Synthesis of liquid crystalline epoxy and its mechanical and electrical characteristics—curing reaction of LCE with diamines by DSC analysis

An aromatic liquid crystalline epoxy monomer based on biphenyl mesogen was synthesized and cured with three different aromatic diamines. The curing reaction characteristics were analyzed by DSC, and the data were introduced to the Kissinger equation to attain the kinetic parameters. Diglycidyl ether of 4,4′‐biphenyl (DGEBP)/4,4′‐diaminobiphenyl (DABP), and DGEBP/4,4′‐methylenediamine (MDA) systems showed an exotherm curing reaction after comelting of the monomers; the DGEBP/p‐phenylenediamine (PDA) system's curing reaction took place in the solid state without melting of monomers. The activation energy and preexponential factor for the DGEBP/DABP system were 55.6 kJ/mol and 4.0 × 10⁶ min^?1, respectively. Those values for DGEBP/MDA and DGEBP/PDA systems were 55.1 kJ/mol and 1.0 × 10⁶ min^?1 and 148.8 kJ/mol and 7.7 × 10¹⁹ min^?1, respectively. The rate constant at 100°C for DGEBP/PDA is 2 times higher than those for DGEBP/DABP and DGEBP/MDA, which have almost the same values. Strictly speaking, the rate constant of DGEBP/DABP is a little higher than that of DGEBP/MDA, and these results are in good agreement with the DSC curves. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2419–2425, 2002     

Memory effect of locally ordered α-phase in the melting and phase transformation behavior of β-isotactic polypropylene

Structural changes in β-isotactic polypropylene (β-iPP) during the heating were studied by means of differential scanning calorimetry and real-time in situ X-ray diffraction using a synchrotron source. Crystalline phase transformation and the memory effect caused by residual nuclei of α-iPP were observed during the heating of β-iPP. The memory effect observed in β-iPP during heating and crystallization is believed to be due to the existence of locally ordered α-from in the melt. The effect of local α-form order was probed by studying the behavior under heating of samples with a range of thermal histories. Samples were heated above the equilibrium melting temperature of iPP to remove all residual local order and the memory effect associated with this local order. The samples crystallized isothermally at different temperatures exhibited a significantly different melting and phase transformation behavior during heating. β-iPP is found to be an excellent material for the study of polymorphism, phase transformations, and characteristic memory effects in semicrystalline polymers.     

Methyl tert-butyl ether decomposition over heteropoly acid catalyst in a cellulose acetate membrane reactor

In this study the methyl tert-butyl ether (MTBE) decomposition over H₃PW₁₂O₄₀ was carried out in a cellulose acetate membrane reactor. The permeability of methanol through the cellulose acetate membrane was about 30 and 300 times higher than that of either isobutene or MTBE, respectively. The isobutene selectivity in the fixed bed reactor was only slightly higher than the methanol selectivity due to the side reaction. In the cellulose acetate membrane reactor, however, the isobutene selectivity in the rejected stream was 68% and the methanol selectivity in the permeated stream was up to 97%. The MTBE conversion in the membrane reactor was about 7% higher than that in the membrane-free fixed bed reactor under the same reaction conditions. The enhanced performance of the membrane reactor in this reversible reaction was mainly due to the selective permeation of methanol which resulted in a methanol-deficient condition suppressing MTBE synthesis reaction.     

Morphology-rheology relationship in hyaluronate/poly(vinyl alcohol)/borax polymer blends

In this work, we have prepared bioartificial polymer blends using hyaluronate (HA) as a biological component and poly(vinyl alcohol)-borax association (PVAs) as a synthetic component, and investigated the rheological properties as well as morphology of the blends. When plotted against the blend composition, the rheological properties showed both positive and negative deviation from the linear additive mixing rule depending on thermal history. The blend showed enhanced viscosity at the composition of 20 wt% of HA and 80 wt% of PVAs, when PVA was dissolved at high temperature. The viscosity enhancement was caused by the network formation of HA aggregates in the micrometer scale. In addition, the network structure of HA aggregates was found to be fractal with the fractal dimension of 1.7. As PVA system also forms a network structure in the nanometer scale between hydroxyl groups of PVA and borate anions, the blend system is unique in that it has network structures in both micrometer and nanometer scales in one material. On the contrary, HA formed aggregates but not any network structure in the blend of the same composition but of the negative deviation. In conclusion, we showed that HA/PVAs blend system may have diverse morphology as well as very broad spectrum of rheological properties, and could suggest that the rheology and morphology of HA/PVAs blends can be designed not only by controlling composition but also by controlling thermal and deformation history of the components.     

Miscibility of poly(methoxymethyl methacrylate) and poly(methylthiomethyl methacrylate) with poly(vinylidene fluoride)

Summary The miscibility behaviour of poly(methoxymethyl methacrylate) (PMOMA) and poly(methylthiomethyl methacrylate) (PMTMA) with poly(vinylidene fluoride) (PVDF) was examined by differential scanning calorimetry. PMOMA/PVDF blend system was judged to be miscible on the bases of the presence of a single, composition-dependent glass transition for the blend and a pronounced melting point depression of the PVDF component. Furthermore, lower critical solution temperature (LCST) behaviour was observed for all PMOMA/PVDF blends. PMTMA/PVDF blends were found to be immiscible. Based on the melting point depression of PVDF in PMOMA/PVDF blends, the interaction parameter B was found to be -14.5 J/cm³.     

