Low-driving-current temperature-stable 10 Gbit/s operation of p-doped 1.3 /spl mu/m quantum dot lasers between 20 and 90/spl deg/C

Low-driving-current temperature-stable 10 Gbit/s direct modulation was achieved for optimised 200 mum-long short cavity 1.3 mum p-doped quantum dot lasers. Driving conditions were 25.2 mA_p-p for the modulation current and 23.4 mA for the bias current through the whole temperature range from 20 to 90degC     

Seismic proof test of a reinforced concrete containment vessel (RCCV): Part 1: Test model and pressure test

In Japan, the Nuclear Power Engineering Corporation (NUPEC), sponsored by the Ministry of Economy, Trade and Industry (METI), has been conducting a series of seismic reliability proving tests using full-scale or close to full-scale models to simulate actual important equipment that is critical for seismic safety of nuclear power plants. The tests are intended to validate the seismic design and reliability with a sufficient margin even under destructive earthquakes. A series of tests was carried out on a reinforced concrete containment vessel (RCCV) for advanced boiling water reactor (ABWR) from 1992 to 1999. A large-scale high-performance shaking table at Tadotsu Engineering Laboratory, the largest in the world, was used for this test. Part 1 reports the test model and the results of pressure and leak tests. Part 2 describes test procedures, input waves and the results of verification tests such as changes of stiffness, characteristic frequency and damping ratio, the failure of the model and the load deflection. Part 3 shows the seismic safety margin that was evaluated from the energy input during the failure test to a design basis earthquake. Part 4 reports simulation analysis results by a stick model with lumped masses.     

Chemical sensing by an electrical oscillator: Detection and quantification of cationic surfactants

A new chemical sensing system using an electrical oscillator has been developed. This sensing system measures the electrical ‘non-linearity’ at the surface of an electrode immersed in a test solution: a sinusoidal voltage is applied to the electrode and the higher harmonics of the output current are obtained by Fourier transformation. This sensing system has been used to detect and quantify surfactant molecules in solutions. The relative intensity P₂/P₁ of the peaks of the second (P₂) and first (P₁) harmonics in the output current was found to be linearly correlated with the logarithms of the concentrations of cationic surfactants such as cetylpyridium bromide (CPB) and cetyl-N,N,N-trimethylammonium bromide (CTAB), but not with those of the anionic surfactant sodium dodecyl sulfate (SDS) or the neutral surfactant Triton X-100. The reproducibility of this sensing system was shown to be excellent.     

Structural,Thermal and Magnetic Properties of Thin Metal Films and Adsorbate–Substrate Systems Studied by XAFS and XMCD

Thin metal films often exhibit interesting properties that are essentially different from the bulk ones. XAFS (X-ray absorption fine structure) and XMCD (X-ray magnetic circular dichroism) techniques are quite suitable to investigate structural, thermal and magnetic properties of thin metal films. In this proceeding, we will present following two topics concerning structural and magnetic properties of adsorbates on thin metal films. The first one is the adsorption geometry of SO₂ on a 1-monolayer (ML) Pd thin film grown on a Ni(111) single crystal. It was found by S K-edge XAFS that SO₂ is lying flat on 1-ML Pd/Ni(111). This result is not similar to the bulk Pd surface but to the bulk Ni one. This finding indicates significant modification of the electronic structure of the 1-ML Pd film compared to the bulk one. The second topic is the magnetic moment induced on CO adsorbed on Ni epitaxial films grown on Cu(001). The O K-edge XMCD results revealed that in the perpendicularly magnetized 10-ML Ni film the orbital moment of CO is parallel to the substrate Ni magnetization, while it is antiparallel in the in-planar magnetized 6-ML and thick (>100 ML) films. The origin of the induced orbital moment at CO is discussed.     

Marangoni flow at the gas/melt interface of steel

Direct observation with a scanning laser microscope was made to determine the direction and velocity of surface flow of steel melt in the vicinity of the solid/melt (S/M) interface. During solidification, a fast solutal Marangoni flow moving away from the S/M interface was confirmed to exist on steel melts containing oxygen and sulfur of 10 to 105 ppm. Even in such a low range of oxygen and sulfur content, the solutal Marangoni flow can be very fast, carrying inclusion particles up to the free surface along the S/M interface. During heating and holding, however, a thermal Marangoni flow combined with convective flow generated a reverse flow directed toward the S/M interface. These features have important relevance to inclusion entrainment and solute segregation during the solidification of steel. This article is based on a presentation given in the Mills Symposium entitled “Metals, Slags, Glasses: High Temperature Properties & Phenomena,” which took place at The Institute of Materials in London, England, on August 22–23, 2002.     

