The Mechanical Behaviour of Polyimide/Copper Laminates Part 2: Peel Energy Measurements

The mechanical peel behaviour of laminates consisting of polyimide films adhered to copper foil using a modified acrylic adhesive has been studied over a wide range of test rates and temperatures. The laminates were prepared from polyimide films which had been subjected to either a “high-thermal history” or a “low-thermal history” treatment during the production of the film. The measured peel energies of the laminates could be superimposed to give a master curve of peel energy versus the reduced rate of peel test, Ra_T, where R is the rate of peel test and a_T is the time-temperature shift factor. The appropriate shift factors were a function of the test temperature and were mainly deduced from tensile tests conducted on the bulk adhesive. The “high-thermal history” laminates gave higher peel energies and the locus of failure of the laminates was mainly by cohesive fracture through the adhesive layer. At low values of log₁₀ Ra_T, i.e. Low rates of peel and high test temperatures, the “low-thermal history” laminates also failed in the adhesive layer and possessed similar peel energies to those measured for the “high-thermal history” laminates. However, at high log₁₀ Ra_T values, the peel energies measured for the “low-thermal history” laminates were lower and showed a wider scatter. These arose from a different locus of failure occurring in these “low-thermal history” laminates when tested under these conditions. Namely, it was found that most of these laminates failed in a weak boundary layer in the outer regions of the “low-thermal history” polyimide film.     

An NMR study of the dissociation of N,N′-(2-propyloximino)-4,4′-methylenebis(phenylcarbamate) and its crosslinking of polymers containing labile hydrogens. II

Nuclear magnetic resonance spectroscopy has been used to study the dissociation and reaction of N,N′-(2-propyloximino)-4,4′-methylenebis(phenylcarbamate), as a crosslinking agent for polymers containing labile hydrogens. The crosslinking of poly(acrylic acid), polyacrylamide, and poly(vinyl alcohol) was found to result upon heating each to 150°C for 10 min with this component at 2–10 wt %.     

ABSORPTION AND DESORPTION TO AND FROM LIQUID FILMS ON INCLINED PLANES

Two published theoretical models are examined and applied to experimental results for absorption and desorption. The system used was CO₂/H₂O and studies were made for liquid film flow down inclined planes. Experimental results give “Reduced” values of mass ransfer rates.

Interferometric studies give interfacial concentration, penetration and film depths, and take-up of carbon dioxide. In the case of desorption the interferograms are distorted by “deflections.”

All the experimental values for absorption and desorption differ from those calculated from theoretical models.

Desorption is not a mirror image of absorption, and it is approximately 75% of the transfer rate of absorption over a wide operating range.

A comparison is made of the behaviour of static pools and flowing liquid films.     

Separation of crude palm oil components by semipreparative supercritical fluid chromatography

Successful separation of triglycerides, diglycerides, free fatty acids, carotenes, tocopherol, and tocotrienols from crude palm oil has been achieved by supercritical fluid chromatography (SFC) with a combination of a C18 and a silica gel column. The separation was carried out by the programmed extraction elution method. Free fatty acids were separated into five components by gas-liquid chromatography; tocopherol and tocotrienols were also separated into four components by SFC analysis, and the pure fractionated carotenes were obtained by preparative SFC. Thus, by using supercritical fluid chromatography, crude palm oil components can be separated and fractionated, based on differences in their functional groups.     

Isosteric heat of sorption of CO2 in poly(ethylene terephthalate)

Sorption isotherms for carbon dioxide in poly(ethylene terephthalate) have been measured at 35–55°C. The isotherms were measured gravimetrically on a Mettler Thermoanalyzer-1 from vacuum to 1 atmosphere. The sorption data were used to generate sorption isotherms from which the isosteric heat of sorption of CO₂ in PET was determined. At 45°C the isosteric heat of sorption increases from −10 kcal/mole at a concentration of 0.5 cm³ (STP)/cm³ (polymer) to −8 kcal mole⁻¹ at a concentration of 1.5 cm³ (STP)/cm³ (polymer). It has been reported in the literature that the isosteric heat of sorption for this system decreased through a minimum before increasing with increasing concentration. Our measurement of the low-pressure sorption isotherms shows that this is not the case.     

Spatial navigation model based on chaotic attractor networks

We present a model of spatial navigation based on the non-convergent dynamics of brain activity. The system includes a hippocampal module that processes global spatial information and a cortical module that deals with local sensory information. We test the model using several spatial navigation paradigms: goal finding, shortcutting and detouring. Computer simulations show that the performance of the agent qualitatively matches that of animals and related models. This new approach provides a novel interpretation of how the brain accomplishes spatial navigation.     

In-focus electron microscopy of frozen-hydrated biological samples with a Boersch phase plate

We report the implementation of an electrostatic Einzel lens (Boersch) phase plate in a prototype transmission electron microscope dedicated to aberration-corrected cryo-EM. The combination of phase plate, C_s corrector and Diffraction Magnification Unit (DMU) as a new electron-optical element ensures minimal information loss due to obstruction by the phase plate and enables in-focus phase contrast imaging of large macromolecular assemblies. As no defocussing is necessary and the spherical aberration is corrected, maximal, non-oscillating phase contrast transfer can be achieved up to the information limit of the instrument. A microchip produced by a scalable micro-fabrication process has 10 phase plates, which are positioned in a conjugate, magnified diffraction plane generated by the DMU. Phase plates remained fully functional for weeks or months. The large distance between phase plate and the cryo sample permits the use of an effective anti-contaminator, resulting in ice contamination rates of <0.6 nm/h at the specimen. Maximal in-focus phase contrast was obtained by applying voltages between 80 and 700 mV to the phase plate electrode. The phase plate allows for in-focus imaging of biological objects with a signal-to-noise of 5-10 at a resolution of 2-3 nm, as demonstrated for frozen-hydrated virus particles and purple membrane at liquid-nitrogen temperature.