Effect of surface properties of silica nanoparticles on their cytotoxicity and cellular distribution in murine macrophages

In this study, complexes composed of poly-l-tyrosine (pLT) and single-walled carbon nanotubes (SWCNTs) were produced and the dispersibility of the pLT/SWCNT complexes in water by measuring the ζ potential of the complexes and the turbidity of the solution were investigated. It is found that the absolute value of the ζ potential of the pLT/SWCNT complexes is as high as that of SWCNTs modified with double-stranded DNA (dsDNA) and that the complexes remain stably dispersed in the water at least for two weeks. Thermogravimetry analysis (TGA) and visualization of the surface structures of pLT/SWCNT complexes using an atomic force microscope (AFM) were also carried out.     

In situ time-resolved X-ray diffraction of tobermorite formation in autoclaved aerated concrete: Influence of silica source reactivity and Al addition

The hydrothermal formation of tobermorite during the processing of autoclaved aerated concrete was investigated by in situ X-ray diffraction (XRD) analysis. High-energy X-rays from a synchrotron radiation source in combination with a newly developed autoclave cell and a photon-counting pixel array detector were used.To investigate the effects of the silica source, reactive quartz from chert and less-reactive quartz from quartz sand were used as starting materials. The effect of Al addition on tobermorite formation was also studied. In all cases, C-S-H, hydroxylellestadite and katoite were clearly observed as intermediates.Acceleration of tobermorite formation by Al addition was clearly observed. However, Al addition did not affect the dissolution rate of quartz. Two pathways, via C-S-H and katoite, were also observed in the Al-containing system. These results suggest that the structure of initially formed C-S-H is important for the subsequent tobermorite formation reactions.     

Application of CO2 laser heating zone drawing and zone annealing to nylon 6 fibers

Nlon 6 fibers were zone drawn and zone annealed by using a continuous wave carbon dioxide laser to develop their mechanical properties. A laser‐heating zone drawing was carried out under a applied tension of 35.4 MPa at a power density of 9.65 W · cm^?2, and then the zone‐drawn fiber was annealed. A laser‐heating zone annealing was carried out in two steps at a power density of 9.65 W · cm^?2; the first step was carried out under 423 MPa and the second under 517 MPa. The treating temperature of the fiber heated by the CO₂ laser was measured by using an infrared thermographic camera equipped with a magnifying lens. The treating temperature at the zone drawing is 138°C, and those at the first and the second zone annealing are 121 and 125°C, respectively. The second laser‐heated zone‐annealed fiber has a birefringence of 65.2 × 10^?3, a degree of crystallinity of 54%, and a storage modulus of 21 GPa at 25°C. Wide‐angle X‐ray diffraction patterns for the laser‐heated zone‐drawn and the zone‐annealed fibers show (200) reflection and (002/202) doublet due to only an α form on the equator. The laser‐heated zone‐drawn fiber has a melting endotherm peaking at 216°C and a trace of shoulder on the higher temperature side of its peak, and the laser‐heated zone‐annealed fibers have a single melting endotherm peaking at 216°C. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1711–1716, 2002     

Ethanol production from raw starch by a recombinant yeast having saccharification and fermentation activities

In order to develop a method for converting raw starch into ethanol efficiently, direct fermentation of ozonized raw starch using a recombinant yeast was investigated. Ozonolysis was carried out as a pretreatment to convert raw starch into ethanol rapidly and efficiently, and then the effect of the ozone degradation conditions on the degree of polymerization and the amount of amylose in a raw starch was determined. Since the degree of polymerization was low and the amount of amylose was high, raw starch treated with an ozone concentration of 40 gm^?3 and an ozonation time of 30 min was the material chosen for alcohol fermentation. Though the recombinant yeast could not convert the untreated raw starch, it converted the soluble starch and the ozonized raw starch at a comparatively high yield into ethanol. About 56% of the ozonized raw starch decomposed, and the ethanol concentration obtained from the ozonized raw starch was markedly greater than that obtained from untreated raw starch. The dynamic behavior of cell growth, substrate degradation, and ethanol production was examined in a continuous culture under various dilution rates, and the optimal dilution rate, ie 0.15 h^?1, was determined for maximizing the ethanol productivity (amount of ethanol produced per unit time). © 2002 Society of Chemical Industry     

Properties of graphite prepared from boron-doped pitch as an anode for a rechargeable Li ion battery

Boron-doped graphites were derived from a naphthalene-based pitch mixed with para-xylene glycol (PXG) or dimethyl para-xylene glycol (DMPXG) as a cross-linking agent and three types of boron-containing compounds as a graphitization catalyst, and their anode performances were investigated. The structural analysis of the obtained graphites revealed that PXG functioned mainly as a two-dimensional cross-linking agent during the heat treatment process and DMPXG functioned partially as a three-dimensional. The average interlayer spacing decreased and lattice constant, a₀, and graphitizability increased with increasing the amount of boron atoms added. The result indicated that the carbon atoms were replaced by boron atoms. The anode performance was improved by the enhancement of graphitizability. The structural parameters and anode performance of boron-doped graphites did not depend on the kind of boron-containing compounds but the amount of boron atoms added in pitch and the kind of cross-linking agent.     