Sulfonated polyimide and poly (ethylene glycol) diacrylate based semi‐interpenetrating polymer network membranes for fuel cells

Semi‐interpenetrating polymer network (semi‐IPN) membranes based on novel sulfonated polyimide (SPI) and poly (ethylene glycol) diacrylate (PEGDA) have been prepared for the fuel cell applications. SPI was synthesized from 1,4,5,8‐naphthalenetetracarboxylic dianhydride, 4,4′‐diaminobiphenyl 2,2′‐disulfonic acid, and 2‐bis [4‐(4‐aminophenoxy) phenyl] hexafluoropropane. PEGDA was polymerized in the presence of SPI to synthesize semi‐IPN membranes of different ionic contents. These membranes were characterized by determining, ion exchange capacity, water uptake, water stability, proton conductivity, and thermal stability. The proton conductivity of the membranes increased with increasing PEGDA content in the order of 10^?1 S cm^?1 at 90°C. These interpenetrating network membranes showed higher water stability than the pure acid polyimide membrane. This study shows that semi‐IPN SPI membranes based on PEGDA which gives hydrophilic group and structural stability can be available candidates comparable to Nafion® 117 over 70°C. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effect of calcination temperature on the characteristics of SO<Emphasis Type="Italic">sk</Emphasis>4/2-/TiO<Subscript>2</Subscript> catalysts for the reduction of NO by NH<Subscript>3</Subscript>

The catalytic activity of sulfated titania (ST) calcined at a variety of temperatures has been investigated for selective catalytic reduction (SCR) of NO by NH₃. The NO removal activity of ST catalyst mainly depends on its sulfur content, indicating critical role of sulfur species on the surface of TiO₂. The role of sulfur is mainly the formation of acid sites on the catalyst surface. The presence of both BrØnsted and Lewis acid sites on the surface of sulfated titania has been identified by IR study with the adsorption of NH₃ and pyridine on ST. The reduction of the intensity of IR bands representing BrØsted acid sites is more pronounced than that revealing Lewis acid sites as the calcination temperature increases. It has been further clarified by IR study of ST500 catalyst evacuated at a variety of temperatures. The NO removal activity also decreases with the increase of the catalyst calcination temperature. It simply reveals that BrØnsted acid sites induced by sulfate on the catalyst surface are primarily responsible for the enhancement of catalytic activity of ST catalyst containing sulfur for NO reduction by NH₃.     

Effect of bentonite on the physical properties and drug‐release behavior of poly(AA‐co‐PEGMEA)/bentonite nanocomposite hydrogels for mucoadhesive

A series of nanocomposite hydrogels for mucoadhesive were prepared from acrylic acid, poly(ethylene glycol) methyl ether acrylate, and intercalated bentonite clay by photopolymerization. The microstructures were identified by X‐ray diffraction (XRD). Results showed that the swelling ratio for the present nanocomposite hydrogels decreased with an increase of bentonite, whereas the gel strength and Young's modulus of the present gels increased with an increase of bentonite. However, the adhesive force of the present gels did not decrease with an increase of bentonite. XRD results indicated that the exfoliation of bentonite was achieved in the xerogels and swollen gels. Finally, the drug‐release behaviors for these gels were also assessed. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2934–2941, 2004     

A multi-fluid nonrandom lattice fluid model: General derivation and application to pure fluids

A multi-fluid nonrandom lattice fluid model with no temperature dependence of close packed volumes of a mer, segment numbers and energy parameters of pure systems is presented. The multi-fluid nonrandom lattice fluid (MF-NLF) model with the local composition concept was capable of describing properties for complex systems. However, the MF-NLF model has strong temperature dependence of energy parameters and segment numbers of pure systems; thus empirical correlations as functions of temperature were represented for reliable and convenient use in engineering practices. The MF-NLF model without temperature dependence of pure parameters could not predict thermodynamic properties accurately. It was found that the present model with three parameters describes quantitatively the vapor pressure and the saturated density for the pure fluid.     

Synthesis and characterization of in situ polymerized segmented thermoplastic elastomeric polyurethane/layered silicate clay nanocomposites

Nanocomposites based on thermoplastic elastomeric polyurethane (TPU) and layered silicate clay were prepared by in situ synthesis. The properties of nanocomposites of TPU with unmodified clay were compared with that of organically modified clay. The nanocomposites of the TPU and organomodified clay showed better dispersion and exhibited superior properties. Exfoliation of the clay layers was observed at low organoclay contents, whereas an intercalated morphology was observed at higher clay contents. As one of major purposes of this study, the effect of the silicate layers in the nanocomposites on the order–disorder transition temperature (T_ODT) of the TPU was evaluated from the intensity change of the hydrogen‐bonded and free carbonyl stretching peaks and from the peak position change of the N? H bending peak. The presence of the organoclay increased T_ODT by approximately 10°C, which indicated improved stability in the phase‐separated domain structure. The layered silicate clay caused a tremendous improvement in the stiffness of the TPU; meanwhile, a reduction in the ultimate elongation was observed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3048–3055, 2006