Dynamic probe of ZnTe(110) surface by scanning tunneling microscopy

The reconstructed surface structure of the II–VI semiconductor ZnTe (110), which is a promising material in the research field of semiconductor spintronics, was studied by scanning tunneling microscopy/spectroscopy (STM/STS). First, the surface states formed by reconstruction by the charge transfer of dangling bond electrons from cationic Zn to anionic Te atoms, which are similar to those of IV and III–V semiconductors, were confirmed in real space. Secondly, oscillation in tunneling current between binary states, which is considered to reflect a conformational change in the topmost Zn–Te structure between the reconstructed and bulk-like ideal structures, was directly observed by STM. Third, using the technique of charge injection, a surface atomic structure was successfully fabricated, suggesting the possibility of atomic-scale manipulation of this widely applicable surface of ZnTe.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

以辉锑矿为原料放电等离子烧结快速制备黝铜矿Cu_(12)Sb_4S_(13)及反应机理

采用辉锑矿为原料成功制备出Cu_(12)Sb_4S_(13)块体。研究以Sb_2S_3矿物为原料时烧结工艺对Cu_(12)Sb_4S_(13)合成的影响。在400 ～ 440℃温度区间内均可快速合成Cu_(12)Sb_4S_(13)块体且二次烧结能够进一步减小中间相CuSbS_2和Cu_3SbS_3。第二相Cu_3SbS_4和残留相CuS随着烧结时间的延长而降低。二次烧结前进行机械化球磨处理,干磨比湿磨更容易减小残留相。初次烧结块体的断面SEM和EDS能谱分析表明内部存在Cu或Cu_2S颗粒团聚现象。适当降低Cu或CuS摩尔量(化学计量比0.1 mol)能促进烧结块表面反应进行。烧结过程中,硫磺蒸汽压的导致烧结块表面成分和内部粉末的成分不同。     

Transient analysis of an advanced static var compensator using quad-series voltage-source PAM inverters

This paper deals with an advanced static Var compensator (ASVC) using quad-series voltage-source PAM inverters. The ASVC consists of four three-phase voltage-source inverters with a common dc capacitor and four three-phase transformers, each primary winding of which is connected in series with each other. Each inverter outputs a square-wave voltage, while the synthesized output voltage of the ASVC has a 24-step wave shape. This results not only in a great reduction of harmonic currents and dc voltage ripples but also in fewer switching and snubbing losses. In this paper, transient analysis is performed with the focus on the response of reactive power and the resonance between the dc capacitor and ac reactors. Experimental results obtained from a small-rated laboratory model of 10 kVA are also shown to verify analytical results based on the p-q transformation. The analytical results help in the design of system parameters such as the capacity of the dc capacitor and feedback gains.     

Crystal orientation of β-phase isotactic polypropylene induced by magnetic orientation of N,N′-dicyclohexyl-2,6-naphthalenedicarboxamide

Melt crystallization of isotactic polypropylene (iPP), containing crystallites of N,N′-dicyclohexyl-2,6-naphthalenedicarboxamide (DCNDCA) as a nucleating agent of the the β-phase iPP crystal, is carried out under a magnetic field (6 T) to obtain the alignment of the iPP crystal induced by magnetic alignment of DCNDCA. In a previous paper, DCNDCA was reported to undergo magnetic alignment in a liquid suspension. The obtained iPP sample exhibits alignment of the β-phase crystal with the c-axis aligned perpendicular to the magnetic field. The comparison of this alignment of iPP with the reported magnetic alignment of DCNDCA indicates that the β-phase crystal grows epitaxially on the DCNDCA crystal. The (330)_β plane of the iPP crystal lies on the bc-plane of the DCNDCA crystal in which the direction of the c-axis of the iPP coincides with the direction of the b-axis of the DCNDCA crystal.     

Sensorless control of synchronous reluctance motors using on‐line parameter identification method not affected by position estimation accuracy

This paper presents a novel on‐line parameter identification method for sensorless control of Synchronous Reluctance Motors (SynRMs). Although conventional sensorless control methods based on mathematical models usually need some complex measurements of motor parameters in advance, the proposed identification method does not require them and can be realized on‐line. The proposed method identifies motor parameters under sensorless control, so rotor position and velocity cannot be used to identify these parameters. However, the proposed method does not need rotor position and velocity, and identified parameters are not affected by these estimation errors. The sensorless control using identified motor parameters is realized, and the effectiveness of the proposed method is verified by experimental results. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(3): 62–69, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20258     

Combining natural language with direct manipulation: the conceptual framework for a hybrid human-computer interface

This paper describes the development of a conceptual model of an interaction system for future human-computer interaction. It is suggested that an integrated system is the most promising solution for diverse users and tasks. A ' hybrid interaction system' is considered, which tries to efficiently direct manipulation, menu selection, and natural language. The mechanism of the natural language interface module is described in more detail. Finally, the allocation of functionalities for generalized tasks on the conceptual model is considered from the taxonomic approach.     

Sintering of Confined Silica in Oxidized Silicon Particles

We observed electron-beam-induced sintering of amorphous silica in oxidized submicrometer silicon particles and analyzed the nature of mass transport in linear and triangular particle assemblies. The movement of silica around the rigid crystalline cores occurs rapidly and fills the necks, but the relative core positions in the sintered product depends on the initial geometry of the confined oxide. However, a thin layer of silica remains stable against the flow.