oven chamber

In the case of the wet coal charging process in coke oven chamber, it is known that the coking process is uneven and a local carbonization delay occurs. The reason was investigated through a laboratory-scale experiment and a quantitative estimation. A partial carbonization test in a test coke oven replicated the uneven plastic layer and local carbonization delay. It was revealed that most of the gas generated in the uncarbonized coal layer results from the evaporation of condensed water and that steam can break through the plastic layer in a test coke oven. Moreover, the order estimation implied that steam that generates in the uncarbonized coal layer and breaks through the plastic layer has sufficient heat capacity to cool the heating wall and delay the carbonization. It was also shown that the steam pressure peak measured in a commercial coke oven is much lower than the estimated steam pressure in this study assuming steam not breaking through the plastic layer. The above-mentioned results and quantitative investigation strongly support the ‘steam breaking through the plastic layer’ theory proposed by Dr. Rohde that an uneven carbonization process is caused by vaporized coal moisture breaking through the plastic layer at definite, unforeseeable points, which results in cooling of the wall by the steam flow.     

NiCoFe/C cathode electrocatalysts for direct ethanol fuel cells

A direct ethanol fuel cell (DEFC), which is less prone to ethanol crossover, is reported. The cell consists of PtRu/C catalyst as the anode, Nafion^® 117 membrane, and Ni–Co–Fe (NCF) composite catalyst as the cathode. The NCF catalyst was synthesized by mixing Ni, Co, and Fe complexes into a polymer matrix (melamine-formaldehyde resins), followed by heating the mixture at 800 °C under inert atmosphere. TEM and EDX experiments suggest that the NCF catalyst has alloy structures of Ni, Co and Fe. The catalytic activity of the NCF catalyst for the oxygen reduction reaction (ORR) was compared with that of commercially available Pt/C (CAP) catalyst at different ethanol concentrations. The decrease in open circuit voltage (V_oc) of the DEFC equipped with the NCF catalysts was less than that of CAP catalyst at higher ethanol concentrations. The NCF catalyst was less prone to ethanol oxidation at cathode even when ethanol crossover occurred through the Nafion^®117 film, which prevents voltage drop at the cathode. However, the CAP catalyst did oxidize ethanol at the cathode and caused a decrease in voltage at higher ethanol concentrations.     

Temperature Profile of Anatase-TiO2Powder Compact during Microwave Heating

Anatase-TiO₂ cylindrical pellets were microwave sintered and partially transformed to rutile-TiO₂.The rutile concentration profile was determined as a function of location within the pellet. The rutile distribution in the microwavesintered pellets was different from that in pellets sintered by conventional fast firing. Temperature profiles within the pellets were estimated using the irreversible nature of the anatase-rutile transformation. The estimated temperature profile within each pellet was not uniform. In the axial direction, maximum temperature occurred in the middle of the pellet. In the radial direction, maximum temperature occurred at 1 mm below the surface of the cylinder wall. Analysis of the temperature profile indicated that, although heat flow occurred in the microwave-sintered pellet, the temperature profile did not change during a microwave exposure of 5–90 min.     

Breed differences in the histochemical properties of the M. pubo-ischio-femoralis pars medialis myofibre of domestic cocks

1. Histochemical properties of M. pubo-ischio-femoralis pars medialis (PIF muscle) were compared in 7 breeds of cocks. This muscle was largely composed of Type I fibres and their transitional form (Type I tr). Type IIA fibres were observed in the cranial part. 2. The weight and cross-sectional area of the PIF muscle increased with increasing body weight. However, the relative muscle development to body weight differed among the 7 breeds. 3. A quarter of Type I fibres were of the transitional variety in bantam fowls. Conversely, few, if any, Type I tr fibres were observed in the large breeds where the muscle was poorly developed. 4. As the histochemical properties of Type I fibres made an effective response to the different body weights and the relative PIF muscle development among breeds, it was concluded that PIF muscle performed an important function in supporting the body weight and maintaining posture.     

Permeation and separation of organic liquid mixtures through liquid-crystalline polymer networks

A side-chain liquid-crystalline polymer (LCP) was synthesized by the addition of the mesogenic monomer to poly(methyl siloxane) in presence of a Pt-catalyst. When an aqueous solution of 10wt% ethanol was permeated through a LCP membrane by pervaporation at various temperatures, the permeation rate increased with increasing temperature and drastically changed at glass-nematic (Tg) and nematic-isotropic (TNI) transition temperatures of the LCP membrane. The LCP membrane exhibited the waterpermselectivity in the glassy and liquid-crystalline states. The ethanol concentration in the permeate increased with increasing permeation temperature and the LCP membrane changed from the waterpermselectivity to the ethanol-permselectivity around TNI. These results suggested that the permselectivity was influenced by the change of the LCP membrane structure, that is, its state transformation. It was found that a balance of the orientation of mesogenic groups and flexibility of siloxane chains is very important for the permeability and selectivity.     

Ulcerative colitis associated with Weber-Christian panniculitis and musculitis: a case report

A case of 22-year-old man suffering from ulcerative colitis, in whom Weber-Christian panniculitis and musculitis occurred simultaneously, is reported. He had suffered from ulcerative colitis for 7 years and he again had bloody stools 1 month before being admitted. Two weeks before admission, large (2-4 cm) subcutaneous tumors appeared. Weber-Christian panniculitis, musculitis, and active stage ulcerative colitis were diagnosed. All the symptoms went into remission after steroid therapy. The possibility of the existence of a common antigen in enterobacterial wall, colonic epithelium, and adipose tissue was suggested.