Shear rate dependence of viscosity and first normal stress difference of LCP/PET blends at solid and molten states of LCP

The liquid crystalline polymer (LCP) and polyethylene terephthalate (PET) were blended in an elastic melt extruder to make samples having 20, 40, 60, 80, and 100 wt % of LCP. Morphology of these samples was studied using scanning electron microscopy. The steady state shear viscosity (η), dynamic complex viscosity (η*) and first normal stress difference (N₁) were evaluated and compared at two temperatures: 265°C, at which LCP was in solid state, and 285°C, at which LCP was in molten state. The PET was in molten state at both the temperatures. The shear viscosity of the studied blends displayed its dependence on composition and shear rate. A maxima was observed in viscosity versus composition plot corresponding to 80/20 LCP/PET blend. The N₁ increased with LCP loading in PET and with the increased asymmetry of LCP droplets. The N₁ also varied with the shear stress in two stages; the first stage demonstrated elastic deformation, whereas second stage displayed dominant plastic deformation of LCP droplets. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2212–2218, 2007     

Effects of preparation conditions on the surface modification and performance of polyethersulfone ultrafiltration membranes

The impact that some membrane preparation steps had on ultrafiltration (UF) membrane characteristics and performance was studied. Polyethersulfone (PES) was employed as base polymer, while N‐methyl pyrrolidone (NMP) was used as a solvent, and polyvinylpyrrolidone (PVP) was used as a nonsolvent pore‐forming additive. The manufacturing variables studied were solvent evaporation time and membrane surface modification, using a fluorine‐based copolymer referred to as surface‐modifying macromolecule (SMM). The flat sheet membranes, prepared via phase inversion, were characterized using solute transport data, X‐ray photoelectron spectroscopy (XPS), and contact angle measurements. Membrane performance was evaluated via filtration test protocol that included a 6‐day filtration of concentrated river water. The flux reduction with time was modeled using single and dual mechanisms of fouling. The pore blockage/cake filtration model described better the behavior of the permeation rate along the experiments. Increasing the solvent evaporation time decreased the size of the pores and the permeation rate. However, it did not significantly affect the removal of the organic compounds naturally present in the river water used as feed. XPS and contact angle measurements proved that the short evaporation periods did not allow enough SMM migration to the surface to provoke a significant effect on the membrane performance. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

EFFECT OF NONSOLVENT ADDITIVES ON THE PORE SIZE AND THE PORE SIZE DISTRIBUTION OF AROMATIC POLYAMIDE RO MEMBRANES

In this paper discussions are made on the effect of nonsolvent swelling agents on the average pore size and pore size distributions at the surface of polyamide membranes which result from casting solutions involving above nonsolvent swelling agents.

The size of the polymer aggregate in the film casting solution and the size of polymer network pores are correlated to physicochemical data of ions which constitute the electrolytes used as nonsolvent swelling agents. As such ionic properties the charge density and the free energy of transition of ions from polyamide phase to water phase were considered. The validity of the correlation is limited in a range of casting solution composition where the polymer concentration in the casting solution is close to the limiting concentration of polymer at the phase boundary and the molar ratio of the nonsolvent swelling agent to the amide group involved in the polyamide polymer is equal to or slightly more than 0.7.     

Deposition of dense isotropic carbon from acetylene in fluidized bed

Pyrolytic carbon was deposited from acetylene in a fluidized bed at 1100°C on alumina microspheres. In case when only argon was used as the diluent gas, density and BAF of the deposit decreased and deposition yield increased with increasing acetylene concentration. Hydrogen sypply suppressed carbon formation and, consequently, caused an increase in density and Lc. BAF was relatively independent of hydrogen concentration. It was found that high density, isotropic carbon can be deposited from acetylene at 1100°C, if an appropriate proportion of hydrogen is added.     

Structural study of hexane-soluble products from hydroliquefaction of three Yallourn brown coal lithotypes over molten salt catalysts

The hexane-soluble fractions of hydroliquefied products from three Yallourn brown coal lithotypes have been separated into five fractions by combined silica-alumina packed column chromatography. Analyses of various fractions by g.c.-m.s. permitted the identification of ≈50 components in the saturate fraction and 40 components in the diaromatic fraction, together with 30 components in the monoaromatics. The components identified were quite similar among hexane-soluble portions of all three lithotypes. A marked predominance of even carbon number alkane (C₂₃-C₂₉) was observed in the hydrocarbon fractions from pale lithotype over $\text{ZnCl}{}_2\text{KCl}$, and medium light lithotype over both pure ZnCl₂ and $\text{ZnCl}{}_2\text{KCl}$. However, medium dark lithotype over both melt catalysts produced a saturate fraction with an odd carbon number(C₂₂-C₂₈) preference. Based on spectral methods, Soxhlet extracts obtained from untreated lithotypes (hexane and benzene solubles) were characterized as complex mixtures of higher molecular weight(300–1000) aliphatic hydrocarbons, which were supposed to be a precursor of the saturates produced from the corresponding lithotype in the catalytic hydroliquefaction.     

