Design of electrofusion joints and evaluation of fusion strength using fusion simulation technology

Fusion simulation is one of the key techniques in designing and producing electrofusion (EF) joints for gas distribution and in evaluating fusion joint integrity. This paper describes the result of a numerical simulation of a thermal fusion process, using the finite element method. A nonlinear heat transfer computer program was used to obtain the temperature profile of a large electrofusion joint at fusion. The effects of applied voltage, heating time, wire pitch, and ambient temperature were examined for designing a 150-mm EF joint. A method to shorten the cooling time was also investigated. The fusion condition range suitable for a 150-mm EF joint was found to be slightly narrower than that suitable for a 50-mm EF joint. Examination of the effect of wire pitch revealed that if the pitch is extremely large, thermal degradation starts in the resin close to the wire before the fusion-interface strength reaches the maximum value. We have developed a program to simulate the process of closing the gap between the pipe and the joint due to resin expansion and melting after the power is supplied.     

Intelligent manipulator system with nonsymmetric and redundant master-slave

Some work is so complicated and unsteady that it is not possible to use automatic robots, such as FA robots. In such a case, a teleoperated manipulation system is applied. In this research, the authors aim at a reduction in the operator's physical and mental burdens. An artificially intelligent manipulator system has been developed with nonsymmetric and redundant master-slave. This system has five features: (1) a polar coordinates master arm; (2) a highly operational articulated slave arm with 7 degrees of freedom; (3) a nonsymmetric configuration and different degrees of freedom master-slave control; (4) an expert system; and (5) a new master-slave control motion, which makes the operator's task easier with automatic force/position control. The system was experimentally produced and its performance tested and evaluated. A qualitative evaluation was carried out by conducting a comparative test on the conventional master-slave control and the new master-slave control. It was found to be effective in reducing operating time, as well as work-induced fatigue.     

Sinterability and properties of Ti(N1−x,O x ) y -(V,Ta)C-Ni sintered alloys having a golden colour

The effect of oxygen and carbide addition on the sinterability of TiN _y (0.42<y<1)-Ni alloys, in which part of the nitrogen is replaced by oxygen was investigated. It was found that sinterability increased as the oxygen and carbide content increased, but the strength of the resultant sintered alloys was significantly reduced due to the presence of Ni₃Ti and Ti₂O₃ phases when the oxygen content exceeded 50 mol %. The sintered alloy with the highest hardness was found whenx=0.7,y=0.78 and the (V,Ta)C content was 18% by weight and this alloy was characterized by having a low density, good corrosion resistance and the colour of gold.     

New field measurement system for single-mode fibre dispersion utilising wavelength division multiplexing technique

A new system designed to measure the chromatic dispersion of installed single-mode fibres is presented. This system utilises the modulation phase technique but eliminates the reference laser and fibre. A large dynamic range was demonstrated by the measurement of an 81.1 km length of fibre.     

New low-noise output amplifier for high-definition CCD image sensor

A new low-noise charge-coupled-device (CCD) output amplifier, the RJG detector, has been developed. The RJG detector incorporates a JFET which has an electrically floating ring-junction gate (RJG). The operating principle of the amplifier is that signal charges, transferred from the CCD into the RJG, directly modulate the drain current in the detection JFET. The performance of the detector was evaluated by operating test devices under a 37-MHz clock frequency, which is the same frequency as that for the horizontal CCD operation in the recently developed 2-million-pixel high-definition CCD image sensor. It was found that 1/f noise was reduced by introducing the JFET and that reset noise was completely eliminated by achieving complete charge transfer through the reset operation. As a result, input referred noise equivalent electrons within the 18.5-MHz baseband were reduced to 17 (electrons)     

Formation of dityrosine and other fluorescent amino acids by reaction of amino acids with lipid hydroperoxides

Formation of fluorescence by the reaction of various amino acids with lipid hydroperoxides,i.e., linoleic acid 13-monohydroperoxide, methyl linoleate 13-monohydroperoxide and phosphatidylcholine hydroperoxide, in the presence of methemoglobin was investigated. Two types of fluorescence were produced: fluorescent dityrosine (3,3′-dityrosine) from tyrosine, and unidentified fluorophores with α- and ε-amino groups of various amino acids. While the former was stable after treatment with borohydride, the latter fluorophores were readily destroyed. The rate of dityrosine formation was rapid, and the yield of dityrosine was dependent on the concentrations of tyrosine and the lipid hydroperoxides. Butylated hydroxytoluene and tocopherol inhibited the formation of dityrosine, but did not affect the formation of fluorophores on the amino groups. Dityrosine appears to be formed by radical reaction of the lipid hydroperoxides, while the other fluorophores seem to be created by nonradical mechanisms.     

