Rolling and Lifting Probabilities for Sediment Entrainment

This study addresses the rolling and lifting probabilities for sediment entrainment by incorporating the probabilistic features of the turbulent fluctuation and bed grain geometry. The lognormally distributed instantaneous velocity and uniformly distributed initial grain position, along with a relation between lift coefficient and particle Reynolds number, are used to extend the theoretical formulation of the entrainment probabilities in smooth-bed flows. The two threshold conditions identified herein enable us to precisely define the probabilities of entrainment in the rolling and lifting modes. The results obtained in this study coincide well with the published data. The lifting probability increases monotonously with the dimensionless shear stress θ, which is consistent with the earlier results yet displays improved agreement with the experimental data. The maximum value of rolling probability, with a magnitude of 0.25, occurs at θ ≈ 0.15. For θ<0.05 (or θ>0.6), the rolling (or lifting) probability makes up more than 90% of the total entrainment probability and thus can be used as an approximation to the total probability of entrainment. The proposed rolling and lifting probabilities are further linked to the two separate criteria for incipient motion to explore the critical entrainment probabilities. The results reveal that a consistent probability corresponding to the critical state of sediment entrainment cannot be found.     

自蔓延高温合成TiNi多孔体合金

为了开发新型的生体材料，本文对自蔓延高温合成TiNi多孔体合金——人造骨材料进行了研究。以单质钛粉和镍粉作原料，在氩气保护条件下，采用预热点燃模式和热爆模式制得了不同形态的多孔TiNi形状记忆合金。采用SEM和XRD分析了样品的孔洞特征和相组成，测试了其力学性能，并研究了合成条件参数与样品表面形貌和孔隙状态之间的关系。结果表明，用SHS法制备TiNi多孔体合金是可行的。     

阜新市细河改造工程坝基渗漏计算及处理效果分析

阜新市细河改造工程由四座橡胶坝和两岸防洪大堤组成，由于堤(坝)基第四系冲洪积层广泛发育，存在渗漏同题。合理选择施工处理方案，是工程成功的关键。作者根据场区不同的地质条件环境条件采取有针对性的不同处理方案，既解决了防渗问题又缩短了施工工期，降低工程造价，取得了很好的经济效益和社会效益。     

Analysis and Optimization of the Energy Efficiency in the 802.11 DCF

This paper introduces an analytical model to investigate the energy efficiency of the IEEE 802.11 distributed coordinated function (DCF). This model not only accounts for the number of contending nodes, the contention window, but also the packet size, and the channel condition. Based on this model, we identify the tradeoff in choosing optimum parameters to optimize the energy efficiency of DCF in the error-prone environment. The effects of contention window and packet size on the energy efficiency are examined and compared for both DCF basic scheme and DCF with four-way handshaking. The maximum energy efficiency can be obtained by combining both the optimal packet size and optimal contention window. To validate our analysis, we have done extensive simulations in ns-2, and simulation results seem to match well with the presented analytical results. The Ohio Board of Regents Doctoral Enhancements Funds and the National Science Foundation under Grant CCR 0113361 have supported this work. Xiaodong Wang received his B.S. degree in communication engineering from Beijing Information Technical Institute of China in 1995, and his M.S. degree in electric engineering from Beijing University of Aeronautics and Astronautics of China in 1998. He joined China Telecom in 1998 where he worked on communication protocols for telecommunication. From June 2000 to July 2002, he worked on GSM base station software development at Bell-labs China, Beijing, China. Currently he is a Ph.D. student in Computer Engineering at University of Cincinnati. His research activities include wireless MAC protocols, energy saving for wireless sensor networks. He is a student member of the IEEE. Jun Yin received the BS degree in automatic control from Dalian Railway Institute of China in 1997, and the MS degree in flight control from Beijing University of Aeronautics and Astronautics of China in 2001. Since 2001 she has been a Ph.D. student in the OBR Research Center for Distributed and Mobile Computing at the University of Cincinnati. Her research interests include performance evaluation of 802.11 MAC protocol, wireless ad hoc networks and sensor networks. She is a student member of the IEEE. Dharma P.Agrawal IEEE Fellow, 1987; ACM Fellow, 1998; AAAS Fellow, 2003 Dr. Agrawal is the Ohio Board of Regents Distinguished Professor of Computer Science and Computer Engineering in the department of Electrical and Computer Engineering and Computer Science, University of Cincinnati, OH. He has been a faculty member at Wayne State University, (1977–1982) and North Carolina State University (1982–1998). He has been a consultant to the General Dynamics Land Systems Division, Battelle, Inc., and the U. S. Army. He has held visiting appointment at AIRMICS, Atlanta, GA, and the AT&T Advanced Communications Laboratory, Whippany, NJ. He has published a number of papers in the areas of Parallel System Architecture, Multi computer Networks, Routing Techniques, Parallelism Detection and Scheduling Techniques, Reliability of Real-Time Distributed Systems, Modeling of C-MOS Circuits, and Computer Arithmetic. His recent research interest includes energy efficient routing, information retrieval, and secured communication in ad hoc and sensor networks, effective handoff handling and multicasting in integrated wireless networks, interference analysis in piconets and routing in scatternet, use of smart directional antennas (multibeam) for enhanced QoS, Scheduling of periodic real-time applications and automatic load balancing in heterogeneous workstation environment. He has four approved patents and three patent filings in the area of wireless cellular networks.     

