Enhancing cardiac parasympathetic nervous activity using a posture respiration ambient biofeedback system: a pilot study

A respiration–posture feedback system was developed to control breathing involuntarily. A small air chamber placed under a subject’s back deflates and inflates to make a subject’s upper body move vertically while lying on a bed. By regulating the deflation/inflation of the air chamber in synchronization with actual respiration, the subject’s respiration was successfully lengthened and deepened. The modulation of the respiration acted as a physiological sedative for the subject as the heart rate variability index suggested that the subject’s parasympathetic nervous system activity was enhanced.     

Colloidal Consolidation of Ceramic Nanoparticles by Pressure Filtration

The applied pressure and suspension height during consolidation of an aqueous suspension of nanometer-sized particles (24 nm hydroxyapatite, 30 nm SiC, 68 nm 8 mol% yttria-stabilized zirconia, 150 nm Al₂O₃, and 800 nm SiC) were continuously recorded using a pressure filtration apparatus. The packing density decreased when the particle size was less than 70 nm. The final packing density of 150−800 nm particles at 19 MPa was strongly influenced by the surface charge. However, surface charge does not affect the packing density of particles less than 70 nm. The ratio of the energy applied to two particles during consolidation to the interaction energy between two particles in a suspension was correlated to the packing density. The low packing density of 20−30 nm particles was improved by steric stabilization. The estimated thickness of the dispersant layer adsorbed on the particle surfaces was less than 1 nm and nearly independent of the molecular weight of the dispersants. When the applied pressure was released, the height of the consolidated cake increased because of the release of the elastic strain stored in the dispersant layer.     

Mechanical Properties of Hot Isostatically Pressed Zirconia-Toughened Alumina Ceramics Prepared from Coprecipitated Powders

Amorphous Al₂O₃–ZrO₂ composite powders with 5–30 mol% ZrO₂ have been prepared by adding aqueous ammonia to the mixed solution of aqueous aluminum sulfate and zirconium alkoxide containing 2-propanol. Simultaneous crystallization of γ-Al₂O₃ and t -ZrO₂ occurs at 870°–980°C. The γ-Al₂O₃ transforms to α-Al₂O₃ at 1160°–1220°C. Hot isostatic pressing has been performed for 1 h at 1400°C under 196 MPa using α-Al₂O₃– t -ZrO₂ composite powders. Dense ZrO₂-toughened Al₂O₃ (ZTA) ceramics with homogeneous-dispersed ZrO₂ particles show excellent mechanical properties. The toughening mechanism is discussed. The microstructures and t / m ratios of ZTA are examined, with emphasis on the relation between strength and fracture toughness.     

Iodine-initiated,solid-state copolymerization of tetraoxane with 1,3-dioxolane in the presence of methylal. I. Fundamental study on beaker-scale copolymerization

The iodine-initiated, solid-state copolymerization of tetraoxane with 1,3-dioxolane in the presence of methylal has been studied on a beaker scale. It was found that tetraoxane can be easily copolymerized with 1,3-dioxolane by a small amount of iodine as initiator and gives oxymethylene copolymer with excellent thermal stability in a high yield. The copolymerization was largely influenced by the concentrations of iodine, 1,3-dioxolane, and methylal, i.e., the polymerization rate increased with increase not only in iodine but also in 1,3-dioxolane, and the thermal stability and the molecular weight of the copolymer were mainly affected by 1,3-dioxolane and methylal concentration, respectively.     

Novel super fast response vertical alignment‐liquid crystal display with extremely wide temperature range

We have developed a novel super fast response (SFR) thin‐film transistor liquid crystal display (TFT‐LCD) with an extremely wide temperature range. Nematic liquid crystal molecules with positive dielectric anisotropy are vertically aligned initially. Any gray‐to‐gray response is forcibly controlled by applying an electric field. Response times of the SFR TFT‐LCD are over several times shorter than those of conventional LCDs such as vertical alignment or in‐plane switching LCDs.     

Application of accelerators for the research and development of scintillators

We introduce experimental systems which use accelerators to evaluate scintillation properties such as scintillation intensity, wavelength, and lifetime. A single crystal of good optical quality is often unavailable during early stages in the research and development (R&D) of new scintillator materials. Because of their beams' high excitation power and/or low penetration depth, accelerators facilitate estimation of the properties of early samples which may only be available as powders, thin films, and very small crystals. We constructed a scintillation spectrum measurement system that uses a Van de Graaff accelerator and an optical multichannel analyzer to estimate the relative scintillation intensity. In addition, we constructed a scintillation time profile measurement system that uses an electron linear accelerator and a femtosecond streak camera or a microchannel plate photomultiplier tube followed by a digital oscilloscope to determine the scintillation lifetimes. The time resolution is approximately 10 ps. The scintillation spectra or time profiles can be obtained in a significantly shorter acquisition time in comparison with that required by conventional measuring systems. The advantages of the systems described in this study can significantly promote the R&D of novel scintillator materials.     

Tribological properties of asperity arrays coated with self-assembled monolayers

The effects of a self-assembled monolayer (SAM) coating on the friction and pull-off forces were determined by using two-dimensional asperity arrays on silicon wafers. The arrays were coated with SAM composed of one of five different alkylchlorsilanes. First, two-dimensional asperity arrays were created by using a focussed ion beam (FIB) system to mill patterns on silicon plates. Each silicon plate had different patterns of equally spaced asperities. Each pattern (5 × 5 μm²) had a different radius of curvature of the asperity peaks, ranging from about 200 to 2500 nm. Then, each silicon plate was immersed in a solution of a different alkylchlorsilane in hexane (either hexyltrichlorosilane, octyltrichlorosilane, dodecyltrichlorosilane, tetradecyltrichlorosilane, or octadecyltrichlorosilane), thus coating the asperity arrays with SAM. The friction and pull-off forces on the SAM-coated arrays were measured by using an atomic force microscope (AFM) that had a square flat probe. The pull-off force for SAM-coated silicon was roughly proportional to the radius of curvature of the asperity peaks. The magnitude of the pull-off force corresponded approximately to the capillary force calculated by using the contact angle of water on the surface of SAM. The friction coefficient correlated with the inverse of the alkyl-chain length of the SAM.     

Discharge behaviors and jet profiles during electrospinning of poly(vinyl alcohol)

Relations between beads formation and jet profiles, and beads formation and electric discharge during electrospinning were investigated by changing sample parameters and spinning conditions. The jet profiles were obtained as a function of the position along the spinning line by using photographs. As the molecular weight or concentration increased, the elongational viscosity of jet at the onset of bending instability was increased, and beads formation was suppressed. In addition, beads formation was enhanced with increasing voltage. The electric discharge spark from the apex of cone was observed by using image intensified high‐speed camera. It was found that the beads were also formed easily when the electric discharge generated. POLYM. ENG. SCI., 50:1788–1796, 2010. © 2010 Society of Plastics Engineers