Performance improvement and analysis of a 1.6 μm continuous-wave modulation laser absorption spectrometer system for CO2 sensing

In a previous study, we developed a 1.6 μm continuous-wave (cw) modulation laser absorption spectrometer system for CO(2) sensing and demonstrated the measurement of small fluctuations in CO(2) corresponding to a precision of 4 parts per million (ppm) with a measurement interval of 32 s. In this paper, we present the process to achieve this highly specific measurement by introducing important points, which have not been shown in the previous study. Following the results of preliminary experiments, we added a function for speckle averaging on the optical antenna unit. We additionally came up with some ideas to avoid the influences of etalon effects and polarization dependence in optical components. Because of the new functions, we realized a calibration precision of 0.006 dB (rms), which corresponds to a CO(2) concentration precision of less than 1 ppm for a 2 km path. We also analyzed the CO(2) sensing performance after the improvements described above. The measured short time fluctuation of the differential absorption optical depth was reasonably close to that calculated using the carrier-to-noise ratio of the received signal.     

Fe3Si nanodots epitaxially grown on Si(111) substrates using ultrathin SiO2 film technique

Ultrahigh density (> 10¹² cm⁻²) Fe₃Si nanodots (NDs) are epitaxially grown on Si(111) substrates by codeposition of Fe and Si on the ultrathin SiO₂ films with ultrahigh density nanovoids. We used two kinds of methods for epitaxial growth: molecular beam epitaxy (MBE) and solid phase epitaxy. For MBE, low temperature (< 300 °C) growth of the Fe₃Si NDs is needed to suppress the interdiffusion between Fe atoms deposited on the surfaces and Si atoms in the substrate. These epitaxial NDs exhibited the ferromagnetism at low temperatures, which were expected in terms of the application to the magnetic memory device materials.     

Spin injection, transport, and read/write operation in spin-based MOSFET

We proposed a novel spin-based MOSFET “Spin-Transfer-torque-Switching MOSFET (STS-MOSFET)” that offers non-volatile memory and transistor functions with complementary metal-oxide-semiconductor (CMOS) compatibility, high endurance and fast write time using STS. The STS-MOSFETs with Heusler alloy (Co₂Fe₁Al_0.5Si_0.5) were prepared and reconfigurability of a novel spintronics-based MOSFET, STS-MOSFET, was successfully realized for the transport properties owing to reduction of the contact resistance in ferromagnetic metal/thin insulator tunnel barrier/Si junctions. The device showed magnetocurrent (MC) and write characteristics with the endurance of over 10⁵ cycles. It was also clarified that the read characteristic can be improved in terms of MC ratio, however, is deteriorated in terms of the mobility by choosing connection configurations of the source and the drain in the STS-MOSFETs.     

Study on methods of measuring frost crystal dimensions/structure and frost scraping force using a scanning probe microscope

Frosting on a cooling surface causes serious damage as well as economic losses. Therefore, it is necessary to clarify the mechanism of frosting on a cooling surface both scientifically and technologically. In addition, taking the size of frost crystals into account requires nano-micro-scale investigation. However, there have been few such studies. Thus, the focus of the present study is methods of measuring frost crystal dimensions/structure and frost scraping force in nano-micro-scale fields. In the present study, methods by which to measure frost crystal dimensions/structure, such as diameter, height, number of frost crystals, and interval between adjoining frost crystals, as well as the force required to scrape frost from a cooling surface using a scanning probe microscope (SPM) are proposed, and the effectiveness of these methods is investigated. With the exception of the frost crystal height, the feasibility of these measurements was demonstrated, and examples of the correlation of frost dimensions/structure and frost scraping force could are presented.     

Synthesis of zinc and zinc oxide nanoparticles from zinc electrode using plasma in liquid

Nanoparticles are synthesized efficiently from zinc electrode by microwave plasma in liquid. The nanoparticles synthesized from alcohol resulted in pure zinc particles in the shape of spheres or hexagonal cylinders with a production rate of 3.3 g/h, and energy consumption of 267 J/mg for 1 mg. Whereas the nanoparticles synthesized in pure water are composed of Zn and ZnO. The Zn reacts with water through heat or the passage of time to become ZnO, releasing hydrogen gas. An upper disk placed 1 mm away from the electrode along with the bubbles generated simultaneously with the plasma ignition plays a key role in the synthesis of nanoparticles.     

Vibration of a single microcapsule with a hard plastic shell in an acoustic standing wave field

Observation techniques for measuring the small vibration of a single microcapsule of tens of nanometers in an acoustic standing wave field are discussed. First, simultaneous optical observation of a microbubble vibration by two methods is investigated, using a high-speed video camera, which permits two-dimensional observation of the bubble vibration, and a laser Doppler vibrometer (LDV), which can observe small bubble vibration amplitudes at high frequency. Bubbles of tens of micrometers size were trapped at the antinode of an acoustic standing wave generated in an observational cell. Bubble vibration at 27 kHz could be observed and the experimental results for the two methods showed good agreement. The radial vibration of microcapsules with a hard plastic shell was observed using the LDV and the measurement of the capsule vibration with radial oscillation amplitude of tens of nanometers was successful. The acoustic radiation force acting on microcapsules in the acoustic standing wave was measured from the trapped position of the standing wave and the radial oscillation amplitude of the capsules was estimated from the theoretical equation of the acoustic radiation force, giving results in good agreement with the LDV measurements. The radial oscillation amplitude of a capsule was found to be proportional to the amplitude of the driving sound pressure. A larger expansion ratio was observed for capsules closer to the resonance condition under the same driving sound pressure and frequency.     

