Ti-23Al-14Nb-3V合金氩弧焊接头的显微组织及其力学性能

研究了预热对Ｔｉ－２３Ａｌ－１４Ｎｂ－３Ｖ合金焊接性，特别是对消除氩弧焊冷裂纹的作用以及对接头显微组织和力学性能的影响。结果表明，焊前预热可有效降低该合金的冷裂倾向。经预热处理后，焊缝区的结晶层状线消失，热影响区的硬度峰得到缓和，整个焊缝的显微硬度分布趋于均匀，但焊缝区的枝晶发生粗化，热影响区有所扩大。焊件接头的拉伸试验表明，预热可使焊缝区的接头强度系数增加，但无论预热与否，接头强度均低于母材强度，且不显示宏观塑性。     

Flammability and thermal stability studies of ABS/Montmorillonite nanocomposite

Acrylonitrile–butadiene–styrene (ABS)/montmorillonite nanocomposites have been prepared using a direct melt intercalation technique by blending ABS and organophilic clay of two different particle sizes: OMTa (5 µm) and OMTb (38 µm). Their structure and flammability properties were characterized by X‐ray diffraction, high resolution electronic microscopy (HREM), thermogravimetric analysis (TGA) and cone calorimeter experiments. The results of HREM showed that ABS/5 wt% OMTa nanocomposite was a kind of intercalated–delaminated structure, while ABS/5 wt% OMTb nanocomposite was mainly an intercalated structure. The nanocomposites showed a lower heat release rate peak and higher thermal stability than the original ABS by TGA and cone calorimeter experiments. Also, the intercalated nanocomposite was more effective than an exfoliated–intercalated nanocomposite in fire retardancy. Copyright © 2003 Society of Chemical Industry     

Joint coding-precoding with low-complexity turbo-decoding

We combine error-control coding with linear precoding (LP) for flat-fading channels, as well as for wireless orthogonal frequency-division multiplexing transmissions through frequency-selective fading channels. The performance is analyzed and compared with the corresponding error-control-coded system without precoding. By wedding LP with conventional error-control coding, the diversity order becomes equal to the error-control code's minimum Hamming distance times the precoder size. We also derive a low-complexity turbo-decoding algorithm for joint coded-precoded transmissions. We analyze the decoding complexity and compare it with an error-control-coded system without LP. Extensive simulations with convolutional and turbo codes for HiperLan/2 channels support the analysis and demonstrate superior performance of the proposed system.     

锌钾硼对甜菜产质量效应及最佳施肥措施的研究

本文利用最优回归设计“310”方案,研究了黑土地甜菜 Zn、K_2O、B的效果及合理施用问题。得出甜菜块根产量、含糖、产糖量、灰分 K 和有害 N 与 ZnK_2O、B 肥回归关系显著的回归模型,分析了 Zn、K_2O、B 对上述五个指标的效应,明确了 Zn 是影响各项指标的主要因子,并采用频率筛选法,提出了兼顾上述五项指标的优质高产施肥措施。     

高扬的旗帜——博山电机厂集团股份有限公司精神文明建设纪实

建厂已近60年的博山电机厂,在企业发展的历史上曾经有过辉煌:40年代,作为军工厂,在抗日战争的烽火和解放战争的硝烟中为新中国的解放事业做出了很大的贡献;50年代,作为全国八大电机厂之一,又为新中国的建设事业提供了许多优良的产品,而且作为汽车电机、直流微电机、交流     

LF6铝合金的超塑性／扩散连接组合工艺试验及理论研究EI

本文研究了ＬＦ６铝合金的超塑性／扩散连接组合工艺，用变形和再结晶的方法细化晶粒，成功地进行了ＳＰＦ／ＤＢ工艺试验，利用电子探针观察了扩散连接接头的界面微观区域，并从机理上分析了金属的超塑性／扩散连接两种工艺之间的内部联系及其金属学行为。     

渤中28－1（BZ28－1）油田N6H水平井动态分析

本文以渤中２８－１（ＢＺ２８－１）油田Ｎ６Ｈ水平井为例，从多方面对该井的动态和产能变化进行了系统分析，所用的方法对水平井动态分析有一定的指导意义。     

BONDING OF CERAMICS TO METALS WITH ACTIVATED COATING LAYERS MADE BY PLASMA SPRAYING

Bonding of ceramics to metals was carried out by using thermal sprayed coatings as interlayer materials. This bonding method is referred as the thermal spray bonding. In the present study, Si₃N₄ and Al₂O₃ ceramics were bonded to SS41 mild steel using activated Ti-Cu multilayer coatings plasma-sprayed on the steel in a low pressure atmosphere. The bondability was estimated by SEM/EDX analysis and shear tests of the joints. The results were compared to those obtained using Ti-Cu multilayer foils as interlayers. When using Ti-Cu foils as interlayers, brittle Fe-Ti compound layers were formed in the joint area after long time heating at a bonding temperature of 900°C, which deteriorated the joint strength. In contrast with the activated interlayers made by plasma spraying, the Ti-Cu eutectic reaction took place uniformly at the joint immediately after heating to the bonding temperature. This improved the bondabilrty, and the resultant joints exhibited shear strengths of about 180 MPa.