Effects of Cooling Rate and Component on the Microstructure and Mechanical Properties of Mg–Zn–Y Alloys

The microstructure and mechanical properties of Mg–6Zn–1Y and Mg–6Zn–3Y(wt%) alloys under different cooling rates were investigated. The results show that the second dendrite arm spacing(SDAS) of Mg–6Zn–1Y and Mg–6Zn–3Y is reduced by 32 and 30% with increasing cooling rates(Rc) from 10.2 to 23 K/s, which can be predicted using a empirical model of SDAS=68 R 0:45:45cand SDAS=73 R 0c, respectively. The compressive strength of both alloys increases with increasing the cooling rate, which is attributed to the increase of volume fraction(Vf) of secondary phases under high cooling rate. The interaction of the cooling rate and component with SDAS has been theoretically analyzed using interdependence theory.     

Structural,morphological, dielectric and magnetic properties of Zn-Zr co-doping yttrium iron garnet

In this study, yttrium iron garnet co-doped with Zn and Zr atoms with a chemical formula Y₃Zn_xZr_xFe_(5−2x)O₁₂ (x = 0.0-0.3) has been successfully prepared by the solid-state reaction method. The effects of doping concentration on the microstructure, crystal structure, magnetic properties, and dielectric properties of Y₃Zn_xZr_xFe_(5−2x)O₁₂ were investigated. The microstructure analysis indicates that co-doping of YIG with Zn and Zr can effectively reduce the grain size of the ceramic. The crystal structure results reveal that the doping concentration of Zn–Zr has substantial influence on the lattice parameters of YIG, such as, increases the lattice constant, crystal cell size, and interplanar spacing. However, the second phase of ZrO₂ appears once x ≥ 0.15. Additionally, the dielectric properties of YIG ferrite can be regulated using this Zn–Zr co-doping method. Zn–Zr co-doping can improve the dielectric stability and reduce the dielectric loss at high temperature. The magnetization measurement shows that the saturation magnetization is stabilized at x < 0.15, and the magnetic loss is decreased with the increase in the doping concentration. Overall, the findings show that the ceramic with x = 0.1 exhibits better properties included high saturation magnetization (24.607 emu/g), low magnetic loss (0.0025 @ 1 MHz), and relatively low dielectric loss (496 @ 400°C).     

Single-Crystalline TiO2(B) Nanobelts with Unusual Large Exposed {100} Facets and Enhanced Li-Storage Capacity

The {100} facet of single-crystalline TiO₂(B) is an ideal platform for inserting Li ions, but it is hard to be obtained due to its high surface energy. Here, the single-crystalline TiO₂(B) nanobelts from H₂Ti₃O₇ with nearly 70% {100} facets exposed are synthesized, which significantly enhances Li-storage capacity. The first-principle calculations demonstrate an ab in-plane 2D diffusion through the exposed {100} facets. As a consequence, the nanobelts can significantly accommodate Li ions in LiTiO₂ formula with specific capacity up to 335 mAh g⁻¹, which is in good agreement with the electrochemical characterizations. Coating with conductive and protective poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate), the cut-off discharge voltage is as low as 0.5 V, leading to a capacity of 160.7 mAh g⁻¹ after 1500 cycles with a retention rate of 66% at 1C. This work provides a practical strategy to increase the Li-ion capacity and cycle stability by tailoring the crystal orientation and nanostructures.     

Sparse non-convex Lp regularization for cone-beam X-ray luminescence computed tomography

Cone-beam X-ray luminescence computed tomography (CB-XLCT) is an attractive hybrid imaging modality, and it has the potential of monitoring the metabolic processes of nanophosphors-based drugs in vivo. However, the XLCT imaging suffers from a severe ill-posed problem. In this work, a sparse nonconvex L_p (0?p?L₁ regularization. Further, an iteratively reweighted split augmented lagrangian shrinkage algorithm (IRW_SALSA-L_p) was proposed to efficiently solve the non-convex L_p (0?p?p-values (1/16, 1/8, 1/4, 3/8, 1/2, 5/8, 3/4, 7/8) in both 3D digital mouse experiments and in vivo experiments. The results demonstrate that the proposed non-convex methods outperform L₂ and L₁ regularization in accurately recovering sparse targets in CB-XLCT. And among all the non-convex p-values, our L_p(1/4?p?相似文献   

Computational Analysis of the Solid-State and Solvation Properties of Carbamazepine in Relation to its Polymorphism

The solvent-dependent polymorphism of the active pharmaceutical ingredient (API) carbamazepine is interpreted from calculations of the solid-state and API-solvent intermolecular interactions. These simulations suggested that apolar solute-solute interactions could be disrupted by apolar solvents. In contrast, the polar solute-solute interactions were found to be easily disrupted by polar and protic solvents. This is consistent with experimental observations that the crystallization of the metastable form II is more dominant in apolar solvents. The Mercury program remains the gold standard in terms of usability; however, further expansion into more complex simulation techniques could make this package of even greater use in pharmaceutical manufacturing workflows.     

Dynamics and workspace analysis of a multi-robot collaborative towing system with floating base

Journal of Mechanical Science and Technology - A multi-robot collaborative towing system fixed on floating base for high load marine work was established in this paper, and its dynamics and...     

PDC钻头水力结构优化设计研究

在PDC钻头工作过程中，钻井液对钻头体表面的冲洗、冷却和润滑是保证钻头正常工作的一个非常重要的条件。对PDC钻头而言，水力结构（主要是中心水眼和冠部水道）设计的重要性尤其突出。以前,对钻头水力系统研究只能通过实验的方法进行,研究周期长、成本高、结构调整不方便，而数值模拟的方法在几年前还不成熟，甚至静态的复杂结构流场问题基本无法解决。为此，在提出PDC钻头水力结构优化设计原则的基础上，对PDC钻头的三维流场进行了数值模拟。模拟中考虑了钻头的喷嘴布置位置、直径、数量以及切削齿对流场的影响。计算结果表明，原设计在喷嘴布置位置和喷射角度上存在不足，以此为基础进行了水力结构的优化设计。文中的研究成果成功地应用在新型钻头水力结构的设计中，研究方法为PDC钻头水力结构优化分析奠定了理论基础。