Hydrothermal upgrading of wood biomass: Influence of the addition of K2CO3 and cellulose/lignin ratio

The hydrothermal treatment of two different wood biomass samples such as cherry (hard wood) and cypress (soft wood), whose composition is different i.e. lignin, cellulose and hemicellulose were performed at 280 °C for 15 min with aq. K₂CO₃ with different concentrations (0–1 M). The soft wood biomass contains higher lignin content than hard wood biomass. The cellulose rich cherry wood biomass produced higher proportion of acetic acid than cypress. The lignin rich cypress produced the hydrocarbons with major portion of phenolic hydrocarbons and derivatives than cherry. The total oil yields from both cherry and cypress wood biomass produced 50 wt% of liquid hydrocarbons at 280 °C for 15 min with 0.5 M K₂CO₃ solution. The volatility distribution of liquid hydrocarbons showed the characteristic features of soft and hard wood biomasses.     

Effect of functional group of ferrocene redox substance on the transport properties of newly designed ion exchange membrane prepared from polymer gel

A different newly designed cationic exchange polymer membrane and anionic exchange polymer membrane were introduced, and also the transport properties of these polymeric membranes were investigated in this study. The transport properties of these polymer membranes in contact with ferrocene redox derivatives were estimated by using electrochemical techniques such as cyclicvoltammetry, chronopotentiometry, and chronoamperometry techniques, respectively. The used ferrocene redox substances, which have different functional groups, were (Ferrocenylmethyl) trimethylamonium iodide, FcMA, Ferrocenedimethanol, FcDM, and Ferrocene carboxylic acid, FcCA. It indicated that the performance of a membrane depended on the content of polymer gel, anionic exchange polymer site (20 wt % and 50 wt %) or cationic polymer exchange site (20 wt % and 50 wt %), and the efficiency of the functional groups of cationic and anionic exchange polymer site as well. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of 8 MeV electron irradiation on electrical properties of CuInSe2 thin films

Radiation damages due to 8 MeV electron irradiation in electrical properties of CuInSe₂ thin films have been investigated. The n-type CuInSe₂ films in which the carrier concentration was about 3×10¹⁶ cm⁻³, were epitaxially grown on a GaAs(0 0 1) substrate by RF diode sputtering. No significant change in the electrical properties was observed under the electron fluence <3×10¹⁶ e cm⁻². As the electron fluence exceeded 10¹⁷ e cm⁻², both the carrier concentration and Hall mobility slightly decreased. The carrier removal rate was estimated to be about 0.8 cm⁻¹, which is slightly lower than that of III–V compound materials.     

Solving #SAT using vertex covers

We propose an exact algorithm for counting the models of propositional formulas in conjunctive normal form. Our algorithm is based on the detection of strong backdoor sets of bounded size; each instantiation of the variables of a strong backdoor set puts the given formula into a class of formulas for which models can be counted in polynomial time. For the backdoor set detection we utilize an efficient vertex cover algorithm applied to a certain “obstruction graph” that we associate with the given formula. This approach gives rise to a new hardness index for formulas, the clustering-width. Our algorithm runs in uniform polynomial time on formulas with bounded clustering-width. It is known that the number of models of formulas with bounded clique-width, bounded treewidth, or bounded branchwidth can be computed in polynomial time; these graph parameters are applied to formulas via certain (hyper)graphs associated with formulas. We show that clustering-width and the other parameters mentioned are incomparable: there are formulas with bounded clustering-width and arbitrarily large clique-width, treewidth, and branchwidth. Conversely, there are formulas with arbitrarily large clustering-width and bounded clique-width, treewidth, and branchwidth.