Radiation-induced polymerization of ethylene in pilot plant. III. Heavy-phase recycling process

Radiation-induced polymerization of ethylene using aqueous tert-butyl alcohol as medium was carried out in a large-scale pilot plant with a 50-liter central source-type reactor at a pressure of 105 to 395 kg/cm², temperature of 30° to 80°C, mean dose rate of 4.5 × 10⁴ to 1.9 × 10⁵ rads/hr, ethylene feed rate of 5.5 to 23.5 kg/hr, and medium feed rate of 21 to 102 l./hr. The space–time yield and molecular weight of the polymer were in the range of 4.7 to 16.8 g/l.-hr and 1.3 × 10⁴ to 8.9 × 10⁴, respectively. The space–time yield and molecular weight increased with mean residence time at 30°C, whereas at 80°C they became almost independent of the time. The space–time yield increased with pressure and dose rate, slightly decreased with temperature, and was maximum at ethylene molar fraction of 0.5. The polymer molecular weight increased with pressure and ethylene molar fraction, and decreased with dose rate and temperature. The total amount of deposited polymer on the reactor wall, source case wall, and scraping blades was usually less than 1 kg, which was negligibly small for the analysis of polymerization. Continuous discharge of the polymer slurry and production of fine-powder polyethylene were successfully carried out. In the central source-type reactor, a dose rate of 1.9 × 10⁵ rads/hr was obtained with a ⁶⁰Co source of ca. 12 kCi.     

Control of molecular weight distribution of isotactic polypropylene obtained by a MgCl2-supported TiCl4 catalyst

It is of great importance in propene polymerization to control molecular weight and molecular weight distribution as well as isotacticity. Propene polymerization was carried out with an isospecific MgCl₂/TiCl₄-Cp₂TiMe₂ catalyst in the presence of various kinds of external Lewis bases. It was found that the molecular weight distribution of the isotactic polymer could be controlled while retaining high activity, high isospecificity and high molecular weight only by changing the kind and/or amount of the Lewis bases. © 1997 Elsevier Science Ltd.     

Polymeric phosphonium salts as a novel class of cationic biocides. VII. Synthesis and antibacterial activity of polymeric phosphonium salts and their model compounds containing long alkyl chains

Various polymeric phosphonium salts containing long alkyl chains (C₁₀? C₁₈) and their corresponding model compounds were prepared, which possess the same hydrophobic structure as that of the common disinfectants (quaternary ammonium salts), and their antibacterial activities were evaluated by means of the viable cell counting method against Staphylococcus aureus (Gram-positive) and Escherichia coli (Gram-negative). The polymer with the decyl group exhibited a higher activity than that of the corresponding model compound, particularly against the Gram-positive strain. Furthermore, antibacterial activity of the polymers was found to decrease as the chain length increased. In contrast with the polymers, the antibacterial activity of the corresponding model compounds increased as hydrophobicity of the substituents increased. The antibacterial activity was strongly dependent on the structure, particularly on the length of the alkyl chain. © 1994 John Wiley & Sons, Inc.     

A model for the complex permittivity of water at frequencies below 1 THz

Experimental permittivity data of liquid water, compiled from the open literature, were selectively applied to support a modeling strategy. Frequencies up to 1 THz and atmospheric temperatures are covered with an expression made up by two relaxation (Debye) terms. The double-Debye model reduces to one term when the high frequency limit is set at 100 GHz, and the model can be extended to 30 THz by adding two resonance (Lorentzian) terms. The scheme was carried out by employing nonlinear least-squares fitting routines to data we considered reliable.     

Spatial distribution of silica fillers in phase-separated rubber blends investigated by three-dimensional elemental mapping

The distribution of nano-sized silica in binary rubber blends is characterized by scanning transmission electron microscopy (STEM) tomography combined with energy dispersive X-ray spectrometry (EDX). 3D distribution of silica is visualized by STEM-EDX tomography with the tilt-series of silicon elemental maps, while the phase-separated morphologies of polyisoprene rubber (IR) and styrene-butadiene rubber (SBR) are visualized by STEM-tomography in high-angle-annular-dark field (HAADF) mode. The combination of STEM-EDX and STEM-HAADF tomography enables us to determine the distribution of silica between the two rubber phases quantitatively even with high contents of silica up to 70 phr (weight parts per hundred rubber). It is found that silica is preferentially distributed in the SBR phase, but it is also distributed in the IR phase when the IR fraction in the total rubber components is higher than 40 wt%. The preferential distribution of silica in the SBR phase improves the dispersion of the IR domains. This is the first use of this technique for a multicomponent polymer system, showing the advantage to characterize the complicated multicomponent polymer composite morphologies.     

