Relation between microstructure, properties and spark plasma sintering (SPS) parameters of pure ultrafine WC powder

A combined experimental/numerical methodology is developed to fully consolidate pure ultrafine WC powder under a current-control mode. Three applied currents, 1900, 2100 and 2700 A, and a constant pressure of 20 MPa were employed as process conditions. The developed spark plasma sintering (SPS) finite-element model includes a moving-mesh technique to account for the contact resistance change due to sintering shrinkage and punch sliding. The effects of the heating rate on the microstructure and hardness were investigated in detail along the sample radius from both experimental and modeling points of view. The maximum hardness (2700 HV10) was achieved for a current of 1900 A at the core sample, while the maximum densification was achieved for 2100 and 2700 A. A direct relationship between the compact microstructure and both the sintering temperature and the heating rate was established.     

Properties of Va metal-B films prepared by r.f.-sputtering

Ta_100-x B _x alloy films were prepared by r.f.-sputtering in the chemical composition range 45 x 77. Ta_100-x B _x (45 x 58) films consist of the amorphous phase, while the TaB₂ crystal phase was observed in Ta_100-x B _x (66 x 77) films. A remarkable preferred orientation with the (001) plane of TaB₂ parallel to the film surface was observed in Ta₃₄B₆₆. The d.c. electrical conductivity of Ta_100-x B _x (45 x 77) films decreases with increasing boron content in the range 6.7 × 10³ to 1.3 × 10^3–1 cm^–1. The micro-Vickers hardness of Ta_100-x B _x (45 x 77) films was in the range 2200 to 2600 kg mm^–2.     

Preparation of Co-N films by rf-sputtering

Co-N films in the wide compositional range can be prepared by reactive sputtering. Co-N sputtered films consist of one or two phases, such as CoN, Co₂N, Co₃N, Co₄N and -Co. Co₄N phase with a cubic unit cell is observed, and its lattice constant isa = 0.3586 nm. The preferred orientation is observed on the Co-N films, CoN (200) plane, Co₄N (1 1 1) plane and -Co (002) plane parallel to the film surface, respectively. Saturation magnetization _s of Co-N sputtered film decreases from 160 to 1.7 e.m.u. g^–1 with increasing content of N from 0 to 21.7 at%, and coercive force_I H _c is the range of 43 to 5000e at room temperature.     

Junction properties of polypyrrole containing a small amount of poly(ethylene oxide) with indium

A method to generate a porous region near the surface of a polymer is suggested. In this method the region near the surface is swollen by immersing the polymer for a short time in a solvent. Subsequently, the polymer is introduced in a nonsolvent (for the polymer) that is, however, miscible with the solvent. The formation of the porous region is a result of (1) the swelling accompanied by the disentanglement of the surface molecular chains, and the dissolution of some of them during the immersion in the solvent, and (2) the rapid extraction of the solvent from the swollen region by the nonsolvent. The porous surface provides a matrix into which a second incompatible monomer can be polymerized so that the two otherwise incompatible polymers can adhere to one another.     

Chemospecific ring-opening polymerization of α-methylenemacrolides

α-Methylenemacrolides having various groups, such as aromatic, ether, and amine, were enzymatically, anionically, and radically polymerized. The polymerization with the lipase catalyst successfully afforded polymers only through the ring-opening process, whereas the vinyl polymerizations selectively proceeded by using anionic and radical initiators. The polyesters obtained by the enzymatic polymerization have a polymerizable methacrylic methylene group in the main-chain, in addition to the aromatic and polar groups, and were further radically polymerized to quantitatively produce a cross-linked polymer gel.     

Charged ultrafiltration membrane for permeation of proteins

Polyacrylonitrile-g-poly(N,N-dimethylaminoethyl methacrylate) was synthesized photochemically and quaternized. The positively charged membranes made from the quaternized graftcopolymer showed high ultrafiltration rate for water by adding poly(vinyl alcohol) to casting solution and washing it out after the casting. In buffered saline solution, the permeability of the membranes was very small at pH below isoelectric point of albumin but increased markedly at higher pH. On the other hand, the permeability for γ-globulin was very small and did not show any pH dependence.     

Observation of single-walled carbon nanotubes by photoemission microscopy

Single-walled carbon nanotube networks grown on SiO₂ pillars were studied by means of scanning photoemission microscopy. The individual nanotubes or nanotube bundles growing from the pillar tops were observed in C 1s images. Band bending near catalytic Fe/nanotube contacts in an end-bonded configuration was studied by measuring C 1s spectra along the tube axes. Within our experimental resolution, no band bending was observed. This implies that the depletion width is less than the spatial resolution of the scanning photoemission microscope (90 nm) or that the amount of the band bending is less than 0.1 eV.     

Anodic Dissolution of Uranium Mononitride in Lithium Chloride-Potassium Chloride Eutectic Melt

Uranium-plutonium nitride is a candidate fuel for fast reactors, but its major drawback is ¹⁴C formation from natural nitrogen. One would probably have to use highly ¹⁵N-enriched nitrogen. A pyrochemical process with molten-salt electroreflning has been proposed as a means to increase the nuclear proliferation resistance of the fuel cycle. Molten-salt electroreflning could also be applied to nitride fuels to make possible the recycling of ¹⁵N. The anodic dissolution behavior of UN in LiCI-KCI melt was studied to provide the basis for a feasibility study of electroreflning of irradiated nitride fuels.     

Selective O-methylation of phenol with dimethyl carbonate over X-zeolites

The O-methylation of phenol with dimethyl carbonate proceeds selectively in the vapor phase over alkali ion exchanged X-zeolites. Thus, a 76% yield of anisole was obtained with a 93% selectivity over NaX at 553 K. The participation of basic sites in the O-methylation is suggested.     

Evaluation for distance learning scheme on distributed multiple server system

A distributed multiple server system is designed and implemented with Web-DB based services for distance learning as well as emergency communication. The system has employed multiple servers located in a distributed campus network environment. Each server of the system has multi-core processors. With so-called “server virtualization” technology, some programs are executed in parallel (on the virtual servers) so that such a system can efficiently perform several functions. For example, two or more application services can be performed simultaneously as “cloud services” on the whole system. The system can provide distance learning scheme for educational tool, at the same time it can also support Web-based surveillance facilities for emergency contact. With qualitative and quantitative approach, trial evaluation of system has been performed in some classrooms of distributed campus. And users can obtain some good results from the above evaluation.