氢型丝光沸石催化剂催化α-蒎烯合成α-松油醇

在相转移助剂苄基三乙基氯化铵(BTEAC)存在下,以氢型丝光沸石(HM)为催化剂,原料α-蒎烯经开环、重排及水合反应一步法合成了α-松油醇。研究了各种因素对α-蒎烯转化率及α-松油醇收率的影响,采用5因素4水平L16(45)进行了正交实验,得出最佳的工艺条件:反应温度80℃,w(BTEAC)=15%,m(HM)∶m(α-蒎烯)=0.6,反应时间40h,m(乙酸乙酯)∶m(α-蒎烯)=0.9。在此条件下,α-蒎烯转化率为75.2%,α-松油醇收率为42.0%。用气相色谱-质谱联用仪对反应产物进行分析,共鉴定出14种化合物,主要成分为α-松油醇、α-蒎烯、柠檬烯、桉叶油素、异松油烯、龙脑等。实验得到的α-松油醇具有光学活性,旋光值[α]=+61°,同时香气纯正,可用于制作香料。     

双膦胺镍-甲基铝氧烷体系催化苯乙烯聚合

研究了具有新型结构的双膦胺镍配合物N,N-双(二苯膦基)-对甲氧基苯胺二氯化镍-甲基铝氧烷(PNP-N i-MAO)催化体系对苯乙烯聚合的催化性能,考察了聚合温度、n(A l)∶n(PNP-N i)、PNP-N i的浓度和苯乙烯的浓度对催化活性、苯乙烯转化率、聚苯乙烯相对分子质量及其分布的影响,并用核磁共振和凝胶色谱对聚苯乙烯的结构进行了表征。实验结果表明,在聚合温度25℃、聚合时间1h、n(A l)∶n(PNP-N i)=300、c(苯乙烯)=2.3m ol/L、c(PNP-N i)=0.4mm ol/L、甲苯为溶剂的适宜条件下,苯乙烯的转化率可达95%以上,催化活性达到5×105g/(m ol.h)左右。核磁共振和凝胶色谱表征结果显示,所得聚苯乙烯为无规结构,重均相对分子质量约为1×104,相对分子质量分布Mw/Mn约为2。     

抵御已知/选择明文攻击的混沌图像加密算法

论文在对现有一类典型图像混沌加密算法的分析基础上,提出了一种改进的图像混沌加密算法。该算法引入小波变换,可以有效地克服一些混沌加密算法不能抵御已知/选择明文攻击的缺陷。     

MPTA型原油脱金属剂的工业应用

在对高金属含量原油进行初步评价的基础上，利用SH—Ⅰ型电脱盐试验仪对自主开发的MPTA型原油脱金属剂进行了原油脱金属的实验室研究。结果表明，当MPTA型脱金属剂加入量为250μg／g时，钙的脱除率可达97．4％，并且对其它金属元素，如镍、铁、钠、锰、铝和钒也有明显的脱除效果。该剂在山东恒源石油化工股份有限公司重交沥青车间500kt／a的电脱盐装置上进行原油脱金属工业试验的结果表明，经过二级电脱盐处理后，钙的脱除率达到99．1％，钠的脱除率为94．6％，铁的脱除率为82．9％，并可在一定程度上降低原油中镍和铜的含量。使用MPTA型原油脱金属剂显著降低了一、二级电脱盐装置的电场电流，有利于炼油厂的节能降耗。     

Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

Wavelength and Waveband Assignment for Ring Networks Based on Parallel Multi‐granularity Hierarchical OADMs

In this paper we study the optimization issues of ring networks employing novel parallel multi‐granularity hierarchical optical add‐drop multiplexers (OADMs). In particular, we attempt to minimize the number of control elements for the off‐line case. We present an integer linear programming formulation to obtain the lower bound in optimization, and propose an efficient heuristic algorithm called global bandwidth resource assignment that is suitable for the design of large‐scale OADM networks.     

HDI工艺中取代涂树脂铜箔适合激光钻孔的半固化片

应用于HDI的激光钻孔半固化片的方法和其它常规材料相比具有的优缺点。     

X80焊管H_2S环境应力腐蚀开裂行为研究

采用三点弯曲加载法和微电极扫描测试技术,研究了X80高强度级管线钢及其焊缝区的抗H2S环境应力腐蚀开裂(SSCC)行为。测定了焊接接头的显微硬度分布,分析了显微组织结构、力学性能及抗腐蚀性能之间的相关性。研究表明,热影响区(HAZ)对应力腐蚀开裂最为敏感,母材的纵向和横向取样对应力腐蚀敏感性影响不显著,薄壁管材比厚壁管材有较好的抗H2S环境应力腐蚀性能。HAZ晶粒粗大、硬度高,局部腐蚀倾向大,由此导致该区SSCC敏感性高。     

Supermedia-enhanced Internet-based telerobotics

This paper introduces new planning and control methods for supermedia-enhanced real-time telerobotic operations via the Internet. Supermedia is the collection of video, audio, haptic information, temperature, and other sensory feedback. However, when the communication medium used, such as the Internet, introduces random communication time delay, several challenges and difficulties arise. Most importantly, random communication delay causes instability, loss of transparency, and desynchronization in real-time closed-loop telerobotic systems. Due to the complexity and diversity of such systems, the first challenge is to develop a general and efficient modeling and analysis tool. This paper proposes the use of Petri net modeling to capture the concurrency and complexity of Internet-based teleoperation. Combined with the event-based planning and control method, it also provides an efficient analysis and design tool to study the stability, transparency, and synchronization of such systems. In addition, the concepts of event transparency and event synchronization are introduced and analyzed. This modeling and control method has been applied to the design of several supermedia-enhanced Internet-based telerobotic systems, including the bilateral control of mobile robots and mobile manipulators. These systems have been experimentally implemented in three sites test bed consisting of robotic laboratories in the USA, Hong Kong, and Japan. The experimental results have verified the theoretical development and further demonstrated the stability, event transparency, and event synchronization of the systems.     

Fatigue crack growth in SiC particulates reinforced Al matrix graded composite

The SiC/Al graded composite was fabricated by powder metallurgy processing and its fatigue crack growth behavior was studied. The volume percentage of SiC particulates was distributed from 5 to 30% layer by layer on the cross section. Since the aluminium was dissolved together, there was no evident interface between the two layers with different volume fraction of SiC particulates. Fatigue crack growth was in direction of from 5 to 30% SiC layers under sinusoidal wave-form. The retardation of fatigue crack growth was found when crack propagated from low volume fraction of SiC to high volume fraction of SiC. The crack deflection and branching between two layers were observed, which decreased crack growth rates. In view of crack tip driving force, the plasticity mismatch between the layers shielded crack tip driving force, i.e. decreased the effective J-integral at the tip of the crack as the plastic zone of the crack tip spread from the weaker material into the stronger material.