Finite element analysis of magnetic circuits composed of axisymmetric and rectangular regions

A new approximate method is developed for calculating three-dimensional magnetic fields in magnetic circuits composed of connected axisymmetric and rectangular regions. Using this new method, fairly accurate solutions can be obtained when the leakage flux from the magnetic circuit is small. In this paper, the new method is explained and then the usefulness of the technique is clarified by comparing calculated and measured flux densities.     

Radiotherapy for carcinoma of the esophagus in aged patients

One hundred fifty-four patients with esophageal carcinoma were treated with either irradiation alone or irradiation combined with surgery at the University of Occupational and Environmental Health Hospital between January 1980 and February 1992. The number of patients 75 years old and older was 25. In patients 74 years old and younger, the overall five-year survival rate by Kaplan-Meier method was 24.5%. The survival rate was best in the patients who were treated by a combination of irradiation and surgery. In patients 75 years old and older, the one-year survival rate was 59%, and the three-year rate was 20%. Aged patients had a tendency to be worse in performance status, and there was no correlation between treatment modality and survival time. We conclude that radiotherapy is useful for treating esophageal cancer in aged patients particularly when maintenance of the quality of life is considered.     

The complex aerodynamic footprint of desert locusts revealed by large-volume tomographic particle image velocimetry

Particle image velocimetry has been the preferred experimental technique with which to study the aerodynamics of animal flight for over a decade. In that time, hardware has become more accessible and the software has progressed from the acquisition of planes through the flow field to the reconstruction of small volumetric measurements. Until now, it has not been possible to capture large volumes that incorporate the full wavelength of the aerodynamic track left behind during a complete wingbeat cycle. Here, we use a unique apparatus to acquire the first instantaneous wake volume of a flying animal''s entire wingbeat. We confirm the presence of wake deformation behind desert locusts and quantify the effect of that deformation on estimates of aerodynamic force and the efficiency of lift generation. We present previously undescribed vortex wake phenomena, including entrainment around the wing-tip vortices of a set of secondary vortices borne of Kelvin–Helmholtz instability in the shear layer behind the flapping wings.     

添加合金元素对奥氏体不锈钢等离子渗氮和渗碳的影响

奥氏体不锈钢众所周知有良好的耐蚀性,但是在工业上没有用于承受摩擦的工件上,因为它的硬度低,摩擦磨损性能差。奥氏体不锈钢经低温等离子体渗氮或渗碳能生成一层特殊的氮化物或碳化物层,称为S相,它具有高的硬度和优良的耐蚀性。这项研究中各种奥氏体不锈钢都经低温等离子体渗氮或渗碳,用各种分析技术研究了添加合金元素对S相特性的影响,用了光学显微镜和电子显微镜观察,做了X射线衍射分析,在5%H2SO4溶液中测量阳极极化,用球对平面摩擦装置做摩擦磨损测试。氮化物或碳化物层厚度随处理温度增加而加厚,AISI316钢上生成的渗层厚度是所有的基体钢材中最厚的。超过临界温度,由于氮化铬工碳化铬沉淀使耐蚀性降低。临界温度由渗氮的基材决定。另一方面,在渗碳层中临界温度不随基材变化。大部分样品上S相层的耐蚀性比没有处理的不锈钢的低。但是,AISI316和JIS-SUS304J3钢在400℃渗碳后都有和未处理钢一样优良的耐蚀性。每种不锈钢经渗氮或渗碳后耐磨性都有明显的改进。     

Hydrogen production by combining two types of photosynthetic bacteria with different characteristics

The double-layer photobioreactor using two types of photosynthetic bacteria, Rhodobacter sphaeroides RV and its reduced-pigment mutant, MTP4, was developed for efficient hydrogen production. The two types of bacteria had different characteristics on light energy, hydrogen production rate and conversion efficiency. MTP4 produced hydrogen more efficiently under high light conditions and RV did so under low light conditions. Illuminated light toward the surface of a photobioreactor quasi-exponentially declines as it penetrates into the reactor. When two types of bacteria were placed using the developed reactor according to this light distribution, the hydrogen production rate reached 3.64 l/m²/h at a light intensity of 500 W/m² in 24 h and the conversion efficiency of light energy to hydrogen was 2.18%. These values were 33% higher than those of only using RV. The low light in the deep part of the reactor was utilized efficiently, resulting in a higher hydrogen production rate.