Quantitative determination of corrosion products and adsorbed water on copper in humid air containing SO2 by IR-RAS measurements

The time dependency of the amounts of corrosion products and co-existing adsorbed water on copper in humid air containing SO₂ was estimated from a series of in situ time-resolved IR-RAS spectra on the basis of the relations between the band intensities and the mass changes of the corrosion products, which were determined by simultaneous measurement of IR-RAS and QCM. The amounts of both corrosion products increased slowly at the initial stage and later increased rapidly. Although the relative humidity was kept constant, the amount of adsorbed water increased nearly the same behavior as that of corrosion products in the stage of relatively small amounts of corrosion products and later increased rapidly when the amounts of corrosion products increased. In humid air without SO₂, sulfite gradually decomposed and some of it changed into sulfate.     

Optimum combination of operating parameters in abrasive cut-off

For optimization of abrasive cut-off operation, wheel wear equation must be identified before the operation is optimized. The equation is obtained by using GMDH algorithm with successive determination of trends containing interactive terms. In the model equation factors of grinding fluid are taken into consideration in addition to the factors of wheel, work material, feed (table speed) and wheel speed. For the identification of the model wheel wear tests are performed under the experimental design treating the above-mentioned factors as independent variables. The grinding ratio (output in the model) can be predicted for combinations of various factors using the model. With the wheel wear equation and machining cost model, the optimum combination of wheel, fluid, feed and wheel speed can be selected for a given work material. The relationships between these variables and the costs are investigated.     

Activity measurements of Al and Cu in Si–Al–Cu melt at 1273 and 1373 K by the equilibration with molten Pb

For the effective control of Al introduction to solidified Si during the solidification refining of Si with the Si–Al-based melt for the solar cell material or the LPE Si film growth processes from the Si–Cu–Al solvent, thermodynamic properties of the Si–Al–Cu melt were investigated at 1273 and 1373 K. Activities of Al and Cu in the Si–Al–Cu melt were measured by the equilibration with molten Pb. Also, the excess Gibbs energy of the melt was studied by the ternary regular solution model.

The evaluated thermodynamic properties of the Si–Al–Cu melt indicated that Cu addition to the Si–Al melt brings the smaller activity coefficient of Al and is effective for reducing the Al content of solidified Si from the melt more effectively than its dilution effect for Al.     

500-fps face tracking system

In this paper, we propose a high-speed vision system that can be applied to real-time face tracking at 500 fps using GPU acceleration of a boosting-based face tracking algorithm. By assuming a small image displacement between frames, which is a property of high-frame rate vision, we develop an improved boosting-based face tracking algorithm for fast face tracking by enhancing the Viola–Jones face detector. In the improved algorithm, face detection can be efficiently accelerated by reducing the number of window searches for Haar-like features, and the tracked face pattern can be localized pixel-wise even when the window is sparsely scanned for a larger face pattern by introducing skin color extraction in the boosting-based face detector. The improved boosting-based face tracking algorithm is implemented on a GPU-based high-speed vision platform, and face tracking can be executed in real time at 500 fps for an 8-bit color image of 512 × 512 pixels. In order to verify the effectiveness of the developed face tracking system, we install it on a two-axis mechanical active vision system and perform several experiments for tracking face patterns.     

A coarse-to-fine IP-driven registration for pose estimation from single ultrasound image

A fast registration making use of implicit polynomial (IP) models is helpful for the real-time pose estimation from single clinical free-hand Ultrasound (US) image, because it is superior in the areas such as robustness against image noise, fast registration without enquiring correspondences, and fast IP coefficient transformation. However it might lead to the lack of accuracy or failure registration.In this paper, we present a novel registration method based on a coarse-to-fine IP representation. The approach starts from a high-speed and reliable registration with a coarse (of low degree) IP model and stops when the desired accuracy is achieved by a fine (of high degree) IP model. Over the previous IP-to-point based methods our contributions are: (i) keeping the efficiency without requiring pair-wised correspondences, (ii) enhancing the robustness, and (iii) improving the accuracy. The experimental result demonstrates the good performance of our registration method and its capabilities of overcoming the limitations of unconstrained freehand ultrasound data, resulting in fast, robust and accurate registration.