Stringiness morphology for crosslinked polyacrylic pressure-sensitive adhesives measured by peel testing with constant rate

To clarify the formation mechanism of front frame-type morphology, the stringiness of crosslinked random copolymers of poly(n-butyl acrylate-acrylic acid) during a 180° peel test with a constant tensile rate was examined for various crosslinker contents and rates using a quartz adherend. Cohesive failure occurred for lower crosslinker content and rate, whereas interfacial failure with sawtooth-type stringiness without a frame was observed for higher crosslinker content and rate. Front frame-type stringiness was formed at the boundary of cohesive and interfacial failures. To clarify the formation mechanism, observation was conducted from the start of peel test until the equilibrium state. The sawtooth-type stringiness with branches first formed at the tip. The adjoining branches were connected and the 2D frame was formed only on the adherend surface. The formed 2D frame developed toward the 3D walls and the front frame-type was then completed. This is caused by the surface tension that acts to restrain the increase in the surface area. However, the surface area of the front frame-type morphology was larger than the no frame-type. The larger absorption of peeling stress by the formation of this morphology is expected to contribute to peel strength improvement.     

Atom-selective imaging and mechanical atom manipulation using the non-contact atomic force microscope

We succeeded in distinguishing between oxygen and silicon atoms on an oxygen-adsorbed Si(111)7 x 7 surface, and also distinguished between silicon and tin atoms on Si(111)7 x 7-Sn intermixed and Si(111) square root(3) x square root(3)-Sn mosaic-phase surfaces using non-contact atomic force microscopy (NC-AFM) at room temperature. Atom species of individual atoms are specified from the number of each atom in NC-AFM images, the tip-sample distance dependence of NC-AFM images and/or the surface distribution of each atom. Further, based on the NC-AFM method but using soft nanoindentation, we achieved two kinds of mechanical vertical manipulation of individual atoms: removal of a selected Si adatom and deposition of a Si atom into a selected Si adatom vacancy on the Si(111)7 x 7 surface at 78 K. Here, we carefully and slowly indented a Si atom on top of a clean Si tip apex onto a predetermined Si adatom to remove the targeted Si adatom and onto a predetermined Si adatom vacancy to deposit a Si atom, i.e. to repair the targeted Si adatom vacancy. By combining the atom-selective imaging method with two kinds of mechanical atom manipulation, i.e. by picking up a selected atom species and by depositing that atom one by one at the assigned site, we hope to construct nanomaterials and nanodevices made from more than two kinds of atom species in the near future.     

Development of iron oxide sorbents for Hg removal from coal derived fuel gas: Sulfidation characteristics of iron oxide sorbents and activity for COS formation during Hg removal

The aim of this study is to develop a process for the removal of Hg⁰ using H₂S over iron oxides sorbents, which will be located just before the wet desulfurization unit and catalytic COS converter of a coal gasification system. It is necessary to understand the reactions between the iron oxide sorbent and other components of the fuel gas such as H₂S, CO, H₂, H₂O, etc. In this study, the sulfidation behavior and activity for COS formation during Hg⁰ removal from coal derived fuel gas over iron oxides prepared by precipitation and supported iron oxide (1 wt% Fe₂O₃/TiO₂) prepared by conventional impregnation were investigated. The iron oxide samples were dried at 110 °C (designated as Fe₂O₃-110) and calcined at 300 and 550 °C (Fe₂O₃-300 and Fe₂O₃-550). The sulfidation behavior of iron oxide sorbents in coal derived fuel gas was investigated by thermo-gravimetric analysis (TGA). COS formation during Hg⁰ removal over iron oxide sorbents was also investigated using a laboratory-scale fixed-bed reactor. It was seen that the Hg⁰ removal activity of the sorbents increased with the decrease of calcinations temperature of iron oxide and extent of sulfidation of the sorbents also increased with the decrease of calcination temperature. The presence of CO suppressed the weight gain of iron oxide due to sulfidation. COS was formed during the Hg⁰ removal experiments over Fe₂O₃-110. However, in the cases of calcined iron oxides (Fe₂O₃-300, Fe₂O₃-550) and 1 wt% Fe₂O₃/TiO₂, formation of COS was not observed but the Hg⁰ removal activity of 1 wt% Fe₂O₃/TiO₂ was high. Both FeS and FeS₂ were active for Hg⁰ removal in coal derived fuel gas without forming any COS.     

Activity enhancement of SnO2-doped Ga2O3–Al2O3 catalysts by coexisting H2O for the selective reduction of NO with propene

Catalytic reduction of NO by propene in the presence of oxygen was studied over SnO₂-doped Ga₂O₃–Al₂O₃ prepared by sol–gel method. Although SnO₂-doped Ga₂O₃–Al₂O₃ gave lower NO conversion than Ga₂O₃–Al₂O₃ in the absence of H₂O, the activity was enhanced considerably by the presence of H₂O and much higher than that of Ga₂O₃–Al₂O₃. The presence of SnO₂ and Ga₂O₃–Al₂O₃ species having intimate Ga–O–Al bondings was found to be essential for the promotional effect of H₂O. The promotional effect of H₂O was interpreted by the following two reasons. The first one is the removal of carbonaceous materials deposited on the catalyst surface by H₂O. The other is the selective inhibition by H₂O of the reaction steps resulting in propene oxidation to CO_x without reducing NO.