Tribological properties of asperity arrays coated with self-assembled monolayers

The effects of a self-assembled monolayer (SAM) coating on the friction and pull-off forces were determined by using two-dimensional asperity arrays on silicon wafers. The arrays were coated with SAM composed of one of five different alkylchlorsilanes. First, two-dimensional asperity arrays were created by using a focussed ion beam (FIB) system to mill patterns on silicon plates. Each silicon plate had different patterns of equally spaced asperities. Each pattern (5 × 5 μm²) had a different radius of curvature of the asperity peaks, ranging from about 200 to 2500 nm. Then, each silicon plate was immersed in a solution of a different alkylchlorsilane in hexane (either hexyltrichlorosilane, octyltrichlorosilane, dodecyltrichlorosilane, tetradecyltrichlorosilane, or octadecyltrichlorosilane), thus coating the asperity arrays with SAM. The friction and pull-off forces on the SAM-coated arrays were measured by using an atomic force microscope (AFM) that had a square flat probe. The pull-off force for SAM-coated silicon was roughly proportional to the radius of curvature of the asperity peaks. The magnitude of the pull-off force corresponded approximately to the capillary force calculated by using the contact angle of water on the surface of SAM. The friction coefficient correlated with the inverse of the alkyl-chain length of the SAM.     

Discharge behaviors and jet profiles during electrospinning of poly(vinyl alcohol)

Relations between beads formation and jet profiles, and beads formation and electric discharge during electrospinning were investigated by changing sample parameters and spinning conditions. The jet profiles were obtained as a function of the position along the spinning line by using photographs. As the molecular weight or concentration increased, the elongational viscosity of jet at the onset of bending instability was increased, and beads formation was suppressed. In addition, beads formation was enhanced with increasing voltage. The electric discharge spark from the apex of cone was observed by using image intensified high‐speed camera. It was found that the beads were also formed easily when the electric discharge generated. POLYM. ENG. SCI., 50:1788–1796, 2010. © 2010 Society of Plastics Engineers     

High‐performance V/f control of PMSM using state feedback control based on n–t coordinate system

This paper proposes a new V/f control method for permanent magnetic synchronous motors (PMSMs) without a position sensor. The proposed method uses state feedback control based on an n–t coordinate system, and controls rotational speed and the voltage amplitude. The t‐axis is a tangent line of a constant voltage ellipse, and the n‐axis is a normal line of the ellipse. The t‐axis current is utilized to place the poles of the transfer function at the desired position at low‐speed and high‐speed conditions. The effectiveness of the proposed method was verified by simulation and experimental results.     

Design of band elimination filter for PMSM vector control operable in overmodulation region of inverter

This paper proposes a filter design for improving the control performance of the current control system of permanent magnet synchronous motors (PMSMs) using the overmodulation region of an inverter. The control performance of a vector control system for PMSMs using the overmodulation region of an inverter can be improved by suppressing harmonic components that are generated in this region. This paper utilizes band elimination filter (BEF) to eliminate harmonic components; however, unsuitable BEF setting leads to generation of large current oscillation at the resonant frequency of current feedback loop with BEF. In order to deal with these problems, the proposed filter design focuses on gain setting at the cutoff frequency of BEF. The proposed filter design can prevent the generation of current oscillation at the resonant frequency of the system, and can improve current control performance without complex adjustments. Simulations and experiments are carried out to show the effectiveness of the proposed BEF setting.     

Feasibility study of decay heat uncertainty reduction using nuclear data adjustment method with experimental data

The accurate prediction of the decay heat is essential, especially for nuclear power plant safety purposes. However, it is known that the decay heat predicted by nuclear fuel burn-up calculations is uncertain because of uncertainty of nuclear data employed in the calculations. If the decay heat uncertainty can be reduced, the safety margin of the predicted decay heat can also be reduced, and feasible design ranges of various types of equipments related to the decay heat can be extended. In the present study, we use the nuclear data adjustment method for the decay heat uncertainty reduction with several types of the experimental data. As a result, we clarify that the decay heat uncertainty with short- and long-term cooling periods can be reduced by this method with appropriate experimental data.     

Application of bis(fluorosulfonyl)imide-based ionic liquid electrolyte to silicon-nickel-carbon composite anode for lithium-ion batteries

An ionic liquid electrolyte containing bis(fluorosulfonyl)imide (FSI) anion without any solvent is applied to a silicon-nickel-carbon (Si-Ni-carbon) composite anode for rechargeable lithium (Li)-ion batteries. The FSI-based ionic liquid electrolyte successfully provides a stable, reversible capacity for the Si-Ni-carbon anode, which is comparable to the performance observed in a typical commercialized solvent-based electrolyte, while a common ionic liquid electrolyte containing bis(trifluoromethanesulfonyl)imide (TFSI) anion without FSI presents no reversible capacity to the anode at all. Ac impedance analysis reveals that the FSI-based electrolyte provides very low interfacial and charge-transfer resistances at the Si-based composite anode, even when compared to the corresponding resistances observed in a typical solvent-based electrolyte. Galvanostatic cycling of the Si-based composite anode in the FSI-based electrolyte with a charge limitation of 800 mAh g⁻¹ is stable and provides a discharge capacity of 790 mAh g⁻¹ at the 50th cycle, corresponding to a cycle efficiency of 98.8%.     

Reversible polycolour change of viologens from violet through transparent to white

The electrochromic properties of 1,1′-dibenzyl-4,4′-bipyridinium and 1,1′-diheptyl-4,4′-bipyridinium were investigated in the presence of MBr (M = Li⁺, Na⁺, and K⁺). The cyclic voltammograms of these viologens showed a white-coloured state in addition to the usual violet one-electron reduction state and the colourless divalent state. Chemical analyses (FT-IR and XPS spectra) of the white film and some control experiments with different supporting electrolytes, MX (X = Cl⁻ and I⁻), revealed that the viologens formed water-insoluble ion pairs with tribromide generated by the electrooxidation of monobromide to produce a white film. The film was reversibly decolourized electrochemically to the initial transparent state, providing the polyelectrochromism using the simple viologen/MBr systems. The colouration efficiencies for the violet and the white-coloured states were 170 cm²/C and 104 cm²/C, respectively.