Heavy oil sorption and recovery by using carbon fiber felts

On fibrous carbon materials, including activated carbon fibers, sorption capacity for heavy oils, less viscous A-grade and more viscous C-grade, was determined. Sorption capacity depended strongly on their bulk density; the correlation was the same as that found previously on exfoliated graphite and carbonized fir fibers. On carbon fiber felts, excellent recycling performance was observed, though sorption capacity was not so high as on exfoliated graphite and carbonized fir fibers. By filtration under suction, about 90% of sorbed A-grade heavy oil could be recovered and no decrease in sorption capacity was detected even after eight cycles. By washing with solvents, n-hexane for A- and C-grade oils and A-grade oil for C-grade oil, almost 100% recovery with no marked reduction in sorption capacity was found for each cycle. For the felts of PAN-based carbon fibers, rather severe operations for oil recovery, centrifugation and squeezing with twisting, could be applied without pronounced decreases in sorption capacity and recovery ratio.     

Effect of agglomeration of triacylglycerols on the stabilization of a model cream

This study has been carried out on solidification of a model cream using palm oil as a sole fat source. It was found that the addition of 1‐palmitoylglycerol to palm oil promoted the solidification of the model cream while the addition of 1‐oleoylglycerol had no such effect. Solid fat content of palm oil in the cream with 1‐palmitoylglycerol was found to be lower than those of palm oil and palm oil with 1‐oleoylglycerol after cooling from 60 to 5 °C. Crystallization behaviors of bulk palm oil and mixture of 1, 3‐dipalmitoyl‐ 2‐oleoyl‐glycerol (POP) and 1‐palmitoyl‐2, 3‐dioleoyl‐glycerol (POO) were then studied in the presence of monoacylglycerols. Formation of granular crystals was observed for palm oil and POP/POO mixture in the presence of 1‐palmitoylglycerol. HPLC of the granular crystals revealed that agglomeration of higher melting point triacylglycerols (TAGs) around 1‐palmitolyglycerol took place, which promoted the formation of granular crystals. It was suggested that the agglomeration of higher melting point TAGs around 1‐palmitoylglycerol which was preferentially adsorbed at the oil‐water interface of oil droplets in the model cream led to destabilization of oil‐in‐water emulsion and the solidification of the model cream. At the same time, it was suggested that the fatty acid moiety of emulsifiers played an important role in the agglomeration of TAGs and stabilization of o/w emulsions.     

Fractionation and enrichment of CLA isomers by selective esterification with Candida rugosa lipase

A commercial product of CLA contains almost equal amounts of cis-9,trans-11 (c9,t11)-CLA and trans-10,cis-12 (t10,c12)-CLA. We attempted to enrich the two isomers by a two-step selective esterification using Candida rugosa lipase that acted on c9,t11-CLA more strongly than on t10,c12-CLA. An FFA mixture containing CLA isomers was esterified with an equimolar amount of lauryl alcohol in a mixture of 20% water and the lipase. When the esterification of total FA reached 50%, two isomers were fractionated in a good yield: t10,c12-CLA was enriched in FFA, and c9,t11-CLA was recovered in lauryl esters. The FFA were esterified again to enrich t10,c12-CLA. At 27.3% esterification of total FA, the t10,c12-CLA content in FFA increased to 64.8 wt% with 89.3% recovery: The ratio of the content of t10,c12-CLA to that of two isomers was 95.9%. Lauryl esters obtained by the single esterification were employed for enrichment of c9,t11-CLA. After the esters were hydrolyzed, the resulting FFA were esterified again with lauryl alcohol. At 62.0% esterification of total FA, the c9,t11-CLA content in lauryl esters increased to 73.3 wt% with 79.4% recovery: The ratio of the content of c9,t11-CLA to that of two isomers was 95.6%. In a 600-g-scale purification, molecular distillation was effective in separating the reaction mixture into lauryl alcohol, FFA, and lauryl ester fractions.     

γ‐Butyrolactone‐processable high‐modulus poly(ester imide)s

γ‐Butyrolactone (GBL)‐processable high modulus heat‐resistant materials were developed in this work. The polyaddition of an ester‐containing tetracarboxylic dianhydride, i.e. hydroquinone bis(trimellitate anhydride) (TAHQ), and 2,2′‐bis(trifluoromethyl)benzidine (TFMB) in GBL resulted in gelation in the initial reaction stage. The incorporation of a methyl group to TAHQ (M‐TAHQ) allowed polymerization with TFMB in GBL and led to a homogeneous poly(ester imide) (PEsI) precursor solution with a short pot life of 3 days, whereas a simple copolymerization approach using bulky/flexible comonomers to TAHQ/TFMB was less effective. PEsI precursors (PEsAAs) were prepared from TFMB, M‐TAHQ and a minor fraction of 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride (6FDA) or a fluorene‐containing tetracarboxylic dianhydride. These PEsAA systems showed drastically improved GBL solution stability. In particular, the M‐TAHQ(80);6FDA(20)/TFMB copolymer system provided a PEsAA film with a very high light transmittance at 365 nm (>70%). A photosensitive film composed of this matrix resin and diazonaphthoquinone provided a clear positive‐tone pattern by development in a 2.38 wt% tetramethylammonium hydroxide aqueous solution at room temperature with a high dissolution contrast. The thermally cured PEsI film achieved a very high tensile modulus (>5 GPa) as the present target with other desirable properties, i.e. sufficient film flexibility, a relatively low coefficient of thermal expansion, a high T_g and low water absorption. The present materials can be promising candidates as novel buffer coat films in semiconductor applications. Copyright © 2011 Society of Chemical Industry