Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

部分种子成分的特征X射线在等效生物材料中衰减的测定

用Ｓｉ（Ｌｉ）探测器实现了Ｎａ、Ｍｇ、Ｓ、Ｃｌ的特征Ｘ射线在有机膜中的相对衰减以及与Ｏ、Ｋ元素的特征Ｘ射线能量相当的Ｘ射线或轫致辐射在有机膜中的相对衰减，分别得出了它们减的数学描述，并把实验得到不同能量的Ｘ射线在有机膜中的质量吸收系数与Ｂｅｒｋｅｌｅｙ的ＯＣＧ软件计算出的结果相比，相关都小于３０％。     

化学束外延

本文介绍了化学束外延(CBE)的发明和发展,论述了CBE的原理和设备。文中还介绍了最近提出的一种生长机理。     

Synthesis, characteristics and oxygen-sensitive properties of SrMgxTi 1 − xO3 nanocrystals

SrMg_xTi_{1 - x}O₃ nanocrystals (x = 0.1–0.6) were synthesized by the stearic acid gel method. Powder samples were characterized by X-ray diffraction and X-ray photoelectron (XP) spectroscopy. The results showed that the lattice parameter a and the O 1s XP spectrum changed not only with the Mg content x but also with the grain size d of the samples. The conductivity of a thick film specimen fabricated on an aluminium oxide wafer was investigated in a nitrogen—oxygen atmosphere.     

工业汽轮机的清洗

本文介绍了用饱和蒸汽对冷凝式汽轮机进行清洗除垢时主要参数的确定、操作要点及清洗方案，清洗后的汽轮机运行正常。     

A high-current and high-temperature 6H-SiC thyristor

A 6H-SiC thyristor has been fabricated and characterized. A forward breakover voltage close to 100 V and a pulse switched current density of 5200 A/cm² have been demonstrated. The thyristor is shown to operate under pulse gate triggering for turn-on and turn-off, with a rise time of 43 ns and a fall time of less than 100 ns. The forward breakover voltage is found to decrease by only 4% when the operating temperature is increased from room temperature to 300°C. It is found that anode ohmic contact resistance dominates the device forward drop at high current densities     

Patient's self-interpretation of tuberculin skin tests

BACKGROUND: In the outpatient use of tuberculin skin testing (purified protein derivative [PPD]), it is at times inconvenient to have a patient revisit for interpretation. Therefore, we assessed patients' ability to self-interpret these test results. METHODS: In keeping with prior custom, patients were seen by an experienced nurse, who performed skin testing with PPD intermediate strength as well as mumps and Candida anergy control tests in some cases, and explained the procedure. The patients were asked to return 48 to 72 h later, at which time one of the researchers recorded their test interpretations before they were again evaluated by the nurse. RESULTS: Sixty-eight patients were studied, of whom 59 returned at appropriate interval. Eighteen patients had a positive PPD test reaction of 10 to 20 mm induration, which only one patient correctly identified as a positive test result. However, positive anergy control tests were correctly interpreted in 10 of 27 cases. CONCLUSION: The small number of positive PPD test result recognition by these patients may be partially attributed to their lack of education, as well as foreign birth and denial of illness. PPD results should be checked by an experienced professional.     

特征X射线能谱法测定Fe^＋注入小麦种子的深度

用１１０ｋｅＶ Ｆｅ＾＋离子束垂直注入小麦种胚后，在扫描电子显微镜上沿种子纵沟剖面，在不同深度上测量Ｆｅ元素被激发出的特征Ｘ射线强度分布，结果表明分布呈指数衰减，与晶体中的热扩散分布相类似，并对此进行了讨论。     

Temperature dependence of hydrogenated amorphous silicon thin-film transistors

The temperature dependence characteristics of hydrogenated amorphous silicon thin-film transistors were investigated. The results indicate that as the temperature was increased, the threshold voltage and the field-effect mobility were first increased, and then decreased, which may be controlled by different mechanisms at low and high temperatures. In addition, if the temperature was higher than 420 K, the Fermi level was promoted to the degenerate-like states, the current channel always existed due to the temperature effect, and the threshold voltage became negative.     

HHD型核子秤电离室物理性能检测

HHD型核子秤电离室已成功地使用于HCS型核子秤.对它的各种物理性能指标进行了检测,各项性能指标都达到了设计要求。