Hermetic Packaging Using Eutectic SnPb Solder and Cr/Ni/Cu Metallurgy Layer

We have developed an easy, low-cost, and low-temperature optoelectronic hermetic packaging technology utilizing the eutectic SnPb solder and the Cr/Ni/Cu bonding pad. Bonding characteristics of the design were investigated in three different setups: silicon-silicon, silicon-glass, and glass-glass samples. Hermeticity was achieved at 200 degC without flux for all samples during the final bonding process. The bonding pads did not dewet during or after the reflow process. By utilizing the eutectic SnPb solder, the self-alignment process can be achieved. Because the bonding process was conducted through visual alignment, original misalignment was estimated to be more than 100 mum. The surface tension of melting solder during the reflow process allowed the samples to self-align and obtain a misalignment of less than 20 mum after solidification, which was 4% of the entire solder width. The bonding strength of the three setups ranged from 3 to 10 MPa. Among the three setups, glass-glass samples appear to have the strongest bonding strength. This low-temperature and cost-effective soldering process has demonstrated its feasibility and potential utilization in optoelectronic packaging     

On Striping Traffic over Multiple IEEE 802.11(b) Wireless Channels

Due to interference, path loss, multipath fading, background noise, and many other factors, wireless communication normally cannot provide a wireless link with both a high data rate and a long transmission range. To address this problem, striping network traffic in parallel over multiple lower-data-rate but longer-transmission-range wireless channels may be used. In this paper, we propose a new striping method and evaluate its performances over multiple IEEE 802.11(b) channels under various conditions. Our extensive simulation results show that this method is quite effective for such an application. S.Y. Wang is an Associate Professor of the Department of Computer Science and Information Engineering at National Chiao Tung University, Taiwan. He received his Master and Ph.D. degree in computer science from Harvard University in 1997 and 1999, respectively. His research interests include wireless networks, Internet technologies, network simulations, and operating systems. He is the author of the NCTUns 2.0 network simulator and emulator, which is being widely used by network and communication researchers. More information about the tool is available at http://NSL.csie.nctu.edu.tw/nctuns.html. C.H. Hwang received his master degree in computer science from NCTU in 2002 and currently is working for a network company. C.L. Chou currently is a third-year Ph.D. student at the Department of Computer Science and Information Engineering, National Chiao TungUniversity (NCTU), Taiwan. He received his master degree in computer science from NCTU in 2002.     

水性涂料VOC测定偏差对计算结果的影响

阐述水性涂料VOC的三项测定偏差对计算VOC结果的影响 ,指出国内现有标准的检测方法与国际标准方法存在的差距     

On inversive maximal period polynomials over finite fields

Over finite field GF(q) withq a power of an odd primep, we characterize inversive maximal period polynomials in terms of polynomials of orderq + 1, and then we study some properties of polynomials of orderq + 1.This paper was written while the author was visiting the Institute of Information Processing, Austrian Academy of Sciences, AustriaThe author would like to thank the Institute of Information Processing, Austrian Academy of Sciences, Austria, for its hospitality and for using its facilities     

图形电镀铜的常见缺陷及故障排除

本文主要阐述印制电路板生产中图形电镀铜常见缺陷及成因,查找影响其品质的因素和工序并结合相关生产制定相应的预防措施,有效提高产品质量。     

隧道受震破壞調查分析與修復管理案例

就隧道震後之災損模式進行統計與災損原因研判,並利用數值分析方法研判安全性,就結構加固等改善措施之設計考量作詳細說明;另由於隧道結構物的損壞範圍大,且修復經費受限,必須藉由定期檢测進行長期維護管理,以防範意外發生。於此,利用Vidco-GIS自動化影像地理资訊系統之e化新技術,以動態及靜態影像紀錄隧道災損狀況,同時亦整合建置前期設計、施工圖及定期維護等資料,相關成果以資料庫方式纳入日常維護管理,以有限人力有效率地進行維護管理紀錄並随時掌握現況供作決策之明確參考。