基于μVision2的单片机C程序调试

在没有硬件仿真系统或在线调试器时,如何对系统进行调试或仿真,介绍基于μVision2环境下的程序调试与软件仿真方法,合理使用这些方法模拟实际运行环境,验证程序设计,可以减少调试时间,提高编程效率.     

Influence of Structure Parameters of Double-angle Liner on Jet Formation

By using LS-DYNA simulation software,the influences of some structure parameters,such as top cone angle,wall thickness,liner height and height ratio of top cone,of double-angle liner on the jet formation were studied respectively.Their influences on jet tip velocity,tail velocity and penetration depth were revealed.The simulation results show that the formation is better if the top cone angle is selected as 28°,the wall is 2.6mm,the liner height is 140mm,and the height ratio of top cone is 60%.In large stand-off distance,the jet has a higher tip velocity,and the tip does not break.With the stand-off distance of 8 times of the charge diameter,the experiment penetrating steel target was carried out.The experiment and simulation results are in good agreement.     

TCSC过电压保护方式研究

TCSC的过电压保护主要研究故障情况下保护TCSC和MOV的方式以及如何降低MOV能耗水平,以满足经济性要求,同时又有利于系统暂态稳定。在分析TCSC过电压保护方式与暂态稳定关系的基础上,提出过电压保护的控制策略,研究了保护性旁路的启动方式,并借助ARENE软件予以仿真验证。     

Valence electron structures and properties of Ni-based corrosion resistant alloy

The corrosion resistance and mechanical properties were tested and compared for the newly synthesized as-cast, as-solution Ni-Cr-Mo-Cu corrosion resistant alloys and 1Cr18Ni9Ti austenitic stainless steel. Their valence electron structural units were constructed, and the relative parameters were calculated by means of the Empirical Electron theory of Solids and Molecules （EET）. The results show that, during alloy elements Cr, Mo and Cu entering Ni-matrix, the bonding strength nA and bonding energy EA of the strongest bond of the alloy are greatly increased, causing the stronger solid solution strengthening effects （about 30% increase in σb）. Also, as reinforcement of the main bond network and the improvement of stability of the alloy system due to the solution of these alloying elements in γ-Ni, the ionization of metal atoms in corrosion solution and the flow of electrons from anode to cathode would all be impeded during electro-chemical corrosion processes, which leads to the excellent corrosion resistant ability of the present Ni-Cr-Mo-Cu alloy （about 2-3 orders of magnitude as high as 1Cr18Ni9Ti austenitic stainless steel） in several highly aggressive solutions.     

机器噪声平均声压级计算方法差异性实证研究

针对家用电器、电动工具、电弧焊机、容积式压缩机、水泵、风机等机器的噪声平均声压级计算过程,介绍典型的机器噪声平均声压级计算方法。分析多种计算方法的差异,同时给出确定噪声平均声压级推荐采用的计算方法。     

灰色理论在塑料老化行为预测中的应用研究

根据灰色理论构建GM(1,1)预测模型,以湿热条件下聚丙烯和蒙脱土/聚丙烯纳米复合材料的拉伸强度变化的预测为例,研究所建预测模型在塑料老化行为预测中的适用性。聚丙烯和蒙脱土/聚丙烯纳米复合材料拉伸强度的预测结果表明,所建模型的预测精度等级为1级,模拟值与实际值的相对误差最大为4.25%,可用于塑料老化行为的预测。灰色GM(1,1)模型所需实验数据少,预测精度高,为塑料老化行为的预测提供了一种简易而可靠的新途径。     

连续管式结晶器研究进展

结晶是大多数化工生产过程中必不可缺的步骤。目前,大部分结晶过程采用间歇结晶,但间歇结晶的生产模式存在批次间差异、生产成本过高等缺点。因此,连续结晶作为新的结晶模式逐渐成为研究的重点。其中,连续管式结晶器具有较窄的停留时间分布和较高的生产效率等优势,已广泛应用于工业结晶。针对连续管式结晶器研究现状进行了详细介绍,总结了管式结晶器普遍存在的问题和解决方法,并介绍了辅助设备和技术在连续管式结晶器中的应用。最后,总结了管式结晶器的进一步发展方向。     

六辊CVC轧机的结构原理及优点

介绍CVC轧机的结构、原理及应用情况。     

热带钢平整工艺及设备配置

介绍热带钢平整的作用、工艺及设备组成。并与冷带钢平整设备做比较。