Adhesion between oppositely charged polyelectrolytes

The adhesion between a grafted polyelectrolyte layer (brush) and a gel of an oppositely charged polyelectrolyte has been measured as a function of applied pressure, and the interface has been traced using neutron reflectometry. The interface (in aqueous medium at pH 6) between the (polycationic) brush and the (polyanionic) gel has a limited pressure dependence, with a small amount of deformation of the interface at the brush–gel contact. Brushes with a dry thickness of up to 13 nm exhibit weak adhesion (measured using a mechanical force tester) with an adhesive failure when the gel is detached. Thicker brushes result in the gel exhibiting cohesive failure. Reversing the geometry, whereby a polycationic brush is replaced with a polyanion and the polyanionic gel is replaced with a polycation, reveals that the pH dependence of the adhesion is moderately symmetric about pH 6, but that the maximum force required to separate the polycation gel from the polyanion brush over the range of pH is greater than that for the polycation brush and polyanion gel. The polyanion used is poly(methacrylic acid) (PMAA) and polycations of poly[2-(diethylamino)ethyl methacrylate] (PDEAEMA) and poly[2-(dimethylamino)ethyl methacrylate] (PDMAEMA) were used.     

Threshold Levels for Bromate Formation In Drinking Water

Ozone is a sufficiently strong oxidant to cause the oxidation of bromide ion and formation of bromate ion. In this study, bromate ion formation in a wide variety of drinking water sources was analyzed, with bromate ion formed in all sources under drinking water treatment conditions. Threshold levels for pH, bromide ion concentration, and ozone dose were found to be source-specific. Two non-linear empirical models were developed to predict bromate ion formation; these models are easy to use and require only several water quality and treatment variables. The models were tested against several literature data and a good simulation was found in other bench-scale tests, whereas the model tended to under-predict bromate ion formation in pilot-scale and full-scale programs.     

Computer-controlled Raman microspectroscopy (CC-Raman): A method for the rapid characterization of individual atmospheric aerosol particles

The ability of an atmospheric aerosol particle to impact climate by acting as a cloud condensation nucleus (CCN) or an ice nucleus (IN), as well as scatter and absorb solar radiation is determined by its physicochemical properties at the single particle level, specifically size, morphology, and chemical composition. The identification of the secondary species present in individual aerosol particles is important as aging, which leads to the formation of these species, can modify the climate relevant behavior of particles. Raman microspectroscopy has a great deal of promise for identifying secondary species and their mixing with primary components, as it can provide detailed information on functional groups present, morphology, and internal structure. However, as with many other detailed spectroscopic techniques, manual analysis by Raman microspectroscopy can be slow, limiting single particle statistics and the number of samples that can be analyzed. Herein, the application of computer-controlled Raman (CC-Raman) for detailed physicochemical analysis that increases throughput and minimizes user bias is described. CC-Raman applies automated mapping to increase analysis speed allowing for up to 100 particles to be analyzed in an hour. CC-Raman is applied to both laboratory and ambient samples to demonstrate its utility for the analysis of both primary and, most importantly, secondary components (sulfate, nitrate, ammonium, and organic material). Reproducibility and precision are compared to computer controlled-scanning electron microscopy (CCSEM). The greater sample throughput shows the potential for CC-Raman to improve particle statistics and advance our understanding of aerosol particle composition and mixing state, and, thus, climate-relevant properties.

© 2017 American Association for Aerosol Research     

Evaluation of Simple and Inexpensive High-Throughput Methods for Phytic Acid Determination

