CVCF inverter based on nonlinear control of instantaneous active and reactive power and its operation characteristics

This paper describes a direct‐power‐controlled CVCF inverter and presents its experimentally examined operation characteristics. The most important feature of this strategy is the direct selection of the switching states of the CVCF inverter to restrict errors between the feedback and command values of active and reactive power. In addition, this paper presents a theoretical analysis of the relationship between the instantaneous power and the switching state, which is essential for deriving a switching‐state table for the controller. The feasibility of the proposed method was verified through several computer simulations and experimental tests using a 2.0‐kVA prototype setup. The output voltages were confirmed to be stable sinusoidal waveforms with a total harmonic distortion of 1.13% under nonlinear load conditions. Excellent voltage balance was achieved by the proposed strategy even under unbalanced load conditions. © 2010 Wiley Periodicals, Inc. Electr Eng Jpn, 174(3): 62–69, 2011; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21023     

Microstructural modification and mechanical property improvement in friction stir zone of thixo-molded AE42 Mg alloy

Thixo-molded AE42 Mg alloy was friction stir welded, and the soundness of joints was evaluated, together with the microstructure evolution and mechanical properties in friction stir zones. According to X-ray radiography, the optimum FSW condition range of AE42 alloy exists between AZ61 and AZ31 alloys, and it seems that the optimum welding condition range increases with decreasing Al content in the Mg alloys. There are mainly two kinds of compounds in the thixo-molded AE42 alloy, and FSW has little influence on the grainy Al₁₀RE₂Mn₇ compound, but it has great influence on Al₁₁RE₃ phase, which is changed from lamellar eutectic to small particles after welding. Furthermore, the average diameter of Al₁₁RE₃ particles in SZ decreases with increasing the traveling speed at constant rotation speed due to less heat input. The hardness in SZ is higher than that in BM, and tensile strength and elongation are both improved after welding because the stirring refines and uniforms the microstructure and intermetallic compounds.     

Molecular characterization of morphologically typical human calicivirus Sapporo

Human calicivirus Sapporo (SV) has typical calicivirus morphology and causes acute gastroenteritis in children. The nucleotide sequence of 3.2 kb of the 3' end of SV was determined from a cloned cDNA. The 3' end of the SV genome is predicted to encode the RNA-dependent RNA polymerase region, the capsid protein and two small open reading frames. The nonstructural and capsid protein coding sequences in the SV genome are fused in a single open reading frame. The organization of these proteins in the SV sequence is similar to that of rabbit hemorrhagic disease virus and the recently described Manchester virus, and distinct from the genome organization of the prototype human calicivirus, Norwalk virus, that lacks typical calicivirus morphology and has been described as a small round structured virus (SRSV). Sequence analysis of the predicted capsid region showed that the SV capsid is longer by approximately 30 amino acids than the capsid of any of the SRSVs, and multiple sequence alignments showed that these additional amino acids are located in the variable region of the capsid protein. Expression of the capsid protein of SV in insect cells resulted in the self-assembly of virus-like particles that have a morphology similar to that of the native virus. This result shows that calicivirus morphology is determined by the primary sequence of the capsid protein.     

Free vibration of coil springs of arbitrary shape

This paper is concerned with the method for solving the vibration problem of coil springs of arbitrary shape. In the analysis the exact field transfer matrix is derived from the solution of the fundamental equation of the three-dimensional curved beam theory. The transfer matrix is given by combining this field transfer matrix and the point transfer matrix. The analysis derives the frequency equation which is applicable to coil springs of general shape. Numerical calculations have been carried out for hyperboloidal springs and barrel springs. Experimental tests also have been carried out to verify the present results.     

Secondary neutral and ionized particle measurements under MeV-energy ion bombardment

We have measured both secondary neutral and ionized particles from an InSb target under 3.0 MeV Si ion bombardment. Measurements of both ions and neutrals have not been carried out so far in the MeV-energy range. The mass spectra and axial emission energy distributions of secondary particles were investigated. Secondary ions were measured with a linear- and a reflective-type time-of-flight technique, whereas secondary neutral particles were photo-ionized by a UV pulsed laser (ArF: 193 nm) and measured with a reflective-type time-of-flight technique. Different results were obtained for neutral particles in comparison with ionized particles. The mean energy of neutral Sb atoms was much lower than that of neutral In atoms, whereas the mean energies of secondary In and Sb ions were nearly equal.     

Mechanism of welding fume suppression during AC-pulsed MIG welding of Al-Mg alloys

Welding fume, inevitably generated during arc welding processes, may be a source of occupational pneumoconiosis when persistently inhaled in the long term and accordingly merits serious consideration in occupational hygiene respects. To improve the working environment at welding sites, it is imperative to ensure total air exchange at work sites, local extraction in the vicinity of welding facilities, and the wearing of respiration protection devices in other respects.¹ Currently available preventive measures, however, suffer from a number of drawbacks, such as heavy investments needing to be made in equipment and facilities and operability being obstructed by the wearing of respiration protection devices. Alongside such passive measures, it is desirable to develop welding materials or methods able to suppress welding fume generation at source.     

Chemical dehydrofluorination and electrical conductivity of poly(vinylidene fluoride) films

The dehydrofluorination of poly(vinylidene fluoride) (PVDF) powder and films was studied using several kinds of base solution. Especially the reactivity of 1,8-diazabicyclo[5.4.0]-7-undecene (DBU) in ethanol, KOH in 2-propanol and aqueous NaOH solution with tetrabutylammonium bromide was investigated by the change in infrared (IR) and ultraviolet-visible (UV-VI) absorptions of PVDF films. The elimination reactions by DBU or KOH were considered to be accompanied by substitution reaction. The electrical conductivity of dehydrofluorinated PVDF films increased markedly by doping with iodine, and the activation energies of conduction were found to be between 0.4 and 0.5 eV. When a drawn PVDF film was dehydrofluorinated and doped with iodine, anisotropy in conductivity was observed.     

High speed welding of aluminium alloy sheets with using the laser/AC pulsed MIG hybrid process

The reduction of energy consumption has become the global task in recent years as a countermeasure to address the global warming issue caused by the mass discharge of carbon dioxide. The volume of carbon dioxide emission from automobiles has become approximately 21 % of the total emission by volume, so improved fuel efficiency is strongly urged and the development and application of new technologies have been actively implemented; the technologies required to reduce the weight of the automobile body, in particular, has attracted a much attention.¹ Amongst these, aluminium alloys have a high strength for their light weight and have superior recycling properties, so the move to reduce the automobile body weight by replacing the existing materials with aluminium alloys has progressed rapidly and totally aluminium alloy automobiles have now become commercially available.²     

Maximum‐power‐point tracking method of photovoltaic power system using a single transducer

This paper describes a novel strategy of maximum‐power‐point tracking for photovoltaic power generation systems. A unique feature of this method is the capacity to see the maximum power point using only a single transducer, that is, a Hall‐effect CT or an isolation amplifier. Output power of the photovoltaic can be estimated with an average value and ripple amplitude of the detected reactor current or the capacitor voltage. A conventional hill‐climbing method is employed to seek the maximum power point, using the output power estimated with only the current or voltage transducer. In this paper, not only a theoretical aspect of the proposed method is discussed, but also experimental results are presented to prove the feasibility of the method. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 160(1): 79– 86, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20275