双波长Nd：YAG脉冲激光器的实验研究

根据多波长同时振荡条件，我们建立了大能量１０６４ｎｍ和１３１８ｎｍ同时运转的双波长脉冲Ｎｄ：ＹＡＧ激光器。得到了１０６４ｎｍ和１３１８ｎｍ的激光输出能量分别为０．５９４Ｊ和０．８６１Ｊ，效率分别为０．３１％和０．４５％。实验结果说明了该双波长激光器有较好的时间和空间重选性。     

稀土在搪瓷面釉上应用的研究

采用稀土氧化物和无机化合物的复合物（不简称ＲＩ－复合物）作为搪瓷釉浆悬浮剂，使之全部或大部分代替粘土，进行了一系列试验，已获得成功，突破了长期来搪瓷工业离不开粘土的传统工艺，并实现了工业化生产。     

镀镍云母导电复合材料的研究

对云母粒子化学镀镍及以LDPE为基材,镀镍云母粒子为填料制备的导电复合材料进行研究。认为此种导电复合材料只有质量轻、强度大及良好的导电等性能。     

CALCULATION ON TWO-PHASE FLOW TRANSIENTS AND THEIR EXPERIMENTAL RESEARCH

From basic equations of gas-liquid, solid-liquid, solid-gas two-phase flow, the calculating method on flow transients of two-phase flow is developed by means of characteristic method. As one example, a gas-liquid flow transient is calculated and it agrees well with the experimental result. It is shown that the method is satisfactory for engineering demand.     

Comparisons of PWM and one-cycle control for power amplifier with multilevel converter

Based on the concepts of cascade multilevel converters and one-cycle technique, comparisons are conducted to characterize the distortion of the pulsewidth modulation (PWM) and one-cycle control methods that were applied to converters. Simulation results for the different control schemes are obtained in PSIM software initially to see the effect of one-cycle control different from that of PWM control. Through the comparisons, the advantages and disadvantages are identified for each method. The one-cycle scheme is better than PWM control in reducing undesirable harmonics and tracing dynamic waveforms. Simulation and experimental results are also provided to verify the conclusions.     

用投影预变换提高自适应波束形成的稳健性

在快拍数较少和（或）存在系统误差时，自适应波束形成的性能会变差，特别是会引起方向图副瓣电平升高——波束畸变。本文提出的投影变换法利用干扰方向的初略估计，在未精确预知阵列流形的条件下，可以显著改善自适应方向图的副瓣性能，并提高自适应算法的收敛性，计算机仿真结果验证了这一优点。     

Formation mechanism of bainitic ferrite and carbide

Superledges on the broad faces of bainitic ferrite plates have been observed with transmission electron microscope (TEM). The observed superledges, ranging from less than 1 to 24 nm in height, are imaged in three dimension by way of tilt operation under TEM. Also, an array of smaller superledges are observed to pile up in front of a secondary phase. Pileup of superledges in front of a barrier is indicative of the mobility of an individual superledge. The precipitation of carbide associated with bainitic ferrite is also studied. It is observed that a carbide of a wedgelike shape may exist in front of a superledge with its tip(i.e., thinner end) penetrating the austenite and its root (the other end) originating at α:γ boundary. This condition indicates that the observed carbides may nucleate at the austenite side of α:γ phase boundary and grow toward austenite matrix. This article is based on a presentation made at the Pacific Rim Conference on the “Roles of Shear and Diffusion in the Formation of Plate-Shaped Transformation Products,” held December 18-22, 1992, in Kona, Hawaii, under the auspices of ASM INTERNATIONAL’S Phase Transformations Committee.     

结构陶瓷的空蚀性研究

利用转盘装置测量了ZrO2、Si3N4和Al2O3／Ti(NC)等陶瓷材料受到水的空蚀破坏的体积损失,通过SEM观察和XRD分析,探讨了微观结构和抗空蚀性能的关系。     

一个面积和功耗优化且适用于10/100 Base-T以太网的CMOS时钟恢复电路

提出了一个新的用于10 / 10 0 Base- T以太网中面积和功耗优化的时钟恢复电路.它采用双环路的结构,加快了锁相环路的捕获和跟踪速度;采用复用的方式,通过选择信号控制电路可分别在10 Mbps或10 0 Mbps模式下独立工作且能方便地实现模式间的互换,与采用两个独立的CDR电路相比节省了一半的面积;同时,电路中采用一般的延迟单元来取代DL L,并能保证环路性能不随工艺温度等条件引起的延迟单元、延迟时间的变化而变化,从而节省了功耗.Hspice模拟结果显示,在Vdd=2 .5 V时,10 0 Mbps模式下电路的功耗约为75 m W,稳态相差为0 .3 ns;10 Mbps模式时电路功耗为5 8m W     

我国塑料机械工业概况与发展

介绍了我国2001年塑料机械工业的生产状况，通过大量翔实的数据对我国注射机、挤出机和吹塑机三大产品的生产技术、经济技术指标及进出口市场状况进行了分析。