Change of the amorphous state by heat treatment below the glass transition temperature

This study was undertaken to elucidate the state of a polymer in the amorphous state through a change of motion of the molecular chain caused by heat treatment below the glass transition temperature. From dielectric measurements of amorphous poly(ethylene terephthalate) heat-treated below T_g, it was found that the average relaxation time, the distribution of relaxation time and the dielectric strength increase with increase of heat treatment. From these results, it was concluded that the amorphous state becomes more random by heat treatment.     

Studies of tetrazoles as rubber chemicals. II. Reactivities and antioxidation activities of reactive antioxidants based on tetrazoles

The chemical reactivities of novel reactive antioxidants based on tetrazoles for carbon–carbon double bonds of liquid polybutadiene and their antioxidation activities toward isoprene rubber were evaluated. These antioxidants, i.e., 2-substituted phenyl-5-(3′,5′ -di-tert-butyl-4′-hydroxyphenyl)tetrazoles (PHPT), were pyrolyzed in liquid polybutadiene at 160–170°C for 30 min to attach to rubber in extents of 61–85% of the nitrileimines formed from PHPT by 1,3-dipolar addition reaction. The reactivities of PHPT followed the order p-Cl > m-Cl > H > p-CH₃ > m-CH₃, p-OC₂H₅, suggesting that PHPT reacts with diene rubber in electrophilic reaction and p-derivatives exhibit higher contents of binding than m-derivatives due to steric hindrance. From oxygen absorption data, the antioxidation activities of PHPT for isoprene rubber vulcanizates followed the order m-Cl, m-CH₃ > H, p-Cl, p-Cl, p-CH₃ > p-OC₂H₅. Isoprene rubber vulcanizates, obtained after pretreatment with PHPT by heating, were extracted with acetone, followed by aging to show that there was good retention and appreciable antioxidation activities of PHPT, especially, p-CH₃ and p-Cl substituted PHPT.     

Anodic Dissolution of Uranium Mononitride in Lithium Chloride-Potassium Chloride Eutectic Melt

Uranium-plutonium nitride is a candidate fuel for fast reactors, but its major drawback is ¹⁴C formation from natural nitrogen. One would probably have to use highly ¹⁵N-enriched nitrogen. A pyrochemical process with molten-salt electroreflning has been proposed as a means to increase the nuclear proliferation resistance of the fuel cycle. Molten-salt electroreflning could also be applied to nitride fuels to make possible the recycling of ¹⁵N. The anodic dissolution behavior of UN in LiCI-KCI melt was studied to provide the basis for a feasibility study of electroreflning of irradiated nitride fuels.     

Cationic copolymerization behavior of a bicyclic orthoester having hydroxy group with glycidyl phenyl ether and volume change on their copolymerization

This article describes cationic ring‐opening copolymerization of a bicyclic orthoester having hydroxy group (BOE‐OH) and glycidyl phenyl ether (GPE), and the volume shrinkage behavior during the copolymerization. THF soluble polyethers [poly(BOE‐OH‐co‐GPE)] were obtained by the copolymerizations at 80–180°C, while crosslinked poly(BOE‐OH‐co‐GPE) was obtained by the copolymerizations at 220–250°C. This crosslinking reaction may originate from the dehydration of methylol groups in the side chain of poly(BOE‐OH‐co‐GPE). The volume shrinkage during the cationic copolymerization reduced as the increase of the BOE‐OH feed ratio. By contrast, the volume shrinkage on the crosslinking polymerization was almost independent on the BOE‐OH feed ratio. Poly(BOE‐OH‐co‐GPE)s with higher BOE‐OH composition showed lower thermal weight loss temperature owing to the release of H₂O by dehydration of methylol groups. The BOE‐OH component in the THF soluble poly(BOE‐OH‐co‐GPE)s lowered the glass transition temperature (T_g), while that in the crosslinked poly(BOE‐OH‐co‐GPE) increased the T_g probably because of the higher crosslinking density. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1356–1361, 2006     

Synthesis of poly(tetrahydrofuran-b-ε-caprolactone) macromonomer via the Sml2-induced transformation

Summary A novel well-defined macromonomer consisting of different types of monomers in polymerization mechanisms was synthesized for the first time through the SmI₂-induced transformation. The macromonomer, -methacryloylpoly-(tetrahydrofuran-b--caprolactone), was prepared by the reaction of methacryloyl chloride with living poly(tetrahydrofuran-b--caprolactone) [poly(THF-b-CL)] which was obtained by the two-electron reduction of the cationic growing center of poly(THF) by samarium iodide (SmI₂) followed by the polymerization of CL. ¹H NMR analysis indicated the quantitative introduction of the methacryloyl group onto the polymer end. The molecular weight distribution of the macromonomer was relatively narrow, and the unit ratio of THF to CL could be controlled by both polymerization time of THF and the amount of CL, resulting from the living nature of both CL- and THF-polymerizations. Radical copolymerization of the produced macromonomers with methyl methacrylate in the presence of AIBN resulted in a polymethacrylate backbone grafted with poly(THF-b-CL) block copolymers.