The effect of inorganic additives on the formation,composition, and combustion of cellulosic char

At temperature above 300°C the glycosyl units of cellulose are simultaneously depolymerized to a tar and decomposed to a char by evolution of H₂O, CO, and CO₂. When the glycosyl units are depleted, a stable char is formed containing about 30% aliphatic and 70% aromatic components. The aliphatic component is formed first, but on further heating is converted to polycyclic aromatic structures. The chars formed at lower temperatures are more combustible because the aliphatic component of the char is highly pyrophoric and is oxidized almost at the same temperature at which it is formed (～360°C). The aromatic component, however, is less reactive and is oxidized at ～520°C. Consequently, the chars formed at higher temperatures are less combustible. It has been shown that (NH₄)₂HPO₄, which is a well-known flame retardant and smoldering inhibitor, lowers the pyrolysis temperature and increases the char yield by accelerating the decomposition reactions. This affects the composition of the intermediate chars but the final products have about the same composition irrespective of additives. (NH₄)₂HPO₄ also lowers the rate of oxidation of the aromatic component and the corresponding heat release. NaCl, which is an enhancer of smoldering combustion, has a slight stabilizing effect on pyrolysis of cellulose. It lowers the oxidation temperature of the aromatic component and dramatically increases its rate. The corresponding heat release is also increased due to complete oxidation to CO₂. The rate of oxidation calculated from the dynamic thermal analysis data is more than tripled by NaCl and significantly reduced by (NH₄)₂HPO₄.     

Effect of vanadium and chromium on the microstructural features of V–Cr–Mn–Ni spheroidal carbide cast irons

The objective of this investigation is to study the influence of vanadium（5.0wt%–10.0wt%） and chromium（0–9.0wt%） on the microstructure and hardness of Cr-V-Mn-Ni white cast irons with spheroidal vanadium carbides. The alloys＇ microstructural features are presented and discussed with regard to the distribution of phase elements. The structural constituents of the alloys are spheroidal VC, proeutectoid cementite, ledeburite eutectic, rosette-shaped carbide eutectic（based on M7C3）, pearlite, martensite, and austenite. Their combinations and area fraction（AF） ratios are reported to be influenced by the alloys＇ chemical composition. Spheroidized VC particles are found to be sites for the nucleation of carbide eutectics. Cr and V are shown to substitute each other in the VC and M7C3 carbides, respectively. Chromium alloying leads to the formation of a eutectic（γ-Fe ＋ М7С3）, preventing the appearance of proeutectoid cementite in the structure. Vanadium and chromium are revealed to increase the total carbide fraction and the amount of austenite in the matrix. Cr is observed to play a key role in controlling the metallic matrix microstructure.     

Spatial distribution of silica fillers in phase-separated rubber blends investigated by three-dimensional elemental mapping

The distribution of nano-sized silica in binary rubber blends is characterized by scanning transmission electron microscopy (STEM) tomography combined with energy dispersive X-ray spectrometry (EDX). 3D distribution of silica is visualized by STEM-EDX tomography with the tilt-series of silicon elemental maps, while the phase-separated morphologies of polyisoprene rubber (IR) and styrene-butadiene rubber (SBR) are visualized by STEM-tomography in high-angle-annular-dark field (HAADF) mode. The combination of STEM-EDX and STEM-HAADF tomography enables us to determine the distribution of silica between the two rubber phases quantitatively even with high contents of silica up to 70 phr (weight parts per hundred rubber). It is found that silica is preferentially distributed in the SBR phase, but it is also distributed in the IR phase when the IR fraction in the total rubber components is higher than 40 wt%. The preferential distribution of silica in the SBR phase improves the dispersion of the IR domains. This is the first use of this technique for a multicomponent polymer system, showing the advantage to characterize the complicated multicomponent polymer composite morphologies.     

Development of flexible displays using back‐channel‐etched In–Sn–Zn–O thin‐film transistors and air‐stable inverted organic light‐emitting diodes

We developed flexible displays using back‐channel‐etched In–Sn–Zn–O (ITZO) thin‐film transistors (TFTs) and air‐stable inverted organic light‐emitting diodes (iOLEDs). The TFTs fabricated on a polyimide film exhibited high mobility (32.9 cm²/Vs) and stability by utilization of a solution‐processed organic passivation layer. ITZO was also used as an electron injection layer (EIL) in the iOLEDs instead of conventional air‐sensitive materials. The iOLED with ITZO as an EIL exhibited higher efficiency and a lower driving voltage than that of conventional iOLEDs. Our approach of the simultaneous formation of ITZO film as both of a channel layer in TFTs and of an EIL in iOLEDs offers simple fabrication process.     

Reliability and mechanical durability tests of flexible OLED with ALD coating

To improve the reliability and mechanical durability of a flexible organic light‐emitting diode display, the entire flexible display is coated with an aluminum oxide film by atomic layer deposition (ALD). Because the step coverage of ALD is excellent, the AlO_x film was deposited not only on the front and back surfaces but also on the side surfaces of the display. A high‐temperature and high‐humidity preservation test, repetitive bending tests, and a pencil hardness test were conducted on the flexible display with ALD‐AlO_x coating. The display survived 500 h of a 65°C, 95% preservation test, endured a 100,000‐time repetitive bending test with a curvature radius of 4 mm, and was found to have a pencil hardness of 4H.     

Computational design of iris folding patterns

Computational Visual Media - Iris folding is an art-form consisting of layered strips of paper, forming a spiral pattern behind an aperture, which can be used to make cards and gift tags. This...     

Fabrication of 5.8‐in. OTFT‐driven flexible color AMOLED display using dual protection scheme for organic semiconductor patterning

Abstract— A 5.8‐in. wide‐QQVGA flexible color active‐matrix organic light‐emitting‐diode (AMOLED) display consisting of organic thin‐film transistors (OTFTs) and phosphorescent OLEDs was fabricated on a plastic film. To reduce the operating voltage of the OTFTs, Ta₂O₅ with a high dielectric constant was employed as a gate insulator. Pentacene was used for the semiconductor layer of the OTFTs. This layer was patterned by photolithography and dry‐etched using a dual protection layer of poly p‐xylylene and SiO₂ film. Uniform transistor performance was achieved in the OTFT backplane with QQVGA pixels. The RGB emission layers of the pixels were formed by vacuum deposition of phosphorescent small molecules. The resulting display could clearly show color moving images even when it was bent and operated at a low driving voltage (below 15 V).     

Construction of a robot control system which understands a voice and pointing actions

This research was aimed at making a robot that can go and get an object designated by the user. We produced a robot control system that uses pointing and voice control. This control system is composed of two systems. One system is the object instruction system that uses pointing, and the other is the object instruction system that uses voice. The approximate position of a designated object is recognized by the object instruction system that uses pointing, and information about the object and instructions about the operation are conveyed by the object instruction system that uses voice. This time, the object instruction system that uses pointing has been designed and verified as the first step. A calculation resource to calculate the approximate position of the designated object is obtained when the user points directly at the object. A robot can be moved around a designated object by using this system. The object instruction system that uses voice will be constructed in future work.     

Fourier-transform speckle profilometry: three-dimensional shape measurements of diffuse objects with large height steps and/or spatially isolated surfaces

An interferometric technique for automated profilometry of diffuse objects has been proposed. It is based on the Fourier-fringe analysis of spatiotemporal specklegrams produced by a wavelength-shift interferometer with a laser diode as a frequency-tunable light source. Unlike conventional moiré techniques the proposed technique permits the objects to have discontinuous height steps and/or surfaces spatially isolated from one another. Experimental results are presented that demonstrate the validity of the principle.