High‐throughput/low‐cost/low‐tech methods for phytic acid determination that are sufficiently accurate and reproducible would be of value in plant genetics, crop breeding and in the food and feed industries. Variants of two candidate methods, those described by Vaintraub and Lapteva (Anal Biochem 175:227–24, 1988 ; “VL” methods) and Huang and Lantzsch (J Sci Food Agric 34:1423–1426, 1983 ; “HL” methods), were evaluated. The primary concern with these methods is that, due to interference of matrix constituents including inorganic P, they can overestimate phytic acid and are ineffective at low levels of phytic acid. Twelve seed flours, representing lines of soybean, maize, barley and dry bean, containing a wide range of phytic acid levels, were analyzed by a minimum of eight cooperating laboratories using three variants of the VL method and two variants of the HL method. No method had consistently acceptable (?2.0”) “Horwitz ratios”, a measure of reproducibility, although some treatments approached that. For example, one variant of the VL method when used to assay a soybean flour with a “standard” level of phytic acid had a Horwitz ratio of 2.15. Some variants of the VL method were adequate for analyses of cereal grains regardless of phytic acid level but none accurately measured phytic acid when at low levels in soybean flours. One variant of the HL method in which the 0.2 N HCl extraction media is modified to contain 10% Na₂SO₄, did accurately measure phytic acid levels in both cereal and legume flours regardless of endogenous phytic acid levels or matrix constituents.     

Genotype and Growing Environment Effects on the Tocopherols and Fatty Acids of <Emphasis Type="Italic">Brassica napus</Emphasis> and <Emphasis Type="Italic">B. juncea</Emphasis>

The effects of genotype and growing environment on the tocopherols and fatty acids (FA) of experimental Brassica juncea and B. napus breeding lines were investigated. For both species, with the exception of a few genotypes, the concentration ratio of γ-tocopherols to α-tocopherol was practically constant. The genotype influenced the tocopherol concentration in B. napus, and to a lesser degree, B. juncea. The environment also had a similar effect, and a positive correlation existed between the daily maximum temperature and the α-tocopherol concentration in B. napus. Genotype effects on the FA composition were significant for the conventional but not for Clearfield or triazine tolerant traits of B. napus. The genotype had no effect on the FA of the B. juncea genotypes. In contrast, the growing environment had a significant influence on the FA composition of both species with apparent influence from temperature and rainfall. For both species, the concentration of γ-tocopherol as well as total tocopherols was inversely related to the 18:3 concentration, which could have resulted from opposite and independent effects of temperature on the two variables. No relationship existed between the concentrations of tocopherol and the remaining unsaturated FA 18:1 and 18:2. The positional distribution of unsaturated FA within the oil triacylglycerol was a function of their total concentration.     

Novel diol spiro orthocarbonates derived from glycerol as anti‐shrinkage additives for the cationic photopolymerization of epoxy monomers

Shrinkage that takes place during polymerizations induces internal stress in polymeric materials generating a series of problems like poor adhesion to substrates and delamination in coatings or microcracks and microvoids in composites. Some additives like spiro orthocarbonates can reduce or eliminate this shrinkage. This paper deals with the synthesis of novel diol spiro orthocarbonates (DIOL SOCs) and their effect as anti‐shrinkage additives in the photopolymerization of the monomer 3,4‐epoxycyclohexyl‐3′, 4′‐epoxycyclohexanecarboxylate. It was found that increasing the concentration of the DIOL SOCs resulted in higher conversion of the monomer due to the presence of hydroxyl groups. The viscoelastic properties of the polymer products were also measured. It was observed that at 5 mol% of the mixture of DIOL SOCs there was an increase in the storage modulus due to the crosslinking produced by the bifunctional SOCs. However, at higher concentrations, a decrease in the storage modulus was observed. The level of shrinkage using the DIOL SOCs at 20 mol% was reduced by 45% when compared to the case without any additive. DIOL SOCs can be easily prepared by reacting glycerol with tetraethylorthocarbonate. These additives reduced significantly the level of shrinkage of the polyether derived from the diepoxycyclohexane monomer. Copyright © 2010 Society of Chemical Industry     

Absorption of silicon from artesian aquifer water and its impact on bone health in postmenopausal women: a 12 week pilot study

Background  

Decreased bone mineral density and osteoporosis in postmenopausal women represents a growing source of physical limitations and financial concerns in our aging population. While appropriate medical treatments such as bisphosphonate drugs and hormone replacement therapy exist, they are associated with serious side effects such as osteonecrosis of the jaw or increased cardiovascular risk. In addition to calcium and vitamin D supplementation, previous studies have demonstrated a beneficial effect of dietary silicon on bone health. This study evaluated the absorption of silicon from bottled artesian aquifer water and its effect on markers of bone metabolism.