压铸高强韧Al-Cu系合金的组织性能及热处理

为了弥补目前压铸铝合金强韧性不足,进行了高强韧铝铜系合金的压铸及热处理的试探性研究.在ZL201的基础上,添加合金化元素B、Zr、V等,改善合金的铸造性能,进行压铸试验.试验研究发现压铸大大细化了合金的微观组织,铸态性能较金属型高,再经低温时效后合金强度达到一般高强压铸铝合金的水平,但塑性较之提高20%以上.     

离心铸造不锈钢空心管坯裂纹缺陷的探讨

介绍了离心铸造1Cr18Ni9Ti钢管坯产生的裂纹形态;从理论上探讨了裂纹产生机理并提出了预防和消除裂纹的措施及较佳的铸造工艺参数。     

Induced effects of Cu underlayer on（111） orientation of Fe50 Mn50 thin films

Effects of Cu underlayer on the structure of Fe50 Mn50 films were studied. Samples with a structure of Fe50 Mn50 (200 nm)/Cu(tcu) were prepared by rnagnetron sputtering on thermally oxidized silicon substrates at room temperature. The thickness of Cu underlayer varied from 0 to 60 nm in the intervals of 10 nm. High-vacuum annealing treatments, at different temperatures of 200, 300 and 400℃ for 1 h, respectively, on the Fe50Mn50 (200 nm)/Cu(20 nm) thin films were performed. The surface morphologies and textures of the samples were measured by field emission scan electronic microscope (FE-SEM) and X-ray diffraction(XRD). Energy dispersive X-ray spectroscopy (EDX) and Auger electron spectroscopy(AES) were used to analyze the compositional distribution. It is found that Cu underlayer has an obvious induce effect on (111) orientation of Fe50 Mn50 thin films. The induce effects of Cu on (111) orientation of Fe50 Mn50 changed with the increase of Cu layer thickness and the best effect was obtained at the Cu layer thickness of 20 nm. High-vacuum annealing treatments cause the migration of Mn atoms towards surface of the film and interface between Cu layer and substrate. With the increasing annealing temperature, migration of Mn atoms is more obvious, which leads to a Fe-riched Fe-Mn alloy film.     

Mechanical properties and microstructures of hot extruded AE42 alloy with addition of zinc

Mechanical properties and microstructures of AE42 magnesium alloy with addition of Zn and subjected to hot extrusion at 370 ℃ and an extrusion ratio of 8：1 were investigated. The results show that for the AE42 alloy, the addition of Zn can obviously improve its elongation as well as the ultimate tensile and yield strengths below 150 ℃. The addition of Zn can refine the mierostructure of the AE42 alloy, and result in the precipitation of Mg17Al12 and MgZn2 phases. Due to the addition of Zn to the AE42 alloy, the amount of Al11RE3 phase decreases, while the Al11RE3 phase becomes short rod-shaped from acicular and block, and distributes along the grain boundaries, which will have a stronger effect on the tensile properties of the alloy at elevated temperature. In addition, with the presence of MgZn2 precipitates, the sliding of grain boundaries is restrained and the strength of the alloy gets enhanced.     

冒口重量网络图确定法

以圆柱和腰圆冒口为例，提出了坐标曲线网络图方法，根据已知的冒口尺寸即可由坐标曲线网络查取任一冒口重量。     

AZ91D-RE-xCa镁合金挤压管件组织及性能

研究了镁合金AZ91D加入混合RE及Ca进行合金化后的AZ91D-RE-xCa（x=0．5、1．0、1．5）镁合金挤压管件的显微组织、室温及高温（150℃和200℃）力学性能。结果表明，合金化之后的镁合金挤压管件高温性能得到了显著的提高。在200℃时，钙含量（质量分数）为0．5％时，δb为225．2MPa，δ0.2为179．3MPa，δ为5．3％，好于同等试验条件下的镁合金AZ91D管件。     

计算机网络技术对人工智能的应用

近年来,人工智能日益成为科学技术的前沿领域,世界各国也高度重视人工智能的发展。人工智能的发展离不开计算机网络技术。本文介绍了人工智能,分析了人工智能技术的优势以及在计算机网络技术中的应用。     

网购“星际2”必知的4件事

《星际争霸》在12年前推出时,凭借着超前的游戏理念和均衡的种族设计,引领了局域网对战游戏的潮流。如今,随着《星际争霸2》这款超一流游戏的推出,     

燃气表无线抄表系统的设计与实现

针对现在抄表系统复杂度高或成本高等问题,本文设计了一套燃气表无线抄表系统,从基本架构、主要功能、软硬件的实现加以说明,具有实时、可靠、经济、低功耗等优点.该系统采用M430F413和EM78P153S为控制单元,CC1100为无线通信单元.该系统稳定可靠,具有良好的应用和推广价值.     

C8051F单片机在自动机器人上的应用

以2007年CCTV大学生机器人大赛自动机器人为对象,系统阐述了自动机器人的控制电路.